I bought the 220VAC 1500W VFD & spindle motor for my DIY CNC router. The manual was pretty good,(****), and support was fair. I had a problem getting the multi speed feature working, and the vendor just stopped answering my emails. I figured it out anyway and forwarded the answer to them. overall 4 stars of 5. Vendor says braking does not work for my unit, I just wonder if they know the product well enough.
@huanyanginverter6516
11 ай бұрын
kzitem.info/news/bejne/tq6KmK1um5Fhhno
@umargul5644
4 жыл бұрын
Well done sir very useful
@spongebobpatrik3042
4 жыл бұрын
Thank you broather huanyang🙏🙏🙏👍👍👍👍👍👍👍👍👍
@aticafloorable
6 ай бұрын
sr what are the parameters so that when you stop the engine it stops faster. and the parameters for acceleration or starting of the engine. thank you
@huanyanginverter6516
6 ай бұрын
Your sketching is too simple, I don't understand what you mean.. What is SR?
@clidersemedo8013
16 күн бұрын
Hello, I bought the same model complete spindlle kit and 2.2kw water cooling inverter. but I'm having problems with loss of torque at low rpm Is there any way to adjust this so as not to lose torque? Thanks
@huanyanginverter6516
13 күн бұрын
Low RPM? How low is it? High-speed motors cannot operate at low speeds. It will burn out the motor
@clidersemedo8013
13 күн бұрын
@@huanyanginverter6516we are talking about 4000 rpm even at 4000 rpm it can burn?
@huanyanginverter6516
11 күн бұрын
@@clidersemedo8013 Your motor is 24000 rpm. You are dropping to 4000/per minute, which is not acceptable
@clidersemedo8013
11 күн бұрын
@@huanyanginverter6516 The rpm values on the Mach3 are not the same as those on the frequency inverter. The values are always fluctuating, more or less for example, if you put 16000 rpm on the Mach3, in winter it appears 16345 or 15857 +/- It never reaches 16000 rpm correctly. someone help please.
@huanyanginverter6516
11 күн бұрын
@@clidersemedo8013 "For the VFD, an input of 10V will reach the maximum frequency. The frequency is directly related to the 10V input voltage. Slight fluctuations in the 10V voltage can affect the frequency. You can use parameter Pd071 to delay frequency fluctuations."
@spannerman4886
2 жыл бұрын
What are the settings for the UK 230 Volts AC @ 50Hz please?
@VSongu
Жыл бұрын
Hi there! I have bought a Huanyang spindle and the same VFD as in this video. I have wired it as you U=1, V=2, W=3. But my spindle spins backwards (in counterclockwise direction). What is wrong?
@huanyanginverter6516
Жыл бұрын
U=2 V=1 W=3 It's normal
@VSongu
Жыл бұрын
@@huanyanginverter6516 Thank you!
@VSongu
Жыл бұрын
@@huanyanginverter6516 But probably I can swap any two of those, is it true?
@huanyanginverter6516
Жыл бұрын
U=2 V=1 W=3
@woodideias
Жыл бұрын
Can you help me. My spindle not run. (Erro Lu5) I use huanyang VFD 1.5kw 220v
@huanyanginverter6516
Жыл бұрын
This is a hint of low voltage
@huanyanginverter6516
Жыл бұрын
Process video shot and sent to me
@jstef4136
4 жыл бұрын
I have the (HY02D211B)110v vfd and 110v 2.2kw spindle, 8.5 amp. What are settings for PD006, PD007,PD009,PD010,PD011, PD041,PD120PD142,PD174. Thanks, Joe
@huanyanginverter6516
4 жыл бұрын
None of these parameters need to be changed. You just need to change the frequency.
@jstef4136
4 жыл бұрын
@@huanyanginverter6516 .my question is in my 110v vfd ( and 2.2kw 110v spindle) the settings for pd 173, 174, and 176 do not stay changed . Keeps resorting back to 220, 11 amps and "0"....I need 110v, 20 amps, and "1" for 60hz. Maybe these settings don't matter, IDK... all other parameters retain their changes that I made. My vfd does say 20amps on label, although when spindle up to 24000 rpm, amps read 2.0 on display
@huanyanginverter6516
4 жыл бұрын
@@jstef4136 20A is a limit number... Normal operation is far lower than 20A
@jstef4136
4 жыл бұрын
@@huanyanginverter6516 but what about volts and Hz? do I have to reset these everytime I turn it on? I need 110v and 60 hz.
@huanyanginverter6516
4 жыл бұрын
@@jstef4136 Input voltage does not need to be set.. The output rate must be set to the same frequency as the motor. This is very important.
