"Good news! I got the Twike registered!" I can only image the poor sods at the DMV seeing Rob walk in and wonder what fresh hell he's bringing now :D
@nullplan01
5 ай бұрын
I'd be elated. Imagine sitting in the office and having to register another Dodge, another Ford, another Dodge, another Ford, and on and on. And then Rob walks in and you know you will have some excitement for once.
@milohobo9186
2 ай бұрын
Maybe they made some side bets that this would happen
@silent5950
2 ай бұрын
@@milohobo9186"I bet the motor will cut out as soon as he gets up to freeway speed!"
@jbran7817
7 ай бұрын
27:05 “a friend who’s really good at identifying connectors” is definitely Alec from technology connections
@raven4k998
4 ай бұрын
he fixed it and crashed it so he can fix it again🤣🤣
@hyralt
8 ай бұрын
I love how deeply you went into all this. These fix videos are my absolute favorite of all the ones you do. I can’t wait until the next one!
@felio_
7 ай бұрын
There's not a single bad video from this man. I watched him build a chicken coop like it was a movie.
@Nihilimus
7 ай бұрын
@@felio_ Only topped by installing insulation in his spider infested walls. I'm (unironically) eagerly waiting for the sequel "I put insulation in my ceiling".
@Trawets9215
7 ай бұрын
I was going to type almost the exact same message @hyralt, I'm not saying I'm a smart man, but they do say great minds think alike.
@patconner2638
7 ай бұрын
Agreed on all points, and eagerly awaiting an update on the bus build! (even if just the closure dramatically hauling it to scrap if he's lost interest after... 2? 3? years??)
@ACplanet
7 ай бұрын
I like it when he spends way too much time on small things that should be a quick fix
@nobodynoone2500
7 ай бұрын
29:20 The face of the realization you just sunk nearly 10k into a deathtrap that sucks in every imaginable way, and may actually die for content.
@leexgx
7 ай бұрын
At least it didn't lock the steering when he was doing 25 down the road with no brakes
@hershelshochter4703
7 ай бұрын
in case you're reading this, you can loosen up hot glue with alcohol. just squirt some rubbing alcohol in there and it'll let go without any damage to the cells or electronics
@Tibyon
7 ай бұрын
I was coming here to check that someone said this!
@sirBrouwer
7 ай бұрын
instructions unclear. I stopped reading at. ''with alcohol'' and went to the pub. I don't know if it will do much to the glue but I am not complaining.
@NicklasUlvnas
7 ай бұрын
@@sirBrouwerRemember that it can take more then one try!
@sirBrouwer
7 ай бұрын
@@NicklasUlvnas Sure I will keep on trying. Luckily I can walk to the pub.
@saberwarthog
7 ай бұрын
I was thinking Isopropylic Alcohol, but yeah, rubbing alcohol is quite enough to do the trick, either of those works a charm to loosen hot glue.
@rupertkingsley
7 ай бұрын
Other KZitemrs are quitting or struggling with an over ambitious upload schedule. Meanwhile I’m genuinely pleased when Aging Wheels pops up with a quality video every now and then. Genius!
@PsRohrbaugh
7 ай бұрын
Life is hard for everyone right now. Plenty of non-youtubers struggling with burnout but still gotta pay the bills somehow.
@afterthought3341
7 ай бұрын
We are all F@rked!@@PsRohrbaugh
@Twofrogsonecup
6 ай бұрын
sometimes I just sit on KZitem refreshing for hours just waiting for him to post a new video. life is pointless without these videos.
@Llamarama100
7 ай бұрын
It's like a Reliant, except somehow less safe and more terrifying
@SolarWebsite
7 ай бұрын
I've never driven a Reliant, but I did test drive a Twike once. "Less safe and more terrifying" sums up the experience nicely. The steering instability at anything over 50km/h was amazing, I had to use two hands to stabilise the damn thing. Also, it was twenty years ago, so it had the NiMH batteries - so no range to speak of. I can't understand people buying a Twike new for the exorbitant prices they asked good good. You'd be better off in all respects with a used Nissan Leaf plus a road bicycle for exercise.
@tezy0193
7 ай бұрын
@@SolarWebsite its actually bs that reliants are unsafe and terrifying (thanks topgear i guess...) its pretty hard to roll one and they drive totally fine, like a normal car .. they modified the one's in the show to make them roll easy
@Dr.W.Krueger
7 ай бұрын
You have no idea what you're talking about.
@luminousfractal420
7 ай бұрын
@@tezy0193he had a flying version in his back yard. It had 4ft rotors on either side, vertical takeoff. He said it cost less than a motorbike to run but they banned him from flying it due to "theres no highways in the sky". One unimaginative judge held the world back 100years 🤦 if he acted as immorally as elon or google he'd be that billionaire right now.
