Thank you very much Shawn!!! It was very halpfull. Good luck!!!
@Giratina_
6 жыл бұрын
Hey, thanks for posting! My engine decided to fail :( and this will hopefully help soon!
@StrongFarms
2 жыл бұрын
Update! The jdm engine we recieved had a different lower engine Mount bracket. The axels wouldn’t clear, you need to change over the bracket to the US version
@gilbertmarquez6434
Жыл бұрын
Thanks for posting!
@brunom1280
11 ай бұрын
Did you have to get a different ecu for the jdm engine?
@octagusjohnson3707
2 жыл бұрын
That part under front windshield that you pull up come off to get four to five more inches
@jbmotorcoscotland1639
7 жыл бұрын
Just about to do this job - where did you attach the chains for removal?
@waltstephenson7176
4 жыл бұрын
I wish you were in TN I need this swap done
@shawnh9677
4 жыл бұрын
tennessee jdm motors is a great place to buy these engines as well. they do installations also.
@streetbikebilly2597
2 жыл бұрын
Anyone know if the jdm ebay engines are the same as the us r18s but in stick shift? I'm looking at getting one from a stick model to swap so it already has the flywheel
@kevinstafford9466
2 жыл бұрын
I wish I would have known about the throttle body. The idle can’t adjust properly and it throws a check engine code. Sure would have been a lot easier to swap it when the engine was out.
@mrdiaz2575
6 жыл бұрын
Hey men do you if it’s possible to do a k20 swap?
@ionelaioni6355
Жыл бұрын
Piston rings for r20 are the same with k20 engine?
@user-kp4sn9bs2r
7 жыл бұрын
Thank you!!! Did you check the compression before instaling? And how to make shur that the new engine has no crack on the block of cylinder, because all sellers have washed engines before selling.thank you
@shawnh9677
7 жыл бұрын
No i never do. I have installed about 25 of these engines and have never had a problem with any of them. They always fire right up with fresh oil and a new oil filter.
@StrongFarms
2 жыл бұрын
So for a manual, what all is different?
@beezowdoodoozoppitybopbopb9488
2 жыл бұрын
I cant seem to find anywhere, but do the jdm blocks have any reputation for cracking like the usdm blocks? If not then I'm gonna start keeping my eye open for a car with a bad motor and then pick up a jdm swap
@jondoe2099
7 ай бұрын
A year late, u might have different car.. but go for 2010 and up.
@user-kp4sn9bs2r
7 жыл бұрын
Hello Shawn! I would like to buy the same engine, because i got crack on my engine block 2007 EX. I have manual transmission on it. Is it a different connection to engine for automatic and manual? I mean if i will buy only the engine. Thank you
@shawnh9677
7 жыл бұрын
nope it is the same engine you will just have to swap out your flywheel off your old motor to the new one.
@kirbinipales4812
4 жыл бұрын
Question, I bought the same JDM motor. How did u convert the ac sensor? The US one has 3 pins and JDM has one. Pls let me know thanks!
@shawnh9677
4 жыл бұрын
Use your US harness and your US ac compressor.
@kirbinipales4812
4 жыл бұрын
Thanks for this video man. I couldn’t find any other videos that did the whole swap including motor and tranny. I ended up rewiring the ac compressor sensor. My US ac compressor doesn’t work anymore. My original motor has 311k mi so I decided to do the swap. Done with the swap tonight no check engine or anything. Hope the ac works when I charge it. Thank again!
@crystalcrawford553
2 жыл бұрын
I have a 2000 b16a motor. Would that fit my 2008 civic? It's in my civic hatch younger generation.
@jondoe2099
7 ай бұрын
Leave it in the hatch! 😬😬
@cristiansilva1012
6 жыл бұрын
Can some one help me I have a 08 civic with a R18A1 engine and I bought the R18Z1 how can I make it work the only problem I had was the crank sensor it’s on the wrong side can someone help me
@dennismelville7532
5 жыл бұрын
You already answered your question... extend the crank sensor wires and it should fire right up.
@rodrigomiguel1289
4 жыл бұрын
CRISTIAN SILVA Did you get your r18z1 engine to work in place of the r18a1? i bought a r18z3 to put on mine but the rotation sensor is on the other side and the phonic wheel has more teeth
@rodrigomiguel1289
4 жыл бұрын
CRISTIAN SILVA Did you get your r18z1 engine to work in place of the r18a1? i bought a r18z3 to put on mine but the rotation sensor is on the other side and the phonic wheel has more teeth
@NOMONEY2EAT
4 жыл бұрын
Best place is Osaka Montreal jdm i get my from there all the time .
@BoliMeKurac
5 жыл бұрын
I'm gonna swap out the block on my R18 with the R20. Cheapest 15HP ever
@bhadz100
5 жыл бұрын
Marko Mravak is that a direct bolt on swap without the need to touch the factory tune?
@scsclassics
4 жыл бұрын
Yes , its just the head to a cr-v .
@theejoeylee
5 жыл бұрын
Why the JDM version? Literally no HP difference
@shawnh9677
5 жыл бұрын
cheaper, lower mileage, tested in condition than a salvage yard USDM version mystery
@theejoeylee
6 жыл бұрын
But the JDM one is basically the same HP. I would of just went to a yard.
@johnjoseph7382
5 жыл бұрын
but you dont know if the salvage engine has the engine crack....if you get it from a 2010-2011 it wont be subject to cracking like the 2006-2009's
@beezowdoodoozoppitybopbopb9488
2 жыл бұрын
@@johnjoseph7382 problem is the jk mot sites list them all as 06-11, so no telling which one you get
@johnjoseph7382
2 жыл бұрын
@@beezowdoodoozoppitybopbopb9488 exactly, just go r18a JDM
@beezowdoodoozoppitybopbopb9488
2 жыл бұрын
@@johnjoseph7382 I fat fingered that comment. The jdm importer sites list both 06-09 blocks and 10-11 together as just 06-11. So it's a dice roll whether you get an older or newer casting
@crystalcrawford553
2 жыл бұрын
@@beezowdoodoozoppitybopbopb9488 exactly. I have a cracked block and looking for one myself. I'm confuggled
Пікірлер: 45