This video is great. Don't even look at the printed instructions. This hardware is great. Much better than the stock hardware most standard doors come with.
@ivanlopez4669
Ай бұрын
excellent directions
@aajs669
Жыл бұрын
Just one tip peeps Take off the inside plastic window protector before you hang the door if the space is tight ( small pantry etc ) Awesome vid though , looks fantastic!!! Great product !
@mikegehrke6966
2 жыл бұрын
Great video… very informative and easy to follow! I had taken down doors to put in new washing machine and doors wouldn’t go back up properly! Replaced the hardware with Johnson’s 1700 hardware and works better than new! Thank You for quality product!
@mikeratcliff1446
Жыл бұрын
Great instruction. I referred to not many times
@pdogakron1623
3 жыл бұрын
If it weren't for this video, 5 sets of doors would have been firewood
@19703406
3 жыл бұрын
This was a very helpful video, forget the printed instructions!
@andrewcowan5750
2 жыл бұрын
The printed instructions were something else! And that something was not good!
@personjo100
Жыл бұрын
The part on top that the door is hanging from kept sliding no matter how much i tried ti tighten the screw. Saw a great tip in another video. Just screw in a another screw right the track to act as a stop. I used a drywall screw and it worked great. the door stays in place. Took a few secs for the screw to get through the metal track but it did get through. Just took a few secs with my ryobi drill.
@tonibecerra3769
7 ай бұрын
Thank you 🙏
@briancasey458
2 жыл бұрын
Tip: if the plastic rail slider screws fall out of door make sure after re-screwing the screws that you hand tighten screw bolt just enough to where the piece still locks, then tighten a little more, Then slide door in, lock it and then slide plastic piece into position and then tighten with wrench between top of door and rail. The key is finger tightening the bolt to where you can still lock the plastic piece in the rail.
@bsowieja
2 жыл бұрын
if it weren’t for this video I’d still be swearing.
@adamweinrich4661
2 жыл бұрын
Im sure it must be blatantly obvious to everyone else but Im not clear which is the pivot door and which is the guide door. Why not just say jam door and interior door?
@Catracho57
4 жыл бұрын
I installing those but I don’t know how to do for the jam bracket sprin don’t get down when you mount the doors, it hit the bracket
@mksoni1976
Жыл бұрын
This video saved me from returning your product. It’s a great product but terrible visuals on instructions sheet.
@StevenDMO
3 жыл бұрын
I had tile so my 80" door had to be cut down to 78". No instructions and did not say to predrill holes before you screwed in. Should be common sense but I forgot. : / So, kind of glad I have to cut it down because it aloud me to have a clean piece of wood to drill in to and screw in. Good product, but a pain in the ass to do by yourself.
@juliusrosen1149
4 жыл бұрын
good video but my parts are different - I have rollers ... terrible printed instructions. they need to read the comments.
@rds333
3 жыл бұрын
I agree, the printed instructions are very confusing.
@kevinbrown-ge6sz
4 жыл бұрын
It would be nice if they told you what size drill bit to use to make the holes for the screws.
@James-dp4ye
3 жыл бұрын
Smaller then the screws
@JoeyRam.
3 жыл бұрын
Is not the size (smaller or large), is about the thickness. Take the drill bit in front of the screw and center both making sure you can see the treads (on top and bottom) but not the shank of the screw. That's your right bit.
Пікірлер: 26