@Varadiio
7 ай бұрын
@@SolarWebsite Considering where most of the funding went, I think that he could have built something better for the price. I mean the cost for his repairs and buying used. The new price is just bananas (yea I know the 3 is out of production). There is typically something very important to factor into DIY projects: The DIY solution is not cheaper than buying. This is a trap common to woodworkers. Twike has created something so overpriced that DIY could actually be both cheaper and safer. The thing that keeps people like Aging Wheels going is the creation of things that aren't on the market, bespoke things. The electric Escape is a good example. It doesn't matter too much how expensive your DIY project is, if you're building something that doesn't exist commercially. I'm sure he knows all this which is why he's disturbed a bit by the price he paid to upgrade something well beyond its maximum value (aside from collectors speculations). All that is to say, companies like Twike are hurting the hell out of EV, green, what-have-you ecological markets with obscenely priced unsafe oddities, trying to fill a niche which is unironically better served by building your own.
@barefootalien
7 ай бұрын
Oh my god, that crash description was hilarious! The slow revelation from blinking in confusion just as you were sitting there in the ditch, stunned, toward fully understanding the crazy sequence of events that aligned themselves to cause it, and then to rewatching the panicked flapping with understanding... so good!
@KlueBat
8 ай бұрын
I can not imagine how terrifying this thing would be to drive in traffic.
@FtungusAmungus
7 ай бұрын
I've ridden an actual pedal power recumbent in traffic. Terrifying. But more stable than this, and easier to leap out of while screaming.
@robertschnobert9090
7 ай бұрын
There's so many people addicted to hard drugs like heroin or alcohol. And they're playing Candy Crush in their smartphone while driving under the influence. And they of course drive huge cars they wouldn't even be able to control sober. And they will keep their driver's license even after they murder people with their SUV because taking a license away is almost impossible in the US. Haha 🌈
@noneyabizz8337
7 ай бұрын
As bad as people are and as little as they pay attention... Wow
@tarstarkusz
7 ай бұрын
He should have just got a regular e-velomobile. Having to register and insure this thing is ridiculous. I don't even know why it has to be registered and insured. Though, most e-velomobiles have to be under a certain wattage determined by the state. In my state, I think ebikes are limited to 1hp. Velomobiles are very fast. Even though they are heavier than a bike, they have excellent aerodynamics. Legs alone can maintain 30-35mph.
@Padlock_Steve
7 ай бұрын
its not meant for NA hell traffic
@theackshow5048
7 ай бұрын
RC foam-built airplane assembly tip: Hot glued pieces can be de-laminated by applying over-the-counter pharmacy-grade 70% (or better) concentrate Isopropyl alcohol (not for human consumption!) to the weld joint using a soaked Q-tip(tm) AKA one of those cotton swabs glued to a paper stick thingies. The alcohol causes the hot glue to lose it's tight grip and the pieces separate! The process is used by us "foamy" airplane builders to re-glue parts back together when we make an assembly boo-boo... I use the technique when assembling plastic 3-d printed part joints... I hope this helps!
@imark7777777
7 ай бұрын
Well that's a new one, so hot glue in aviation then!
@theackshow5048
7 ай бұрын
That is RADIO-CONTROLLED MODEL AIRPLANES...
@WayneMoyer
8 ай бұрын
Since you made Twike the company aware of this. Let's see if they would want to see the upgrades you did.
@SianaGearz
7 ай бұрын
Their willingness to see the upgrades is countered by their likely unwillingness to cross the ocean on a Twike.
@agingwheels
7 ай бұрын
I've been emailing back and forth with them. They're a great group of people!
@sirBrouwer
7 ай бұрын
@@SianaGearz they could try to make a Twike version of a pedal boat. It would not be that much different. I don;t know if it is smart to use it on more then a pond.
@SianaGearz
7 ай бұрын
@@sirBrouwer I think it would be a rather smart thing to do, they might attract some Starnberger See resident customers with deep pockets.
@sirBrouwer
7 ай бұрын
@@SianaGearz I know that the Dutch navy is in search of a new boat. and we can cycle as the best.
@Silverfoxwolfen
7 ай бұрын
Gotta say I'm an automotive engineer and I utterly love your videos. You are dedicated and slightly mad, YOU ROCK!
@Tivoliterror
7 ай бұрын
For a permanent fix to the black paint on canopy, use windshield replacement primer, it's black and it's perfect for acrylic.
@Pho7on
7 ай бұрын
Yeah, I was wondering why he didn't use that. Maybe it eats at polycarbonate or causes it to craze?
