now this is what you call an alternative....thanks for the effort and the info itll be a tech saver.....thanks again
@BreakersStereo
Жыл бұрын
Thanks!!
@torrescesar71
2 ай бұрын
You should compare the dd1 vs the multimeter to see how close they can get
@InLoveWithBass1990
5 ай бұрын
Thanks for the clear explanation.
@trendytoks4514
Ай бұрын
Extraordinary. It works perfectly in clean tone. Thanks a lot. Subscribed after the results.😊
@woodycreasman8226
Жыл бұрын
Thank you that really helped. 👍
@BreakersStereo
Жыл бұрын
Glad we could help
@michaelpearson6752
7 ай бұрын
Would you set the ohm for what the speaker is rated or the ohms that you would wire them?
@richb4gone524
5 ай бұрын
If u have a dual voice coil or multiple subs. Use the final OHMs(impedance) that goes to the amp after you wired the subs
@JetteJ3T1
10 күн бұрын
So the square root of 1 ohm? I have dvc 12 @ 2 ohms. Wired for 1ohm on the sub. 492 Watts amp 1ohm at the amp. So, use the square root of 492? Not x2? Thankyou! @richb4gone524
@ah4800
7 ай бұрын
He forgot to mention to use the power output number you want. If you amp does 200 watts rms but you only want 75 watts. Use 75 watts in the equation.
@mikhailtronik4322
7 ай бұрын
I think he was referring to how much the speaker can handle not the amp
@ashtonlennon9372
21 күн бұрын
He was talking about the speaker max RMS not the amp lol
@ae86fiend
Ай бұрын
Electromotive force is Voltage, not current. Current is measured in amperes aka amps.
@jesxsssss
11 ай бұрын
Why don’t you use a -5db test tone for the mids and highs and a -10db test tone for the bass. If the amp is bigger than the subs using a -7.5db test tone would be best. Using the 0db test tone won’t get the full potential of the amp. Most of the songs aren’t even recorded at 0db anyways.
@poochfazos
8 күн бұрын
My multimeter is just giving a constant reading whether I'm playing something or not 😒
@ali-sleimanchehade6129
Ай бұрын
Still waiting for the tweeter gain tuning and matching video 🥺🙏
@julesbruchez-theartofgrapp9646
5 ай бұрын
Also if you’re amp has a clipping indicator should you still use this method to ensure power is set correctly?
@fasterthanaturtle
2 ай бұрын
False.. that is only for the amp. You want head room in the amp so there is no need for clip and you need to adjust the power of the amp for the speakers
@thatguykai479
6 ай бұрын
I’ve seen people use .707 with the volts after sq root does it work ?
@JetteJ3T1
10 күн бұрын
I have a gain dial for channels 1&2 and another gain dial for 3&4. so my question would i figure for channels 1&2 by themselves, then 3&4. Its a 600 watt rms amp. Im only pushing 100 watts per channel @ 4 ohms. So would i multiply the 600 watts of the amp? Or the individual combined watts of channels 1&2? Then do 3&4 the same? Hope this makes sense TY!
@Thizz2979
3 ай бұрын
Do I disconnect door speakers to do this there running off aftermarket double din
@BreakersStereo
3 ай бұрын
You don’t have to just set the crossover to the highest settings on the front and rear channels on the headunit so you don’t damage them
@Thizz2979
Ай бұрын
Nice appreciate u I can’t believe I seen this so late now we can get at it 🙏
@luisparamo9402
9 ай бұрын
My subwoofer is 600 rms dvc4 ohnm. Does that mean 600x4 then square root of the total?
@karjalakat6139
9 ай бұрын
Yes
@michaelmueller7693
9 ай бұрын
@@karjalakat6139 what if you have 2 350 rms 4 ohm in parallel is it is it still just 350x4 or 350x4 then x2?
@danks2real314
4 ай бұрын
watever your going to wire it down to your amp is your final impudence.. if you go wire your 4 ohm dual down to 2 ohm at your amp then itlle be 600x2 if your not then x4 . again watever your last ohm is going in to your amp
@kevinlove2062
Жыл бұрын
Sorry if I sound dumb but how about if I’m using 2 dual 4ohm subs wired in series parallel at a 4ohm load each sub is 250w rms , would I be doing 500x4 or 250x4
@TheSeabeeMan
2 ай бұрын
If you have two 250w subs that are 4ohms each, then wiring them in parallel would give you a 2ohm load... ...so you would use 500x2... ...which equals 31.623V (i.e., AC VOLTAGE).
