The Park Tool TW-6.2 is not designed to be used to loosen bolts. A breaker bar is ideal for removing bottom brackets.
@BrianVaughn
2 жыл бұрын
Ok
@Dialed1
2 жыл бұрын
Piano black, pairs well with the background sound track. Nice looking cranks!
@BrianVaughn
2 жыл бұрын
Thanks! I've been trying to hunt these down for a while.
@conorocon82
8 ай бұрын
Great video, Thank you. Pity Shimano dont provide the tools to fit the crank in that massive fancy box.
@mtbboy1993
2 жыл бұрын
6:22 I too do the same, 40 nm, I can't even go past that, I am not strong enough. but that would be overkill anyway. Never had any issues with 40Nm.
@mtbboy1993
2 жыл бұрын
The wear on the crank axle can be due to metal on metal contact with bad tolerances on axle or bearing. if the BB has a sleeve thing to protect the crank it won't happen as fast. But I've seen in a vid by Hambini, showing Sram GXP cranks where tolerances were really bad, resulting in this butt much worse. You probably don't have special tools to measure tolerances, he has special tools for it, i forgot the name of it. He has serval types of tools for measuring tolerances of various types. butt some things are so bad even a vernier would easily show bad tolerances.
@Lepercurtidoo
Жыл бұрын
Nice video, interesting... There where no washers /dust seals included with my shimano bottom bracket. Guess I'll have to go to my lbs, hopefully he will have some for sale.
@hoff482
2 жыл бұрын
Good stuff Brian.
@BrianVaughn
2 жыл бұрын
Thanks, Pat! It was fun.
@FantaFuture92
2 жыл бұрын
a torque wrench is not a breaker bar.. rip
@BrianVaughn
2 жыл бұрын
Got the job done
@FantaFuture92
2 жыл бұрын
@@BrianVaughnyep but i would not use my Hazet torque wrench for that lol. Would hurt my feelings
@BrianVaughn
2 жыл бұрын
It's a torch wrench that goes to 60nm. It can handle it.
@Flyanb
2 жыл бұрын
You didn’t try the elliptical chain ring??? I almost assumed you had one? My Dub BB always get Fowled between the small bearing hole and the shaft. I usually take it apart twice a year and clean it. I’m surprised you weren’t getting creaking? Mine look like yours, hard to keep clean!
@BrianVaughn
2 жыл бұрын
I've never tried an oval chainring. I might after this one wears out. I think the dust wipers make a difference when keeping the BB/crank clean.
@workhorsemtb7075
2 жыл бұрын
I've got the same crankset
@BrianVaughn
2 жыл бұрын
They do look really good!
@testtesttesttesttest884
Жыл бұрын
Holy crap that’s a nice way to damage a torque wrench
@BrianVaughn
Жыл бұрын
Amazing it still works and goes past the nm used to tighten it.
@markfenwick5441
Жыл бұрын
What is? Tightening a BB? Rubbish
@bikevlogadventure3263
Жыл бұрын
Nice...
@harrygrimley4352
2 жыл бұрын
That's cool Brian. I've never done that before. Interesting. Have you ever considered going to an oval?
@BrianVaughn
2 жыл бұрын
Thanks Harry. So I know people swear by them but it hasn't been something I felt I needed.
@harrygrimley4352
2 жыл бұрын
@@BrianVaughn I wondered. Cycle just did a short video on the difference.
@BrianVaughn
2 жыл бұрын
Yeah, it's one of those things that has it's pros and cons. If you give it a shot let me know how you like it.
@san_costa
2 жыл бұрын
great video, but do not use the torque wrench to loose bolts, you will damage a very expensive tool
@markfenwick5441
Жыл бұрын
He didn't. The BB drive side is reverse thread
@san_costa
Жыл бұрын
@@markfenwick5441 hey man, sorry but I don't think so, he removed the chairing at 3:24 minutes using the torque wrench! He should be using any wrench but torque wrench to lose anything!!!!
@BrianVaughn
Жыл бұрын
Don't worry guys, the TW 6.2 can handle all the things. That's why it's called a tool.
@san_costa
Жыл бұрын
@@BrianVaughn once again Brian, the tool is not for this purpose, however, the tool is yours, the money spent was yours, no more comments. Thank you.
@KrisYahner
2 жыл бұрын
What prompted the switch to new cranks?
@BrianVaughn
2 жыл бұрын
I was looking for a better experience and felt replacing the SRAM cranks would help. The rest of my drivetrain is shimano.
@mtbboy1993
2 жыл бұрын
@@BrianVaughn I am not sure why that would be needed, you only needed to use a chainring with an offset to suit, I recommend to use 6mm offset if it is feasible on your bike, not all boost frames can use non boost chainrings, so you have to use 3mm boost chainring. if the chainring suits the chain there should not be anything hindering a smooth experience. but offset also depends on the cranks, if the Sram cranks for example had the chainring be mounted too far out that would reduce performance.
@grumpy-dad3701
2 жыл бұрын
Newton meter. Nah I go by how deep my grrrrr is when tightening.
@mtbboy1993
2 жыл бұрын
7.30 In my opinion this is a stupid design, they sohuld have had the right crank arm come off, and be able to install it easily without taking the axle out of bb.
Пікірлер: 36