@agingwheels
7 ай бұрын
The use of regular rattle can paint on the canopy was such a rookie mistake. As soon as I did it I wondered what I was thinking
@Tivoliterror
7 ай бұрын
@agingwheels a learning experience I would call it, looks great with the tape though, gives it contrast and fitting with the age of the vehicle 😀
@lateefcarrere1649
7 ай бұрын
You're really too hard on yourself; this is something a lot of us wouldn't even attempt, but you charge right in, and if I'm honest, it turned out great. As usual, I look forward to the next project that finds itself in your shop👍
@pinecone606
7 ай бұрын
@@agingwheelsmany spray paints can degrade polycarbonate, making it brittle and crack over time - I'd keep an eye on that long term if you aren't already doing that
@garygary4856
7 ай бұрын
Glad the " crash " was no big deal, but I LOVE the look of panic on his face !! 😂😂😂 I got a good laugh. Thanks
@quantumphaser
7 ай бұрын
That shelf was worth the effort. It's beautiful and functional. I can totally see spending 3 weeks on it, that's just the way custom projects go
@phenomanII
7 ай бұрын
For weeks I put off mounting some table legs on the back of my table to keep it further from the wall. I had to use a holesaw to remove the mounting plate edges without weakening the structure, then find a suitable wood screw and some little touches. Somehow it was finished mere minutes of work later. I am highly suspicious of them. There's just no way it went so smoothly.
@LongPeter
7 ай бұрын
It makes the whole thing look even more like a tiny, retro-future yacht.
@6reve
7 ай бұрын
Aye, though I don't understand why he hinged it instead of just making it two pieces with a simple joint in the middle
@GeekGarageDK
7 ай бұрын
Hope Twike reaches out again and will help you identify what you can delete of that massive old charger box so you only have what's needed.
@tuoppi42
7 ай бұрын
Windshield wiper.. I've used Rain-X and similar products for motorcycle helmet visor with good results. Should reduce the likelihood of never needing that wiper.
@Dimondminer11
7 ай бұрын
Yeah that stuff is actually insane. When I first put that stuff on my 99 grand cherokee's windshield I didn't need to use my wiper at all above 50mph.
@crackedemerald4930
7 ай бұрын
@@Dimondminer11 He'll just need to drive faster than 50mph while raining!
@jackielinde7568
7 ай бұрын
SUGGESTION: I know this comment comes too late to save Past Robert from disaster, but maybe Future Robert can use this. (Because we all know Future Robert will find another project where he will need to build a new battery module.) WHEN YOU HAVE A LARGE PROJECT WITH A HIGH LIKELIHOOD OF SCREWUPS, use some markers to create a visual indicator of orientation and polarity. My suggestion would be to grab two markers (one red and one black) and color opposing corners of each module before a single bead of hot glue is extruded. If we grab a six-sided die and assume that the 1 face is the positive plane and the six face (because they're opposite of each other on a die) is the negative plane, the corner where the one, three, five faces meet gets a red corner big enough to see, and the two, four six face corner gets a black coloring. This should add minimal time to the project and be easy enough for a Tired, Overworked, Sleepy Robert to do with minimal screwups. BTW, this isn't an original idea. Doctors will go into a patient's room with a sharpie, and have the patient mark the area that requires surgery to avoid screwups. After all, it's much harder to reattach a leg that was wrongfully amputated than it is to get the correct leg marked ahead of time. Turns out, this simple little trick has VASTLY cut down on costly screwups in the OR. Much more costly screwups than hot-gluing battery modules in the wrong orientation.
@captainvector
8 ай бұрын
A project that took more time and money than anticipated?! Inconceivable!
@jeebusk
7 ай бұрын
I had a supervisor who said If you want a good estimate (take your best guess and) multiply by 3, If you want a scientific estimate multiply by pi
@CaptHollister
7 ай бұрын
These videos in which Robert takes something complex and electric and then fixes and improves it are some of my favourite. Taking complex things and breaking them down into simple (sounding) steps is surely a sign of genius. The joy and fear during the test drive were a bonus... Must always remember to not panic.
@bc7444
7 ай бұрын
I'm now really interested in what the 'normal' amount of twitchiness is for the steering. I'd like an update on what you try and how much/little it improves things. Missing out on making a video for the mahogany shelf is unfortunate; it would have been great to get a new Under Dunn.
@agingwheels
7 ай бұрын
You'll get an update on the steering and some other final touches in a little while! About two days into the shelf I realized I should've been recording the thing. Oh well.
