How To SCAN 𝐍𝐢𝐠𝐂𝐨𝐦𝐒𝐚𝐭 𝟏𝐑 𝟒𝟐.𝟓°𝐄𝐚𝐬𝐭 / 𝐓𝐮𝐫𝐤𝐒𝐀𝐓 𝟒𝟐𝐄 On Redline Decoder
.
Scanning NigComSat 1R at 42.5° East on a Redline Decoder involves a few steps to set up and tune your satellite receiver. Here’s a step-by-step guide to help you through the process:
1. **Connect the Satellite Dish to the Decoder**:
Ensure your satellite dish is properly aligned to NigComSat 1R at 42.5° East.
Connect the LNB (Low Noise Block) output from the dish to the LNB IN port on the Redline Decoder using a coaxial cable.
2. **Power On the Decoder and TV**:
Turn on your Redline Decoder and your TV.
Ensure the TV is set to the input source that corresponds to the decoder (HDMI, AV, etc.).
3. **Access the Installation Menu**:
Using your Redline Decoder remote control, press the “Menu” button.
Navigate to the “Installation” or “Setup” menu (this may vary slightly depending on the specific model of your decoder).
4. **Select Satellite**:
In the Installation menu, find and select the option for “Satellite Setup” or “Antenna Setup”.
Choose “NigComSat 1R” or manually enter the satellite position (42.5° East) if it’s not listed.
5. **Enter LNB Configuration**:
Set the correct LNB type (usually Universal for most LNBs) and ensure the frequency settings match your LNB’s specifications (typically 9750/10600 MHz for Universal LNBs).
6. **Enter Transponder Details**:
Add the specific transponder frequencies, symbol rate, and polarization settings for the channels you wish to scan. Here are some details for NigComSat 1R:
Frequency: 12518 MHz
Polarization: Horizontal (H) or Vertical (V) depending on the channel
Symbol Rate: 29500 Ksps
7. **Blind Scan or Manual Scan**:
For a Blind Scan: This option scans all frequencies and transponders on the satellite. Select “Blind Scan” and start the scan. The decoder will search and save all available channels.
For a Manual Scan: Select “Manual Scan” and enter specific transponder details. Start the scan to find channels on that transponder.
8. **Save Channels**:
Once the scan is complete, the decoder will display the found channels.
Save the channels to your decoder’s memory.
9. **Exit the Menu**:
Exit the installation menu and navigate back to the main viewing screen.
You should now be able to view the scanned channels from NigComSat 1R at 42.5° East.
Tips:
Ensure your dish is accurately aligned to the satellite position for optimal signal reception.
If you experience issues with signal quality, check the dish alignment and LNB connections.
Refer to the Redline Decoder user manual for model-specific instructions and troubleshooting.
By following these steps, you should be able to successfully scan and view channels from NigComSat 1R 42.5° East on your Redline Decoder.
__________________________________
LINKS
WEBSITE:
www.pbteck.com
INSTAGRAM;
/ pbtecknology
FACEBOOK;
/ pbtecknology
TWITTER
/ pbtecknology
TELEGRAM:
t.me/pbtecknology
#pbteckinfo #lnb #gotvinstallation #multitv #dishtv #directtv #dstv #satellitetv #dish #satellitedish #satellitereceiver #pbteck #pbtecknology #canalsat #canal+ #freefire
Негізгі бет 💎 How To SCAN 𝐍𝐢𝐠𝐂𝐨𝐦𝐒𝐚𝐭 𝟏𝐑 𝟒𝟐.𝟓°𝐄𝐚𝐬𝐭 / 𝐓𝐮𝐫𝐤𝐒𝐀𝐓 𝟒𝟐𝐄 On Redline Decoder | Pbteck
Пікірлер: 5