Great video mate! I’m just glad you mentioned the cylinder number and said which way they’re numbered lol. I’m not thick on the spanner’s usually but I know the firing order and cylinder layout are different on the french motors sometimes. My 2012 focus has a number 2 injector issue too and I couldn’t fathom whether number 1 was on the left or right. I’m following your lead as 1 is on the left. By the way,great tip cutting that insulation,saved me a bucket of pain getting to the built! Keep up the great tutorials pal👍🏻
@florinbargaoanu5556
2 жыл бұрын
I own an 2012 ford focus with the same error exactly on the same injector.I tested with forscan to find out why motor is starting to shake bad .In a few days i will go to the mechanic in order to resolve the problem.Thanks for the explanation here, because in my situation i will go with my homework done to the mechanic,to know what is dooing to the engine
@gabrielpefcik570
Жыл бұрын
Number 1 cylinder from gearbox, pal
@simonedwards1653
Жыл бұрын
It certainly is having worked with Citroën's with this engine for a long time cylinder one is flywheel end (gearbox) ,👍
@razvanturcu9871
Жыл бұрын
This is what I wanted to know. I wondered wheter the numbering is from gearbox or the otherway around, considering that for peugeot the exact same engine has the numbering starting from the gearbox.
@petegoldsmith4007
7 ай бұрын
Differs from model to model. I’ve had this engine in a Focus and in a Peugeot, & using Forscan (the ford software) it’s labelled 1-2-3-4 & in the 3008 it comes up differently.
@demolitionman3991
23 сағат бұрын
Good video but I’m using iCarsoft diagnostics . I’m unable to change injector codes . Any advice . I’ve erased learned values and driven 19 miles seems to be running good but I’m annoyed I’m unable to change injector codes
@bart60
5 жыл бұрын
great video, thank you. Which tool or software can I use to diagnose my injectors ? I have a Ford Grand Cmax 2011 1.6L
@adamcinematic9499
2 жыл бұрын
Hello, many thanks for your sharing video. It helped a lot, but I ran into a problem after the exchange. After replacing the injection with a refurbished one, the injector now knocks. Can you please tell me how many NM you tightened the injection holder on. Or do you have no advice on what could cause this knock after the injector replacement? There was no knock before the exchange. Coding new one is done. Thank you
@vladimirantoniu2754
2 жыл бұрын
I have the same problem,how did you fix it?
@adamcinematic9499
2 жыл бұрын
@@vladimirantoniu2754 hello, in my case the problem was, that i was need to replace one more injector ass well.
@mariusvfp
5 жыл бұрын
Help. How many newton meters apply on the screw
@tundrasheep
6 жыл бұрын
Thanks, great video ! subscribed !
@tadeusz6061
Жыл бұрын
After I had some issue with my engine power my mechanic changed one of my injector, after one year the issue returned so I add liquid moly to my diesel and after one month I decided to check if my mechanic changed the code in ECU, and I found that he didnt, so I changed the injector number in ECU by myself to correct numbers, and what I probable made wrong I restarted all injectors. After that the engine in my Ford C max 1.6 tdci is not responding. I know that I have errors in 1 and 4 cylinder low pressure, the third injector was substtitute by my mechanic, I kmow that injectors works in pairs, so I suppose I have foulty injector 1 or 4, and I changed code of 3 rd injectors. I am about to clean injectors, I hope they are not all need to be removed. Is it worth trying ? Should I now remove all errors from the ECU ? or wait until I clean injectors ? By the way, I am plumber not mechanic.
@koceilaamzal9005
4 жыл бұрын
hello, I really like your video. however I have a ford focus from 2011 and I have the fault codes: p0135, p02d3, p02cf, p02d1. do you know what the p0135 code corresponds to (it seems to be the lambda sensor but i don't have this one). should i change the injectors? cordially
@mercedesbenz9956
5 жыл бұрын
Nice video thanks! I have a problem on my 1.6tdci... After engine repair (pistons) the would start. I have checked every little thing on the car but still dont know why the car cranks en not start. My fuell injectors dont getting power at all and i dont know how to fix this problem. Maybe you can help me out?
@AC-sz7le
29 күн бұрын
Hello help needs what torque to tighten injector for 63 (2012) plate 1.6 TDCI
@bilaroghjoljonustudeild9782
2 жыл бұрын
What are the tightening torque and degrees specifications for the injector clamp bolt?
@GAH4444
2 жыл бұрын
27 nm
@guihen9194
9 ай бұрын
I saw for volvo and peugeot 4nm + 45 degrees with the same motor as in the video. Is 27nm a reliable value? It is quite tight. I tried several tightening 4nm,8nm and 13 nm and I have leakage
@swarajjoye
5 жыл бұрын
How did you remove the green plastic clips
@simoncsaby3073
Жыл бұрын
Mobile Automotive Service, can u tell me please the Injectors torque and the grade, the bolt's tight setting please. I need this Information ASAP because tomorrow I want to change the injectors! Thank you in advance
@igortomasek3490
5 жыл бұрын
Hi my focus mk3 has fault on all 4 cylinder injectors but car is in good driveable status and i can't see any problems only check engine.Fault codes are: P02D300,P02CF00,P02CD00,P02D100.Is this possible?My question is could i buy old injectors and replace them?Thanks
@Dasdembo
6 жыл бұрын
Good video!