@93Martin
7 ай бұрын
At least the videos you DO make are friggin awesome :P Much love!!!@@agingwheels
@ryanokeefe12
6 ай бұрын
Hey mate, FYI - a spray of IPA well release hot glue almost immediately. I don't know the mechanism that makes it work, but it works. The best thing is; as soon as the IPA evaporates, the adhesive strength returns. This means you don't need to worry about neighbouring joints being weakened.
@MadcapMachinations
7 ай бұрын
I have to say I really enjoy the fact that you show your screw ups during the process. It shows that yeah mistakes are part of the process and no matter how long you do this for its perfectly normal.
@juanmiguel2636
6 ай бұрын
That shelf is nothing short of a masterpiece. Good job on that.
@generaldisarray
7 ай бұрын
Quick tip for the canopy, use butyl tape to glue it down. Butyl tape will hold it in place, however, unlike sealant/glue, butyl tape will not set up and will remain pliable allowing for differing expansion and contraction between different materials. It's also a lot easier to apply as it's a tape, but can be molded as needs be. I'm a butyl tape convert.
@Dimondminer11
7 ай бұрын
Wait butyl tape acts as a glue? I didn't know this that would be so much easier to deal with than standard sealant.
@generaldisarray
7 ай бұрын
@@Dimondminer11 they've used it to stick body kits, spoiler, etc onto vehicles for years. It'll bond to both surfaces but never totally cures, so remains flexible
@Dimondminer11
7 ай бұрын
@@generaldisarray wow i never knew this. That will help me quite a bit when i go to do some resealing on my camper
@generaldisarray
7 ай бұрын
@@Dimondminer11 top tip wear gloves. It's seriously good, you can use it straight off the roll, or you can squeeze it together like plasticine and squeeze it into panel gaps to seal them.
@jeebusk
7 ай бұрын
@@generaldisarray is that the same as what used to be used on windshields? I've used it but don't remember
@Kisai_Yuki
5 ай бұрын
This was actually fascinating. Reminds me of the kinds of "We can rebuild it, we have the technology" phrase.
@mitchgross592
7 ай бұрын
There’s something deeply satisfying in watching you piece by piece address the stupidity in design you find in these oddball machines. The Butt Switch is rivaled only by the jumper shutoff cable. Twike rivals Coda in lousy electric vehicle design. Love these videos.
@chatboss000
7 ай бұрын
What's the issue with the jumper shutoff cable? The only takeaway I got is it was dismissed as vestigial incorrectly in the process of implementing a new system. You don't have to program a relay for the old solution...
@mitchgross592
7 ай бұрын
If this was a completely homebrew project it would be one thing, but if you recall from the other Twike video this thing sold for $37K or more. For that I’d like a slightly more polished, less janky solution.
@theflyingfish66
7 ай бұрын
So many head scratcher decisions with the Twike. 1. Why is it a delta trike (single wheel in front) with a massive, inefficient boat-tail? It should be a streamlined tadpole trike like the Aptera. Delta trikes are just terrible in general 2. That tiller steering is horrendous. Normal bike handlebars would have been far superior. 3. On that same note, the backpedal brake is terrible as well. Should be a hand brake on the tiller or handlebars.
@mitchgross592
7 ай бұрын
It definitely feels “drawn” rather than “designed.”
@2008tourer
7 ай бұрын
I love you Rob, the way you explain things, the way you make mistakes and learn from them to create absolute masterpieces - it's all just amazing. Please never change
@yorgle
7 ай бұрын
You can also detach hot glue (at 10:00) by saturating the glue in isoprpyl alcohol. it somehow just releases the glue's bond.
@CRC.Mismatch
7 ай бұрын
I was about to comment the same! Good to see I wasn't disappointed by my fellow viewers 😅
@Avetho
7 ай бұрын
From what I can tell, isopropyl sucks the moisture out of hot glue (ethylene-vinyl acetate) and causes rapid aging of the adhesion surface. Hot glue when it ages starts to lose its adhesion, so like using coffee on paper makes it look old, isopropyl ages the adhesion contact surface so that it just comes off.
@yorgle
7 ай бұрын
@@Avetho Neat! thanks!
@Lizlodude
7 ай бұрын
@@Avetho Alcohol is also really good at wicking into tight spaces, so it likes to seep in more as it opens up a gap. Also works for getting 3D prints off a solid bed; put a bit around the rim and as soon as you can pry up a little bit it seeps in and detaches the rest.
