Just bought this saw today. Thanks for the tip! I’m double checking mine tomorrow.
@berlinbuilds
3 жыл бұрын
Glad to help!
@mpkane24
3 жыл бұрын
Thank you, that was an easy, helpful walkthrough. Now, I need to check if my speed square really is square! :)
@berlinbuilds
3 жыл бұрын
Thank you! That is a good thing to check. It’s always nerve wracking if it turns out it isn’t and you’ve been using it for a while 😂
@ericledet80
24 күн бұрын
This was great. Thank you
@kevinblair191
9 ай бұрын
Appreciate the video! Just what I needed see.
@berlinbuilds
9 ай бұрын
I’m glad this could help!
@cassiehwilliams
7 ай бұрын
Thanks man! This was so helpful
@berlinbuilds
6 ай бұрын
Glad it helped!
@switchhanded
3 жыл бұрын
Oh! And how often do you have to recheck if the blade is square?
@berlinbuilds
3 жыл бұрын
I’m not sure the book answer on this. I usually just square them up once and roll with it, but I could see it being smart to double check your square every couple of months or so.
@TheCoffeeField
Жыл бұрын
What’s the point of the edge extenders?
@berlinbuilds
Жыл бұрын
Honestly they're pretty pointless when it comes to supporting material. One of my saws I pulled them off so I could run wings up to the saw, the other one I use them as handles when I pick it up and something to wrap the power chord around when I'm storing it.
@TheCoffeeField
Жыл бұрын
@@berlinbuilds that’s what I figured. Love your light add on though. I’m doing that next
@carterscustomrods
3 жыл бұрын
@ 2:21 ... headphone users, R🪦I🪦P🪦
@carterscustomrods
3 жыл бұрын
Lol I had volume up for the relaxed voice, and ended up jumping up to the ceiling and grabbing it as i looked back down, like a cat getting startled by a bear. Hot dayum son... Lmao
@berlinbuilds
3 жыл бұрын
Haha, sorry about that! My wife makes fun of me because I have a trick ear and am not always too conscientious of others' hearing!
@carterscustomrods
3 жыл бұрын
@@berlinbuilds hahaaa no worries. Your video came on after another video I watched, and it was while I had earbuds in, and changing blade on my 779. So the sound of you kicking it on made me darn near soil myself.. lmao!! I only have 1 functioning arm, so I tend to be a bit overprotective, and when you kicked your saw on, I had a million things race through my mind. Thought I had a flashback from my service days in Nam, and I wasn't even born at that time hahaaa. Thanks for the video, and the gift of allowing me to witness my entire life in a few short nanoseconds!!! Hahaaa.
@tomnorman5461
2 жыл бұрын
Video definitely needs some audio work...good lord!
@switchhanded
3 жыл бұрын
About how long did the setup take from start to finish?
@berlinbuilds
3 жыл бұрын
It took about 15 minutes to get the saw set up and then another 45 to get the blade square.
@John-mw3jf
2 жыл бұрын
why should a customer have to fine tune the adjustments for square? I really dont like the incremental shifting of quality control from manufacturer to user.
@berlinbuilds
2 жыл бұрын
Good question. I really wish we didn’t have too either! I have seen though from hauling my tools around in my trailer that things do get bumped and jostled a bit in transit, which naturally can loosen things up and make them go out slightly. I’m assuming (this is just me thinking) that most saws leave the factory all squared up. The nature of transit may make them go out slightly. Not totally sure, but those are just my thoughts on it.
@tomnorman5461
2 жыл бұрын
Hey CRY-BABY, you should be thankful for the ability to adjust the saw. Even if this saw (or any tool) wasn't perfectly aligned from the factory, eventually it will need to be adjusted due to "wear & tear" from normal use. Maybe you should stick with screwdrivers and sockets...leave the power tools to the adults!
Пікірлер: 26