@geiermichel
Жыл бұрын
Alles schön und gut,aber mit welchem Ausgang kann ich ein Relais schalten und welche Parameter müssen dafür wie eingestellt werden.
@huanyanginverter6516
Жыл бұрын
Pd052 parameter
@geiermichel
Жыл бұрын
Was ist das für eine Antwort. Welche Ausgänge werden dann dafür verwendet. Man sollte das schon ausführlicher beschreiben
@tonygalluzzo4856
3 жыл бұрын
I have this package from you, it was working well, between bit changes it will not work. When pressing "RUN", VFD shows spin up to 7800 rpm, the spindle makes noise however the bit does not spin. I can move the bit freely by hand, spindle seems to be making noise. Once it hits 7800 RPM, "EOCA" appears on the VFD and spindle doesn't make noise anymore. Please help!
@huanyanginverter6516
3 жыл бұрын
Most likely it is UVW, missing a phase
@glengroenendaels4229
Жыл бұрын
Good morning My huanyang HY02D223B spindle continues to turn at 200rpm when I enter the M5 command can you help me?
@Pinmantella
2 жыл бұрын
Where do I install my output ground going to my motor? My machine has 4 wires, it is not a spindle.
@huanyanginverter6516
2 жыл бұрын
The UVW is connected to the motor, and that's it
@labautoman
5 жыл бұрын
i have a GT-4R0G-2 trying to run 3.2kw spindle. Got the spindle to auto tune but can not get it run via keypad and pot on front of inverter. It is slightly different than this model. any help would be appreciated. then i have to get it working with Mach 4
Good video! That sucks we don't have an amazon account, we get all the cnc parts from AliExpress stores. I think we already ordered a spindle from you...
@msdesignru
6 жыл бұрын
And don't put the links when you commenting other channels videos, youtube delete them automatically
@huanyanginverter6516
6 жыл бұрын
Thanks for your interest.I will post more and more videos. You can order from AliExpress.
@msdesignru
6 жыл бұрын
Already ordered! Check out video-reviews on my channel.
@msdesignru
6 жыл бұрын
Do you have something to review on our channels? We can review any CNC parts either in Russian or English.
@msdesignru
6 жыл бұрын
Could you please give me a link on your AliExpress official store?
@jimernst9735
5 жыл бұрын
any info using speed control work with mach3 ?
@huanyanginverter6516
5 жыл бұрын
kzitem.info/news/bejne/tq6KmK1um5Fhhno
@ferdieedquiban9047
5 жыл бұрын
What's the operating voltage of this VFD shown on this video? Thus it comes with the braking resistor? Also thus the 220V model VFD will also work using step-up transformer if 110V was only available power source?
@huanyanginverter6516
5 жыл бұрын
The video shows 220V power. if you use 110V, the spindle motor also must be 110V.And It can stop in 5 seconds without adding brake resistor.
@ferdieedquiban9047
5 жыл бұрын
Can I use a step-up transformer from 110V to 220V if 110V source was not available?
@huanyanginverter6516
5 жыл бұрын
You buy a 110V motor and VFD
@ferdieedquiban9047
5 жыл бұрын
I had 3000W step-up transformer to be use with 220V VFD version that’s why I am asking. Will it work?
@huanyanginverter6516
5 жыл бұрын
has an effect. . . . But the load can't be too heavy.@@ferdieedquiban9047
@gagangfebrianto2016
6 жыл бұрын
Can you help me. My spindle not run. I use huanyang VFD 1.5kw
Hola, tengo un problema, en sentido FOR me va todo bien pero cuando cambio a REV empieza lento y se para. Porque puede ser? En FOR me gira en sentido antihorario y me gustaria que girara en sentido horario
@huanyanginverter6516
3 жыл бұрын
UVW, changing to UWV can solve your problem
@pharys10
3 жыл бұрын
@@huanyanginverter6516 Gracias, ahora va bien
@huanyanginverter6516
3 жыл бұрын
@@pharys10 Ok
@runbou3485
Жыл бұрын
ឣរគុណ
@Q1Engravers
4 жыл бұрын
This I tried and smells came from controller, be aware; I have spent weeks trying to get it to work and there is no tech support
@huanyanginverter6516
4 жыл бұрын
whatsAPP:+86 18072595511 Be sure to contact me, do not continue to test. There must be something wrong with the parameters.
@huanyanginverter6516
4 жыл бұрын
SKYPE: China-hy Wechat: China-VFD
@kagstand09
4 жыл бұрын
Huanyang inverter I am having same trouble. Been three days and no response from company.
Пікірлер: 98