Bless you JK for sharing your life and wisdom with us:) great educational video:)
@MitchellsBackyardLogging
2 жыл бұрын
That’s a cool build man I like the way it ran
@JKSawShop
2 жыл бұрын
It was decent
@ScrewdriverTUNING
2 жыл бұрын
Keep up the fantastic work. Your attention to detail is fantastic my friend .!!!
@JKSawShop
2 жыл бұрын
Thank you Billy from Philly. I try to do the best I can most of the time.
@shapeshifter7753
2 жыл бұрын
Thanks for going through all this!! I’ve got two dump find 55’s and two 028’s from the same place. Already did a custom muffler on the 55 which turned out great! Next will be the pop up piston and mild port work on the stock jug. I really liked that saw you did for Dan👍
@JKSawShop
2 жыл бұрын
Dan’s has a 55 pop up piston and some port work. It is definitely a great runner. There is quite a bit of work that goes with the 028 piston swap, they are not a direct bolt on a go.
@shapeshifter7753
2 жыл бұрын
I may have to buy a piston yet… haven’t tore down the 028’s yet to see if they are any good but they’ve got good compression and I’ve had em both running so 🤞 should be a fun journey! Been saving up parts for this for a couple years and watching your vids is really helpful 👍 thanks JK!
@JKSawShop
2 жыл бұрын
@@shapeshifter7753 Thank you it means a lot to me.
@SouthernPatriot1
2 жыл бұрын
Awesome mod brother! Look forward to seeing more from this lil beast. God bless.
@JKSawShop
2 жыл бұрын
There will be more to the story, it’s being written now
@SouthernPatriot1
2 жыл бұрын
@@JKSawShop 😂
@justinweaver8787
2 жыл бұрын
Awesome build buddy Cant wait to see more on it!
@JKSawShop
2 жыл бұрын
It’s not what I expected
@ClintsHobbiesDIY
2 жыл бұрын
Great R&D vid Josh.
@JKSawShop
2 жыл бұрын
I just had an idea and thought I would try it out. I am still planning on trying to race both of those saws.
@KainKustomGarage
2 жыл бұрын
That's Awesome! She runs nice!🤩
@JKSawShop
2 жыл бұрын
This one does real good
@IndianaDoug
2 жыл бұрын
Cool mod👍🏻 lookin forward to seeing it on the wood.
@JKSawShop
2 жыл бұрын
I’m going to go ahead and spoil it… It is not horrible bad, but it is not great either
@timberslasher4899
Жыл бұрын
That was a really good video, I actually might have learned something 🤓 I have a 41 that is toast that I want to build just to see if I can. 😆😆
@JKSawShop
Жыл бұрын
I done really mean 41 for muffler delete
@timberslasher4899
Жыл бұрын
@@JKSawShop That's awesome! I'm no porter.... Yet. I need to just build a few and make them run first....lol. I'm gonna split this one just to be doing it if you know what I mean...
@JKSawShop
Жыл бұрын
@@timberslasher4899 The best advice I have for the 41 is to get air to flow better, and throw a little bit of timing advance to it.
@timberslasher4899
Жыл бұрын
@@JKSawShop I will remember that... Thanks!
@jackylsmith8138
2 жыл бұрын
My 55 rancher came with a 3/8 chain and a 18” bar brand new in 2000. She still runs nice today.
@JKSawShop
2 жыл бұрын
That is awesome. I just really like to play with those little 55s
@jonbobskunkworks
2 жыл бұрын
Looking good!
@JKSawShop
2 жыл бұрын
Thank you Jon Bob
@StevenLettsPerformance
2 жыл бұрын
Nice work buddy! I'm curious the longevity of that piston thinning out the top.
@JKSawShop
2 жыл бұрын
We will find out. I’m planning on putting a lot of run time on it
@thecollectoronthecorner7061
2 жыл бұрын
I bought a new rancher 55 in 2000. Spent more time putting the chain back on the rollertip bar than I did sawing. Next day bought a new non roller tip bar. It never oiled the chain enough to suit me. I tore all that loosey goosey VI stuff loose. Its now in a 51 housing. Engine still runs good. Dont use it very much. I would rather use my 68CC 1967 Lombard or a 58 cc super XL automatic. Me and roller tip bars and plastic saws dont get along very well.