@TheSeabeeMan
2 ай бұрын
If you have two DUAL-VOICE-COIL 250w subs that are 4ohms each voice coil, then wiring them in series to give you 8ohms for each sub and then wiring both 8ohm subs in parallel (on the amp) would give you a 4ohm load... ...so you would use 500x4... ...which equals 44.721V (i.e., AC VOLTAGE).
@weztzideboyz7579
20 күн бұрын
@@TheSeabeeMan Sry if i look dumb, but I have 2 subs rated at 350 w rms each. Wired at 4 ohms. Just to be sure is this calculation correct(700×4) or is it (350x4)?
@zacholtman7849
Ай бұрын
What if amp outputs 1200 at 2ohm and sub is rated for 1000 at 2ohm. Also, inverse, amp rated at 800 at 2 ohm and sub is rated for 1000 at 2 ohm. Thanks! This is important for my next install.
@paweekdubaek
Ай бұрын
u should use RMS power of the speaker.
@erikmacias8893
4 ай бұрын
Can you turn the bass boost via remote knob up and down after this method?
@fasterthanaturtle
2 ай бұрын
Start high when setting the amp for clip and speaker power limits. Can reduce volume after, same as turning down the volume by reducing voltage
@jimmyramirez8844
2 ай бұрын
Why not set it to hpf?
@BreakersStereo
2 ай бұрын
The radio? Yeah if it has it yes set the hpf
@romeomwinx8584
29 күн бұрын
If my subs are 1000 peak watts each and they are 4ohm but have them wired down to 1ohm would I times that by 1 or 4?
@ImondiM87
22 күн бұрын
You go off the final impedance of the load. In your case, 1 ohm.
@romeomwinx8584
22 күн бұрын
@@ImondiM87 thank you that’s exactly what I needed clarification on. So with this formula I would need the square root of 1000.
@ImondiM87
22 күн бұрын
@@romeomwinx8584 exactly and you’re welcome! About to tune my new set up this weekend.
@TriniDoeBoy
6 ай бұрын
Ok, I have a Sony XAV 5500 head unit. Set my subwoofer level to max and then adjust my gains? Or setting the subwoofer level is only for the Alpine Head Units? I'm am basically a noob that is just trying not to cook my subs.
@BreakersStereo
6 ай бұрын
Yeah I think on the Sony it’s attenuation so set to 10
@julesbruchez-theartofgrapp9646
5 ай бұрын
Do you set the crossover first before setting the gains? Also, what if you run a DSP before the amplify? Will you set up a DSP and you set up all the crossover points and sum signals. But I set up the DSP set my summing signals set my channel paths and set all my crossovers then adjust the gain sensitivity on the amplifiers? It’s simple to do with my JL audio or D 900/5 because it has a clipping indicator. But if I run my DSP set all the crossover points do I have to turn the subwoofer crossover point off and the set the inputs sensitivity on my subwoofer amp? Or can I keep the crossover setting done in the DSP and still set the gain sensitivity on the for amp ?
@TheSeabeeMan
2 ай бұрын
It's best to adjust all of your settings to how you like them and then adjust the gain on your amp(s). But keep in mind that you're locked into those settings because that's what you set your amp gain/voltage point to.
@RMendes94
Жыл бұрын
And what happens when you tune your amp but your parking sensor goes incredibly loud? Can't find a solution
@BreakersStereo
Жыл бұрын
See if there is a setting in the vehicle control center that adjust the sensor volume.. what kind of vehicle do you have?
@RMendes94
Жыл бұрын
@@BreakersStereo I have a Peugeot 308 allure 2016, I've been checking in the menu but there is nothing about it, may I can get a scanner or something?
@Drippinonthedroop
Ай бұрын
What if your amp can't meet the rms of the sub? Does that matter?
@sniffer6285
Ай бұрын
Then you need a bigger amp !
@Drippinonthedroop
Ай бұрын
@@sniffer6285 i know. I wanna give my sub at least 800 (probably only getting half that at dynamic peaks maybe 350rms) . Its rated for 750rms. (L7s). Manual says 600rms at the specs Ive built it to. I mean honestly Im pretty happy with my setup in my 02 Taurus atm. Hard to imagine it much louder than it is now but the temptation is very real
@Drippinonthedroop
Ай бұрын
I mean what Id hope is the sub would sound better at any volume with it getting its recommended power. But is this just my misconception? Will it only sound louder which to many is better?