@Avetho
7 ай бұрын
@@Lizlodude And that would be why isopropyl also dries out skin so damn fast, it wicks into the pores and dries them out! Its funny, I never made the connection even after researching how EVA reacts to isopropyl, I'd have thought my chemistry-specialized mind would pick up on that quickly, but nope :P
@gravelrhoads
7 ай бұрын
I love watching your videos. Not just because of you're knowledgable fun-ness, but because you're not afraid to show mistakes that you make and how you correct them. I've always believed that you learn more from mistakes than from doing everything perfectly.
@franklinmaurer8383
7 ай бұрын
It was so satisfying watching your 12v battery slide into the home-made battery tray smoothly due to it being such a perfect fit. Well done on this project! It's a quirky car that fits nicely with your other odd vehicles.
@NatzulForrester
7 ай бұрын
This video was perfect. The content, your self deprecating humor and technical expertise, hiccups and successes are presented in an incredibly entertaining and educational way. Excellent content!
@_AvaGlass
7 ай бұрын
9:22 That editing with the snap was so smooth. I rewatched it 4 times.
@graemefeeney2256
7 ай бұрын
Hi from Australia 🇦🇺 I stumbled across your channel due to a video on Ryobi Ride on mower info. I thoroughly enjoy the way you present your content. With humour, mistakes made and your knowledge. So now I’m just binging your content, knowing very little, but hoping to learn something whilst being entertained. Great job, I’ve subscribed and added likes. Today I learnt about Twike, that driving footage was entertaining & hilarious.
@duckdog8052
7 ай бұрын
love that mad laughter at needing to plug the twike into itself to get it to work
@vailpcs4040
7 ай бұрын
The second he showed the single ground wire, it was obvious what they did. I've used this for safety systems where I knew something had to be electrically isolated from external power, but seeing as the 12VDC is always on, this *should* have been done via a relay in the first place (as Robert added). My guess it they were trying to keep costs and installation ease down with later 110/220 dual charging upgrade.
@SimplyDudeFace
7 ай бұрын
I love that you are these projects on cars that I will probably never see in person, let alone own. Knowledge for its own sake. Love it.
@jumpjetcaptain495
7 ай бұрын
Hi, I recommend you spray Pledge (for different surfaces model) on your whole windshield. It works wonders to dispel rain and may even protect the windshield from the wiper scratching it. I use Pledge on my aircraft windows (glass and acrylic windows) and it works fantastic.
@travisash8180
7 ай бұрын
Would Mr Sheen work ?
@Enderdragon91
7 ай бұрын
@@travisash8180If it has similar ingredients it should. The ones to look for are the sulfactant Pledge uses (Alkyl Polyglycoside) and likely the corrosion inhibitor (Dipotassium Phosphate) as those seem to be consistent across the aerosol and squeeze spray versions.
@greggv8
7 ай бұрын
Get some N3 Nano and try it on a sample of acrylic. It's a super hard coating most of the epoxy+wood table builders on KZitem use. So it doesn't wreak havoc on epoxy... What about other plastics like acrylic, Lexan/polycarbonate, Delrin/acetal, urethane, polystyrene?
@lrich8181
7 ай бұрын
Have you tried Plexus spray? It is made for protecting aircraft windows. I use it to keep my headlights from fading.
@Matticitt
7 ай бұрын
I love that the people from Twike watched and responded to your video.
@a-aron2276
7 ай бұрын
That battery was terrifying, I didn't notice the lack of BMS connections, what I did notice were all the series connected batteries that weren't separated. I obviously don't bother with the paralleled cells but not to separate the series is asking for trouble. But the BMS is far more important especially given the battery voltage. Surprised you did the same. Otherwise absolutely savage work don't take my comment the wrong way.
@mjp0815
7 ай бұрын
Yes I agree, series connected cells that are just separated by two layers of shrink tubing, in automotive applications... I had these type of packs short out on me before in electric scooters, near miss, lots of smoke.... Best to use the plastic separators if the packs will experience vibration during their service. Awesome vehicle though, hope you have a lot of fun with it. Shame on Trike that they shipped their own battery like you found it. No BMS and very bad cell to cell isolation.
@Rom3_29
7 ай бұрын
29:00- Mr. Benz must been similarly terrified, when he tried his three wheeler one cylinder Benz car first time back in 1886. Absolutely excellent work upgrading and fixing your Twike. Maybe upgrade tiller steering with something safer?