@ozzzyyyyy
Жыл бұрын
If I just clean the injector and put it back do I have to program it again?
@huckfinn8444
Жыл бұрын
If its the same injector then no
@harshkhy
6 жыл бұрын
Error code P268A(Injector not programmed/calibrated) in Chevrolet CAPTIVA, please advice which tool & software will work.
@salmanahmed7805
5 жыл бұрын
Which code do i choose from the top of the injector? There are a few to choose from
@Firby1988
4 жыл бұрын
So how do you reprogram the injectors if you haven’t removed them but replaced the engine
@mobileautomotiveservices5461
4 жыл бұрын
If the engine management computer and injectors are the same you wont need to do any programming
@Firby1988
4 жыл бұрын
Mobile Automotive Services so we will need to reprogram because the engine and the injectors are different . Can this be done without dismantling the common rail ?
@mobileautomotiveservices5461
4 жыл бұрын
@@Firby1988 yes many generic scantools will allow you to code the injectors to the ecu. The long number printed on the cap of the injectors are all you need
@laulove4736
3 жыл бұрын
Hello can u tell us what is name of tour diagnostic plss
@Chingy8
7 жыл бұрын
Thank you for the informative video. I have a 2011 Mazda 3 1.6 diesel that has the same engine as the Ford Focus diesel. It has a P1262 error code suggesting a faulty fuel injector at cylinder 2. I was thinking of replacing the fuel injector and seal myself but your video suggest it would need to be reprogrammed. Do you think if the fuel injector is actually faulty and I replaced it myself, would the engine get out of limp mode and be drivable to the Mazda dealer?
@mobileautomotiveservices5461
7 жыл бұрын
Chingy The car will most likely be drivable if the injector is replaced, however you may still need a scantool to clear any fault codes that have put the car into a limp home mode. Also expect the engine to be hesitant/stumbling as the pilot and main injection maps will not have been reset.
@Chingy8
7 жыл бұрын
Mobile Automotive Services thanks Lee! Where is your business located?
@mobileautomotiveservices5461
7 жыл бұрын
Chingy Co Kildare in Ireland!
@gavinmcdonald583
6 жыл бұрын
Good video, I am about to replace an injector in a 1.8tdci focus. Does the system need primed/bled at all prior to starting the engine once the new injectors are in place?
@nirvana9610
6 жыл бұрын
hello, i've replaced an injector on a 1.6 116tdci and before coding it worked okish, but after coding it is not driveable, it idles really rough and cannot be revved because of the dieselknock sound. what should i do?
@simonedwards1653
Жыл бұрын
That's a PSA dv6c and the earlier dv6 and this dv6c engine and cylinder one is at gearbox end u know being a Citroën technician and know that engine well
@mikle65
Жыл бұрын
DYB T1DB1K 5DAAMC focus 1.6tdci dv6 2011/2, do you know which one is cylinder 1 on this one?
@simonedwards1653
Жыл бұрын
@@mikle65 same as the PSA gearbox end
@mikle65
Жыл бұрын
@@simonedwards1653 i had to unplug one injector then fire it up to see the open fault code and this car listing it as cylinder 1 from the timing belt side. this is when ford and the french stick their head together, a big pile of foggy indefinition, Even the ford dealer said program it to firing order over the phone! i had to check a newer focus with the same engine just to find it it is programmed from the flywheel side, same with a peugeot 3008. If in doubt, check yourself is the lesson for me. thanks for trying to help tough!
@nrlOO
6 жыл бұрын
Hi, i have reset fuel injector value factors even though i havent replaced new injectors. What happened now is that engine is working strangely, and cylinder contribution values changed on live data. I checked all the injectors and their values match the values in ecu, so what could be wrong ?
@mobileautomotiveservices5461
6 жыл бұрын
Your engine may have to run through a complete drive cycle before it runs as it did before. On many Ford vehicles, this can take a while, up to 50 miles of driving in different speeds/load profiles.
@nrlOO
6 жыл бұрын
@@mobileautomotiveservices5461 so it should be ok in a while ? Because my fuel consumption before was about 4.5 l/100km/h now it went up to 10-15 l/100km/, hope it all changes. Engine is making rattling noise.
@bartoszrybczynski9980
5 жыл бұрын
@@nrlOO After reset of injectors memory, you have to make an "learning" of injectors. You have to warm up your engine, go for a short trip, and few times speed up from 2000rpm to 3000rpm (on 3 or 4 or 5 gear), and then wait when engine will go down from 3000rpm till 2000rpm(without breaking) . You have to do it few times (7-10times) and then injectors should finish the procedure of learning.(injector learning show parameter, which name I don't remember, but range is 0 till 7, (which 7 mean full learned)
@David123598
5 жыл бұрын
I have smoke coming out of injection 1 .
@Jakelewis1991
4 жыл бұрын
Im guessing this is fixed now what was the problem mine started doing this today
@karu8588
11 ай бұрын
Its not clear
@MrDunkyg
7 ай бұрын
My diagnostic mechanic mate said you don't even need to reprogram in the new injectors so just plug and play the new or used one, simple, don't pay for a rip off mechanic for a two minute reprogramming folks
@mikle65
Жыл бұрын
Poor injector design...
@vd4169
10 ай бұрын
Poor fuel...
@mikle65
10 ай бұрын
@@vd4169 how my 18 years old diesel did 280k miles with no sign of an injector fault.
Пікірлер: 62