@samwads.
24 күн бұрын
Then you do the calculations for the RMS of the amp instead of the subs
@cdracos1
5 ай бұрын
You set for one mid. If you have 2 on a 2 channel amp I'm guessing you need to double the voltage figure ?
@xyphur
3 ай бұрын
No. The gain knob is adjusting each channel the same amount. Each channel has nothing to do with the other otherwise. Think of a multi-channel amp (2/3/4/5/etc, doesn't matter) as if it's a bunch of monoblock (1-channel) amps stuffed in a single box with one linked gain knob that controls them all equally. The math is the same regardless of channels, and the resulting voltage will thus be the same. The voltage you see at one output will be the same across all other outputs. Do as the video says on one channel, then move the multimeter to the other channel to verify. The reading should be identical (or very very close to it, accounting for any slight production variations between the same electronic components used in each channel, such as the transistors. There's always a small tolerance in these parts). If you want to be anal about it, do the adjustment again for the channel that reads the highest so you know that all others are safely below the max allowable setting. This will allow you to dial out those slight tolerances so they can't negatively affect your gear over time. Hope that's helpful :)
@Lu1s1005
3 ай бұрын
My speaker+tweeter in parallel has a final impedance of 2.66. My amp is 40w@4 and 60w@2. Would my equation be v=2.66•40 squared? How do i know how many watts to multiply 2.66 by?
@rbenas
3 ай бұрын
it is 2.66 ohm resistance to DC. Tweeter has very high impedance to lower frequencies. Calculate with speaker impedance (i guess 4ohm) only. Tweeter also must at least have series blocking capacitor
@truedunkin8818
2 ай бұрын
Mp3/flac/ wav file format for car audio?
@SkiFanatix
5 ай бұрын
On the subwoofer voltage you said 31. Then you set it to 3.1, I assume the decemal is in the wrong location on your math. I needed 34, but my amp maxed at 14. So i set it to 3.4
@descargasism
4 ай бұрын
31 is the right Number, you may need another more powerful amp to reach the voltage of your subwoofer, subs need a lot more power than a speaker
@SkiFanatix
4 ай бұрын
@@descargasism ok. you set yours to 3.1, so kind of confusing lol
@MEATY_BULL
Ай бұрын
Is this rms or peak power?
@paweekdubaek
Ай бұрын
RMS
@michaelsalyer4370
4 ай бұрын
Why turn the bass all the way up on the head unit
@dreybh7841
3 ай бұрын
Idk
@xyphur
3 ай бұрын
So that you set the absolute maximum output signal that the system will ever see, and set your gain based upon that. If you set your gain with a lower input signal than what the headunit can be set to output, then at some point in the future you or someone else happens to turn that bass setting up, you'd be overdriving the sub because the output gain of the amplifier will have been exceeded with a higher input signal than it was originally set for. It's a safety measure, as well as guaranteeing that you are setting the system up for it's maximum potential. Once the gain is set up with the bass at max, you can turn it down to where you typically want it, and still have the ability to turn it up if the need arises without overdriving your gear.
@FatSackoBudz
Жыл бұрын
so for dual 2 ohm with 1 ohm at box terminal should just rms of sub times 1?
@BreakersStereo
Жыл бұрын
Correct
@michaelcraig1690
3 ай бұрын
My speakers say 100 rms on box. So times that by 2 and get square root?
@BreakersStereo
3 ай бұрын
What is the impedance ?
@ScottYouTube123
Жыл бұрын
How do you tune a 4 channel amp that runs a sub as well as 4 speakers- thanks
@________GHOST________
10 ай бұрын
Not a good idea to run a sub on a 4 ch amp unless you have a 5ch amp to do so. All car subs do not need NO VOCALS coming out of a car sub
@Smxzzx
2 ай бұрын
Ya don’t run subs off a 4 channel just buy a separate mono amp or get a 5 channel
@akuma4u
8 ай бұрын
My sub is super under rated at 1500rms but most people put 2000 to 3000rms to it for daily. So do I still use 1500?