@gannas42
7 ай бұрын
This is a pretty quirky vehicle! I'm anxious to see what happens with the steering. So even if this wasn't worth it... it was a joy to watch. Glad the accident wasn't worse! Thanks for the fantastic videos, as always. I still don't understand the whole time travel thing and how you avoid most paradoxes but that is small potates. 😂
@trevorjenglish
7 ай бұрын
For the paint peeling back and the glue bead- one thing I've done in the past with similar issues on windshields is take some gloss black vinyl and strategically place it on the outside. If you do it right, it looks like it was supposed to be there and completely covers up any mistakes on the underside. Edit: I see you did it! Good job
@rav04o2
7 ай бұрын
The beauty of working with hot glue is it can be removed with isopropyl alcohol. Since you’re working with battery add little bit at the time where a glue is touching a cell. If I remember correctly it works with high strength hot glue as well
@jovice9867
7 ай бұрын
You speak English. I speak English. Yet for 95% of your vlog, you might as well have spoken Dutch. The bits I did get ? Enjoyed alot. Seriously with your knowledge. You should be making serious money. Hope you are. Good luck with the Twike and try not to die. Cheers
@Maddiedoggie
7 ай бұрын
I think it would be appropriate to say that the Twike is the only 'muscle' car hybrid. I'll see myself out.
@Not31337
7 ай бұрын
I loved this video! I only partially understand the electrical bits (because I don't need it anytime soon), but you make it so interesting. I'm not exaggerating when I say that I look forward to your videos. Thanks!
@jeraldjoyce2995
7 ай бұрын
in all fairness, that IS a really nice shelf. the staining you chose looks really good w/ the white.
@beingboston
7 ай бұрын
Amazing job Robert! Love the passion, craftsmanship, technical skills, and dedication.
@profrumpo
7 ай бұрын
A long Aging Wheels video, excellent a mug of tea and biscuits (cookies) required. Robert, don't ever change, your crazy projects are pure gold👍 Oh and so good to see you proudly wearing a Festival of the Unexceptional T-shirt 😊
@stephengreen3566
7 ай бұрын
We appreciate your "sacrifice" working on and restoring this quirky little trike. Thanks.
@GreenJimll
7 ай бұрын
Good work, and I really like how you come across as a mechanical Timelord jumping back and forth between past and future versions of yourself, the project and even whole videos.
@Kaptain13Gonzo
7 ай бұрын
Over thought, over designed, over fixed, over spent and over the top. Yup, I'm watching Aging Wheels. THIS is everything I anticipate from your channel. The thought and work you do amazes me. All packaged with a chuckle. Thank you to past, present and future you!!.
@markfrye9178
7 ай бұрын
I understood about 0% of the electronics you spoke of, but I had to keep watching for your humor! Good stuff.
@graemefeeney2256
7 ай бұрын
This is me agreeing 100%. Just found this guy & he’s entertaining & addictive.
@mackprice6167
3 ай бұрын
Anyone realise he said rear rindow at 2:30 i just noticed. Its kinda funny aha. Great vid love em
@alfawhiz
7 ай бұрын
You truly are a modern day hot-rodder. It used to be nuts, bolts, ported heads and hot cams, now it's hot glue, wires, battery packs and electronics. Well ok, some nuts and bolts too :) Keep it up, can't wait for the next one!
@stevethepocket
7 ай бұрын
It's always amusing seeing the random gaps in people's knowledge. I spent this whole video watching you build a complex battery module that I wouldn't even have a clue how to _touch_ without killing myself, and understanding only a small fraction of the explanations of what you're doing, but then you got to the part where you accidentally hot-glued something together the wrong way and had no way to take it apart and I was like "...I'm 90% sure there's some very common household chemical that will melt that glue like butter; how does he not know this?"
@nickl2625
7 ай бұрын
I remember being a passenger in a friend's Twike, it was the most terrifying experience of my life, and I've done a lot of dumb stuff. The steering is lethal and everything about was painful to my engineering sensibility. How they are still in business I have no idea.
@eekee6034
4 ай бұрын
The designers must be both crazy and high on 60s futurism, and then some. I mean, I fit that definition, but I'm still not insane enough to put that design into production. I watched AW's other Twike video and this one back to back, and my opinion of the Twike just kept on going down. It briefly went up when Robert said Twike sent him a list of things which could fix the steering, but then I saw your comment and did some thinking. I'm not half the engineer I'd like to be, but drawing a parallel with analog electronics, I don't think you can fix a bad design with damping. Also, the sheer length of the list of steering fixes Twike sent Robert reminds me of software where a long list of features or tweakables can be a sign that a different design would be much more suitable.
@HRDBMW
7 ай бұрын
I absolutely love the Twike. I have always loved them. Im just glad that now there are ones old enough to import.
@xungnham1388
7 ай бұрын
Depending on how much hot glue is involved, a lot of times you can break apart hot glue bonds with cold, especially if theres a large difference of thermal expansion between the hot glue and bonding material. Try throwing the battery pack into the freezer and then doing a quick snapping motion. If that doesn't work, you can try localizing the thermal expansion more by concentrating cold on just the glue by turning a can of compressed air upside down and getting the liquid propellant onto the glue.
