Hey Luke , lot`s of great info on setting up a rifle ... enjoyed watching the show
@windblown466
6 ай бұрын
Thank you for this! It’s easy to follow and understand. VERY HELPFUL!
@wighillparkgunstv2257
Ай бұрын
You are so welcome!
@markhomer5704
11 ай бұрын
You can get MOA scope inserts quite cheep, saves any potential crimping of the scope tube.. Never liked the idea of shimming, scope rings are designed to be flush / parallel with the tube of the scope.. Certainly wouldn't risk it on a expensive item, maybe one of them ones you get in a rifle / scope package for £200 I'd chance it..
@JOHNJONES-qo3fh
13 күн бұрын
Great solution .
@wighillparkgunstv2257
13 күн бұрын
You’re welcome
@peteralexben
11 ай бұрын
shimming is a very bad practice ,jou bend the scope and the internals can be harmed . use a moa rail ,or adjustable mounts , from fx ,vector , sportsmatch and more brands . .
@pahlevan1352
7 ай бұрын
thank you, a very neat and easy solution
@wighillparkgunstv2257
Ай бұрын
You're welcome!
@brianvogel5028
5 ай бұрын
Brilliant! Thank you very much mate.
@wighillparkgunstv2257
Ай бұрын
No problem 👍
@bltefft
2 ай бұрын
I had to shim the rear of my Vortex Crossfire 3-9x40 scope. I use three slips of a sprite bottle. I torqued the 8 screws through the rings to 15 in-pds. I'm on bullseye now
@wighillparkgunstv2257
2 ай бұрын
👏
@1noelj
2 ай бұрын
Thanks that sorted out my problem very helpful
@wighillparkgunstv2257
2 ай бұрын
Happy to help
@1noelj
2 ай бұрын
@@wighillparkgunstv2257 Except when it was the other way around on another gun could not get the elevation down shimming front mount up?
@CutlassOutdoors
9 ай бұрын
This is not a good way to add taper to your system. There's a right way and a wrong way to add taper, and this is like the wrong way, only faster and cheaper. Even on an air gun, this is going to lead to problems holding zero, crimped body tubes, etc. Get a tapered base or a tapered mount. Shimming, especially with plastic, is a great way to ruin a scope and introduce point of impact shift. This may work temporarily on an airgun, until it gets bumped around at all, but I hope you're not too invested in the scope because this could/will damage it. It will not work on any sort of firearm with recoil or piston airgun with reverse recoil. This sort of "hack" is akin to covering up your car's check engine light with electrical tape and considering the problem solved. Videos like this are why KZitem really needs to bring back the dislike count.
@KillerFknWolf
5 ай бұрын
great tip, i've had this issue myself. would it not be easier to wrap tape of some sort around the scope instead of trying to juggle those little slips of plastic?
@galesams4205
9 ай бұрын
Out of elevation just raise the scope mount, never like shims. Mounts are small med. high.
@neiledwards8931
3 ай бұрын
Quite simply , get a one piece mount from Sportsmatch which is made for the job , why damage the scope body if over tightened . Be wise .
@carmelopolizzi8079
4 ай бұрын
Shim the mount rather than the rings to avoid potential harm to the scope seems to be the consensus
@chriswest4576
11 ай бұрын
Good advice Luke mate, any update on the m60 review yet ? Cheers
Пікірлер: 22