@stephenanderson1944
5 ай бұрын
I'm a little late to this so you may have figured out by now, but if I were you I'd still use the 1500, they say that for a reason so unless you don't care to blow a sub or two, I'd stick to what they say, most people may have gotten a "golden" pick but others may not
@BigDaddyBouncer100
10 ай бұрын
Are you doing peak watts or rms watts
@________GHOST________
10 ай бұрын
ALL RMS WATTAGE ONLY. Remember there is no such thing as PEAK WATTS
@haydenmacroberts4493
5 ай бұрын
@@________GHOST________ Thank you. been looking for this answer for awhile!!!
@lastcat
3 ай бұрын
To set my gain for my Subs. I have 2, each at 150 watts. Do I still value my amps output for 150 or 300 watts? Sure could use some help.
@TheSeabeeMan
2 ай бұрын
You add up all watts that you want your amp to produce (in total). In your case that would be 300w.
@cdracos1
2 ай бұрын
Why ?. Using a multimeter , I get NO reading playing a test tone unless my speakers are also wired up so I can hear the tone , what's that all about ??
@can48
4 ай бұрын
My subwoofer has a 4+4 ohm 500w rms value. Should I set the multimeter to 31 volts or 44 volts?
@akaaash111
4 ай бұрын
Wire your subwoofer in parallel. Then it will become 2ohms 500x2= 1000 √1000= 31.62 volts
@faisal6232
3 ай бұрын
i have jbl stage a9004 running 3.5inch in dash with hpf on and midbass in doors with lpf on in doors. i have high level inputs from DSP to amplifier. the issue i am facing is that if i try to adjust the gain from DSP then the AC voltage on speaker outputs does not change on the amplifier. The strange thing is that left channels from amp shows 14.4 volts and right channels shows 33 volts. wondering what could be the reason?
@BreakersStereo
3 ай бұрын
Ok sounds like either the amp or the dsp is bad. I’m guessing DSP since there is no output change when you try to adjust the dsp. 1. Try to bypass the dsp and test the left and right channels against each other to see if they are different. You can bypass the dsp by just hooking up your phones output with a cable that converts into an rca. Or any other source you can plug into the amp. If you still have the problem it’s the amp if you don’t it’s the dsp. Hope that helps
@faisal6232
3 ай бұрын
@@BreakersStereo yes, actually DSP is fine, the problem here is the high level inputs in the AMP are acting weird. i tried the RCA input in amp and L-R channels are fine. while using the fader in the HU, Left and Right are ok. so, now running from DSP to LOC to Amp. Thanks for your advice.
@danpallant3315
Ай бұрын
E = voltage. Not current.
@hgfdksk17
5 ай бұрын
This went a little too fast. Couldn’t follow along lol
@larrybrown9168
4 ай бұрын
I add these videos to a playlist for DIY then I go to speed settings and slow it down. This was real informative but I feel you on the speed.
@rticul8862
Ай бұрын
Pause
@andrewr5046
15 күн бұрын
Perfect
@poochfazos
8 күн бұрын
Yeah same
@SuperBubba360
Жыл бұрын
How do you turn the crossover off on an amplifier?
@TheBlackz05
Жыл бұрын
Lowest number if its the hpf only and highest number if its lpf only... most amps have an option of hpf/lpf/through on the crossover selection, in this case, set it to "through"...
@akuma4u
8 ай бұрын
Most mono amps do not have an option for off. So what most people think is off is really setting it to Maximum. That's not really off its more like full open. To be honest, I'd do the gain setting with it full open and then again with it set to around 80hz and see if you get same results (same spot where the gain ends up being)
@charger6773
11 ай бұрын
Do the speakers need to be unhooked from the amp when tuning the mids & highs with the multimeter ?
@mikestivers8302
10 ай бұрын
yes you want to run your engine, so alternator is feeding the highest power to the amps. disconnect the speaker wires!!
@luisparamo9402
9 ай бұрын
@mikestivers8302 how come I cannot get a stable reading for my amp[subs]...but I can for my highs[amp]....the reading for my subwoofer amp is all over....yet when I get the reading for highs amp it's stable 1.1...1.3..1.5...2.0...etc??
@mikestivers8302
9 ай бұрын
are you in the A/C Voltage setting? those look like fluctuations from listening to music..? use a test tone at 50 hz. i just did 2 amps, run engine, do the math, and get the gain turned until you hit target voltage. keep in mind, if your SUB say's it will handle 500 watts but your AMP only puts out 250, test the math for 250.@@luisparamo9402
@michaelmueller7693
9 ай бұрын
What if you have 2 350 rms 4 ohm wired in parallel so 1 ohm is it 350x4 or 350x4 and then doubled ?