@drybread1146
7 ай бұрын
I love how you said "It's done now" and then list reasons it's not done. Because I do that all the time! I think it just makes me feel better to say that it's done, when I really just mean "it's functional." EDIT: I just watched that part again and there's not really more tasks to do, other than testing, and maybe a few related things. I would consider that 'done' also!
@freman
7 ай бұрын
Squirt some isopropyl onto hot glue joints to break them, it might take a few squirts and some gentle massaging but it usually makes hot glue let go.
@jmcbike
7 ай бұрын
You might add active balancing- that will balance cell groups even when the battery is in use. I did that for my aging eBike battery, where one cell group has less capacity than the others. Gives more range with an imperfect battery. Nice job on constructing the battery and other improvements.
@14Elite15
7 ай бұрын
FYI in my experience using hot gule, you can release it by using 99% isopropyl alcohol as a mild solvent, it's not perfect but it does help a lot.
@TimothyFrisby
7 ай бұрын
I honestly find all of this EV nitty-gritty stuff fascinating, so this was a fun watch
@QALibrary
7 ай бұрын
I can not understand why did they not put the two steering wheels at the front with a wider back wheel for the go-forward bit - it makes the driving, handling and performance experience a lot better
@jakub.anderwald
7 ай бұрын
Electric car battery setup now seems so easy after watching a number of your video. Thank you for showing to the world that it's not just old carburated engines that are simply, electric cars can be simple and easy to maintain at home as well.
@densamme1752
7 ай бұрын
And now i want you to electrify a morgan three-wheeler to show that the correct trike is a reverse trike.
@samiamcas
6 ай бұрын
I've been watching your videos for awhile. A lot has changed but not you or your videos so thank you for being something consitent for me to look back to
@sixdeuces6825
7 ай бұрын
The 12V battery tray was elegant. Same with the folding shelf. Nice work!
@MooseOnEarth
7 ай бұрын
Epic work. Greetings from Germany, where this vehicle was developed and built.
@EdwardGordington
7 ай бұрын
13:27 the "aww that ones all weird" gave me a good chuckle lol.
@Dv_Null
7 ай бұрын
Real question is, did you have fun? And to me, it looks that way. Thank you for sharing this. It was rather enjoyable to watch.
@smarouchoc7300
7 ай бұрын
Love this. And the reason it has twitch steering is, the Twike is built backwards. Should be a tadpole configuration , two wheels that steer in the front, and a fixed wheel in the back. I don't care what adjustments Twike has you make, you aren't going to be able to make it as safe and stable as a tadpole configuration.
@harriettanthony7352
7 ай бұрын
VERY TRUE! Now Robert can fix that issue!
@SianaGearz
7 ай бұрын
Is there a vid or written article or book chapter with graphics which explains why it is so?
@happytorrentt4500
7 ай бұрын
Spray paint in a cup/lid and a roller brush is how I fixed my acrylic f-ups while restoring old subwoofer boxes. The back shelf looks great, now the twike needs some chrome accents to match lol
@viewhero3158
7 ай бұрын
The Twike batterypack is even safer than you think. These are cells specificly designed to be save without BMS. Each individual cell has a mechanical savety- valve/switch, which disconects (sadly permanently disables...) the cell when overcharging. But you are still right, this is a technologie from the past (around 2010 ?), when small companies struggled with the affortability of customised BMS. The drawback was, that the Cells were quite expensive and of less capacity (they were also very carefully produced to minimise the drift and prolonge the livetime) than other "less save" cells of the time. And even thought it is quite unlikely these batteries burn even in case of faliure, in case of faliure, a whole pack dies resulting in the need to replace quite a lot of these expensive cells. Glad to see your solution, great work! I am a big fan of the twike (rented one for a week around 2010), but never had the money for it and to be honest, it in that time always struggled with construction-deficiencies resulting in quite a lot of neccesary maintenance. To be an economic vehicle, you should be good in mechanics and electronics...
@DeuxisWasTaken
7 ай бұрын
You pull off being informative and entertaining at the same time really well, this was a pleasure to watch, subbed.
@arizona-4734
7 ай бұрын
Robert, we who have been watching for any length of time KNOW there is no such thing as a quick side quest with you. Also, that you over engineered and over spent on something like a Twike is why we come back. Keep doing what you are doing even if it doesn’t make sense. Some people waste more money in far less interesting or productive ways.
@MontegaB
7 ай бұрын
I love your channel man. Every video you make is consistently great. I can't even imagine how much time & editing goes into producing these, and you do great work. Thank you!
