great job, I'm actually doing this job right now. did a search to check myself. Thanks...Scott
@WJeaimsess
4 жыл бұрын
Great job, thank you man!
@jesuirincon7194
4 жыл бұрын
Your intro got my subscription
@adamapostolos781
2 жыл бұрын
Thanks for explaining, appreciate the care for the pressure plate bolts... very helpful
@iowadiy6361
2 жыл бұрын
No problem, glad it helped!
@MOPARMuscleLEBANON
3 жыл бұрын
thanks for the video man , i have a 73 Charger 400 big block with 4 speeds , i have a bad vibration , thought it was the driveshaft it wasn't .i have vibration when i raise my RPM standing still , could it be the flywheel ? also i have a very stiff clutch pedal and vibrating when launching
@iowadiy6361
3 жыл бұрын
It could be something loose on the flywheel or clutch. I think that’s probably the first place to look at
@MOPARMuscleLEBANON
3 жыл бұрын
@@iowadiy6361 yes i posted an old photo of my engine before installing it and someone told that it doesn't have the pilot bushing and another friend saw the flywheel is not tighten to the max
@iowadiy6361
3 жыл бұрын
Hopefully that’s all it is and you can just tighten it up, install the bushing and then go
@MOPARMuscleLEBANON
3 жыл бұрын
@@iowadiy6361 hopefully brother keep up the good work love the videos greetings from Lebanon
@scottherbert4558
5 жыл бұрын
So I found the bronze bushing its ID is small the alignment tool wont fit , I am questioning the out put shaft will fit . So I am grabbing a re-emerging and opening the hole.
@iowadiy6361
5 жыл бұрын
There are several different sizes of pilot bushings. If it’s a large difference I’d just make sure to buy the right one
@scottherbert4558
5 жыл бұрын
I think the bushing was crushed .... thus making the ID small. I have a replacement bushings already. It fits the input shaft no problem.
@iowadiy6361
5 жыл бұрын
That would do it. Good thing you didn’t try to force it and make another problem
@paulgabby3750
6 жыл бұрын
I'm just a do it yourself-er... Wouldn't it be best to put the pilot bearing in first ? More room to work and less chance to get spooge on the flywheel. Thanks, nice job on the video !!
@iowadiy6361
6 жыл бұрын
Yes, that actually makes a lot of sense. I’ll make sure to do it in that order next time!
@ryanspradling9856
2 жыл бұрын
What size socket for the flywheel bolts?
@iowadiy6361
2 жыл бұрын
I think in my case it was 11/16. But every manufacturer can be different
@Milkmans_Son
3 жыл бұрын
The 1996 GM service manual is pretty clear: no thread lock on the flywheel bolts. Creates quite the dilemma.
@iowadiy6361
3 жыл бұрын
That’s interesting. I’ve only ever seen that thread lock should be used. The only difference I can think of between the early and late sbc for the flywheel is switching from the two piece rear main seal to one piece which changed the flywheel bolt pattern. Maybe they changed their stance at that point
@4marky
3 жыл бұрын
@@iowadiy6361 what color loctite were you using?
@iowadiy6361
3 жыл бұрын
I don’t recall. It was whatever I had on hand... which might come back to bite me later
@Milkmans_Son
3 жыл бұрын
@@4marky I used blue.
@-smp-scientificmethodpersp838
5 жыл бұрын
Should have kept that song going
@unclequack5445
6 жыл бұрын
Why not fix the oil leaks?
@iowadiy6361
6 жыл бұрын
I’m not really concerned with a spot on the floor and I check the oil every time I fill up with fuel so I’m not worried about it getting low. I’m also building a new engine for it now
@unclequack5445
6 жыл бұрын
Looked like a valve cover leaking down, or the rear main seal. Nice truck.
@rickyrogers4173
Жыл бұрын
What’s the part number for the flywheel?
@iowadiy6361
Жыл бұрын
I do t have that. I just got it from O’Reilleys. It’s a late block so it’s a one piece rear main seal too
@Tony-tk4ht
2 жыл бұрын
Should it spin inside?
@iowadiy6361
2 жыл бұрын
No. A bushing should not spin inside the crankshaft. The input shaft of the transmission will spin inside the bushing though.
@donkeydiehard879
6 жыл бұрын
I think it's worth mentioning that the pilot should be pressed all the way to the lip. Reason being, that insures the pilot bearing is true and straight. Its press fit so it can be close but you're talking about thousandth of an inch that matter in this instance.
@iowadiy6361
6 жыл бұрын
Yes, sometimes that extra thousandth of an inch can be the difference to be within tolerance or not. That would be a small mistake that would take a lot of time to fix!
@tonycantu2863
3 жыл бұрын
If using a pilot bearing which way do the needle bearings face towards the block or away?
@johnmilner7603
Ай бұрын
You never put grease in a pilot bushing cause they are self lubricated.
@molo9256
3 жыл бұрын
What's better a bushing or bering?
@iowadiy6361
3 жыл бұрын
Newer transmissions will typically use a bearing but older ones used a bushing. A bushing is very forgiving and will last for me as long as I have the car so that’s why I use a bushing
@molo9256
3 жыл бұрын
Thank you.
@tonycantu2863
3 жыл бұрын
@@iowadiy6361 which way should the needle bearings face ? Towards block or away I can't seem to find out even on Prodemand.
@iowadiy6361
3 жыл бұрын
I’ve never used a needle bearing, but if there’s a flat side on the bearing that would be meant to be pressed in flat against a surface. A round side would be on the outside
@georgecummings3227
3 жыл бұрын
Bearing any day.
@yz250a
6 жыл бұрын
Do not grease Oilite bushing!
@iowadiy6361
6 жыл бұрын
I’ve heard it both ways and I understand the logic behind both thoughts. I’m not sure which one is right, but I haven’t had a problem yet with adding just a little bit of grease
Пікірлер: 45