@ttwizted6020
4 ай бұрын
No it would be 700 x 1 I believe so 700 rms total.
@xyphur
3 ай бұрын
First off, your impedance math is incorrect. 2 x 4ohms paralleled isn't 1ohm, it's 2ohms...
@nick_sometin7791
11 ай бұрын
I have the skar dual evl 12s, and the amplifier rp 2000. Do i do the square root of the amp watts rms which is 44.72 or the subwoofer rms which is 2500, and the square root of that is 50 so when i have my meter on the speaker terminals do i use 44.72 or 50, i see people say its the rms of the amp
@kmcmuscle9973
6 ай бұрын
Evl is 1250 rms 2500 max
@danks2real314
4 ай бұрын
@@kmcmuscle9973he has 2
@swashbucklincocksucklinpirate
2 ай бұрын
Since your amp cannot put out 2500 tune to amp to avoid distortion
@fasterthanaturtle
2 ай бұрын
Dial in the calculation to the lowest of the two. Neither can go higher if both can't go higher
@luisparamo9402
9 ай бұрын
Are we suppose to use these same steps to set bass boost ?
@fishrrelaxing9361
9 ай бұрын
Never use any loudness or boosts of any kind on headunits or amps.. all it does is muddy the signal and clip
@ttwizted6020
4 ай бұрын
What if it doesn’t and it sounds good. Still say no to using bass boost??
@derekmeyers5966
Ай бұрын
@ttwizted6020 It may sound good but all bass boost and loudness do is dirty the signal up and stretch the sine waves. It can still sound fine but your sub will not like you. You should be able to reach your bass boost "max" without it but it will sound more clear instead of boomy like how a lot of people think subs are supposed to sound
@robertohara9547
Жыл бұрын
after setting gain if you would like a 80hz lpf how would you know when its set to 80hz? or any crossover without a cc1:) thanks!
@BreakersStereo
Жыл бұрын
To answer your question if have a crossover on the headunit use that because you can get the accurate setting, if you’re using the crossover on the amplifier, normally it gives you a range and you kind of have to gauge it based on the numbers. So you can come close to 80hz but not accurate. But if you don’t have it on the head unit, don’t worry it doesn’t make a huge difference if let’s say you end up at 85 Hz versus 80hz.
@rbenas
3 ай бұрын
1. turn off crossover 2. play your 80 hz test tone at normal level (just enough to get reliable voltage measurement at next step) 3. measure output AC voltage, lets say get X 4. turn on crossover and dial knob until voltage decreases to X * 0.501 (if your amp crossover is 12dB/octave slope) example: you measure 8.4V at 3rd step, so you turn knob until you see 4.2V constants for other slopes: 6 dB/octave -> 0.708 12 dB/octave -> 0.501 18 dB/octave -> 0.355 24 dB/octave -> 0.251
@jo3rdchannel940
Жыл бұрын
For the AC do I set it at 200 or 250 ?
@cdracos1
2 ай бұрын
200
@kaivinson1777
18 күн бұрын
Video moves way ro fast
@2hardbackrub743
15 күн бұрын
🤯🤯🤯 fkking hardcore
@andrew7202
4 ай бұрын
Is it 500 peak or rms should be a little more specific my guy smh
@catsnatcher9197
3 ай бұрын
I think RMS
@cowboyexecution3642
24 күн бұрын
Is this for 2 subs
@dinxsy8069
13 күн бұрын
sets up an amp not knowing if the head unit is clipping, "set it about 90%" talk about piss into the wind. Some head units can do 100% no problems, it's not about branding it's the quality of the components in a head unit, could pay $1000 for something but if it has bad caps for example it'll be hit or miss on the clipping, An oscilloscope isn't much to buy on eBay either. I feel the channel is a copy pasta of content
@redek1503
Жыл бұрын
so i need to turn up the sub level all the way up on my alpine cde 143bt and then turn the gain up? i set it up with the sub level at zero, did i do that wrong or is it ok?
@BreakersStereo
Жыл бұрын
Set volume on your alpine radio to 31. Then turn your subwoofer level on the radio to all the way up to 15. Then set the gain.
Пікірлер: 125