@eekee6034
4 ай бұрын
KZitem has been showing me the thumbnail for this one for weeks, but has only just offered me the previous video with the twike review. I'm so glad I watched that one first, because now I can entirely understand why you crashed it.
@AATTPP1991
7 ай бұрын
I love that you full add in your “learning curve” moments, because we all go through them and usually there’s a lesson to be learned in some capacity, so sharing is helpful! Keep up the good work!
@DestDroid
7 ай бұрын
I absolutely love this channel. Fantastic. I can't believe you kept pedaling after feeling the steering on the road. I would've stopped right then and there.
@adhdmc
7 ай бұрын
I love all your videos but the build ones are my favorite. Stoked to see you working on projects again.
@kaitlyn__L
7 ай бұрын
That was some mighty fine masking around the other batteries. I had to watch it a few times to figure how you kept the one take with clicking your fingers - and figured it out when I noticed only one pack has moving reflections in the heat shrink 😊 that’s a super subtle detail though. Very effective for a quick moment.
@RadioSaladStudios
7 ай бұрын
Twike needs to have you on their development team. Genius stuff.
@rustywrx
7 ай бұрын
Of all the KZitem channels I'm subscribed to, there are very few I watch without skipping through.. Yours is one of the few 😄
@AndyWicker
7 ай бұрын
Black silicone around inside edge of rear window, just to make the edge look nice. Cool video!! You speed things up at JUST the right times.
@junkerzn7312
7 ай бұрын
What a huge amount of work, but you got it operational in the end! And that original battery not having a BMS/balancing-leads... that was insane. It's hard to imagine any company doing something that virtually guarantees a pack failure (and possibly a fire) down the line.
@klatubaradanikto
7 ай бұрын
I like this video better than the other one. I think you made the correct choice in introducing us to the Twike in it’s complete form though.
@perplxxd
7 ай бұрын
i did NOT expect Twike to actually send you an email concerning your steering, that's really cool.
@Chrispy9393
7 ай бұрын
this thing is nutty. good work. that shelf is BEAUTIFUL!
@makostesztakft
7 ай бұрын
That buzzer on the turn signal is actually a thing on buses (over heresville it's a thing on Gillig buses, albeit short, but I've heard it on Solaris trackless trolleys the last time I was "back east" in Hungary). Speaking of silly European tech, I'm now wondering if the two-step throttle switch is supposed to do the old-style SiFa scheme-which the Hennigsdorf-built MX (read M10) cab-motors for the interurbans around Budapest have too. Push the plunger all the way down to step the power controller (20+3-step servo wheel to cut-in various resistors via contactors) forward, middle step to hold the current "notch", and release to step back towards coast. Digital implementation is hard to clock, I imagine, but that might be it; "half beans" and "full beans" just seems less plausible.
@timpsensky5181
7 ай бұрын
I'm just impressed you have a project done and running.
@andreasbayer
7 ай бұрын
Great new addition to your collection! I randomly see one in yellow here in Stuttgart, Germany on the roads. Knowing how it is steered and driven just makes it even more goofie than I thought... But he (or she) just keeps driving it through Stuttgart city traffic...
@VencelBiro
7 ай бұрын
This was maximally entertaining to watch. Hope you recover some of the costs and continue making these amazing videos!
@ericsevern
7 ай бұрын
Despite the costs in time and money, your work is still greatly appreciated by us. To us, there was no waste.
@TwoWheelWarrior
7 ай бұрын
Every Twiker is a hero. Helping save the world One pedal revolution at a time.
@durdlegerg7231
7 ай бұрын
Your videos simultaneously make me believe I could do some of this myself, and make me feel I never should be allowed to attempt to do such a thing. Thank you for letting your audience live vicariously through your shenanigans.
@zaprowsdower9471
7 ай бұрын
Kapton tape is typically used to secure battery packs together, 12:37 . Its high temperature characteristics and superior insulation ability make Kapton tape a preferred choice. Also, generic ABS plastic, 12:03 , when exposed to high temperatures can combust and emit toxic fumes.
@316hightimes
7 ай бұрын
Thoroughly enjoyed how you have presented this machine in both videos. I had no idea Twike was a thing. I really wanna buy this when you are done filming. I'll wrap it in chrome to look like "max" from Flight of the Navigator while i ride residential streets to get the aircraft hanger I work at... probably just on fair weather days. If I took the bike trail nearby I would likely end up in the river at some point.
@dustymccraw7715
7 ай бұрын
i enjoyed the video. it's immensely entertaining to see odd vehicle repair (mistakes and all). keep up the good work. 👍😃
Пікірлер: 1,3 М.