@JKSawShop
2 жыл бұрын
I found a surplus of 51’s I kinda enjoyed building them.
@justinweaver8787
2 жыл бұрын
I sure as crap wish my muffler would have went on that easy lol great job buddy.
@JKSawShop
2 жыл бұрын
There is a trick to everything
@transdimensionalist
2 жыл бұрын
i had trouble getting mine on, seems the casting needs opeing out to allow the studs into proper position
@simpleman4224
2 жыл бұрын
Nothing beats a failure but a try! 👍👍👍👍🇺🇸🇺🇸🇺🇸🇺🇸🙏🙏🙏🙏
@JKSawShop
2 жыл бұрын
Always keep trying new things.
@PhilDuguay138
Жыл бұрын
So do you really need to cut a relief for the spark plug? Got a hyway CP cylinder and went for the 028 because squish was horrible on the hyway kit, 0.058 if i aint mistaken, now with a 0.015 gasket i'm at 0.023 with the 028 piston, but i'm not touching the spark plug, should i still notch a dimple in it or leave it as is?
@JKSawShop
Жыл бұрын
This one I had to
@82f100swb
2 жыл бұрын
I ended up with a .010 base gasket to get to .020 squish, the popup was actually hitting the chamber with no gasket. With the .010 gasket I was able to get away with just a second gasket on the plug. I've kind of always felt my built 55 was a turd, even when it was bone stock, now it's just a polished one... LOL
@JKSawShop
2 жыл бұрын
This one does all right. It’s defiantly not the powerhouse that I think it should be. It would probably do a lot better if I would put the 325 chain on it.
@82f100swb
2 жыл бұрын
@@JKSawShop I've ran mine with both, both my 254 and 026 will cut circles around it. It's better now with the HDA120, but it's not in the same League
@JKSawShop
2 жыл бұрын
@@82f100swb I don’t think they will ever be in the same category. Just trying some ideas.
@82f100swb
2 жыл бұрын
@@JKSawShop The 254 has more stroke so I think it's going to be hard to match. It's always been my target though. My 026 is just a freakshow. A 48cc saw has no buisness running like it does.
@JKSawShop
2 жыл бұрын
Longer stroke helps the 254.
@easingrapod1274
Жыл бұрын
Hi. do I have to make any modifications to put a stihl 028 piston in it?
@JKSawShop
Жыл бұрын
Yes you need to widen were the rod’s little end goes
@lennie8098
2 жыл бұрын
Hyway makes a dome piston 46mm for the Husky 55
@JKSawShop
2 жыл бұрын
The 028 super piston is a little taller than the 55 piston, I do have a 55 cylinder and a 55 pop up on my other 51. Just wanted to mix it up and try something different.
@wilkey40
Жыл бұрын
Some OEM 55s are 45mm and the 028 46mm piston will not fit
@JKSawShop
Жыл бұрын
The closed port 55s are 45 just like the 51 and the open port is 46
@brianmorrow6355
2 жыл бұрын
I'm in the middle of building two 55s waiting on an 028 piston
@JKSawShop
2 жыл бұрын
It works. There’s just a little bit of things you have to do, I’m going to run this one for a while and then I may end up buying a better piston.
@brianmorrow6355
2 жыл бұрын
@@JKSawShop I'm waiting on one from Lil red shed we will see what it does.
@JKSawShop
2 жыл бұрын
You could probably get by using the base gasket and .030 squish. That way you dont have to index the plug or relief the piston.
@brianmorrow6355
2 жыл бұрын
@@JKSawShop I've got 2 base gaskets to choose from and the head that's on it is a farmertec but the squish is like .038 with no gasket so it's pretty loose. That's what made me go with the 028 piston hopefully to get a little more compression and a double ring piston should have less blow by
@JKSawShop
2 жыл бұрын
@@brianmorrow6355 it will pull a 20”standard 3/8 in soft wood, struggles a little in white oak. Gonna go back to .325 chain more than likely.
@dentonsbackyardshow1013
2 жыл бұрын
Now adays they tend to market throw aways. Not mamy prople work on small engines anymore
@JKSawShop
2 жыл бұрын
I do a lot of trying to save em
@jackfrosty79ify
4 ай бұрын
Piston clip suck
@JKSawShop
4 ай бұрын
It’s a necessary evil, I can’t tell you how many of them I have lost.
Пікірлер: 64