Awesome video 👍 clear audio, clear video, thanks bro
@danybalaka3258
11 ай бұрын
Wow! Even thou I cleaned my engine in my Honda your whole car under the hood looks like WOW
@pacific7775
4 жыл бұрын
Thanks brother , helped me out
@zstoysmexicali
4 жыл бұрын
Thank for video👌🏾
@josep5823
3 жыл бұрын
Is the shaft replaceable? Mine was snapped when i took transmission out
@dickbowlmidz
2 жыл бұрын
thanks for the quick reference
@raulmejia2066
3 жыл бұрын
Great ! thank you sir.
@neryhinojosa9785
6 жыл бұрын
It’s better if you put the throw out bearing on the arm before you put it back
@ahmadabboud1535
5 жыл бұрын
I wish i had done this, now its fucking vibrating and i need to remove my gearbox to put it back on properly, im so annoyed.
@balloney2175
3 жыл бұрын
Is this the same as Honda Civic DX 1997?
@gillotine1beatsrhymeslife717
4 жыл бұрын
Awsome thanks
@trackaholic
7 жыл бұрын
Thank you for this video! I have a question. My fork is really loose (I have the transmission on the ground) and when I move it and doesn't spring back into place. Is this normal? I can't tell if you're moving it forward and back on your own or not. Thank you
@NAUS2K
7 жыл бұрын
Sayyid nope that's normal, when the trans is out of the car the fork can move around freely , the slave cylinder is what pushes the fork
@trackaholic
7 жыл бұрын
Thank you for the reply! It really helped. I put my car back together and everything is going smoothly. I'm just getting a noise (sounds like the throwout bearing) when I press the clutch pedal ALL THE WAY in.
@dariomendoza6892
6 жыл бұрын
pretty cool !!!
@Rhosticks
8 жыл бұрын
Good stuff
@mattteacher2362
3 жыл бұрын
clean engine
@josegenterola1995
Жыл бұрын
Has the bell housing been cleaned. Look dirty.
@Error1M.
Жыл бұрын
Hey thanks for the video very informative if u don’t mind quick question My accord 2009 5 speed i changed the engine a year ago and everything was fine but now when i tried to bleed my clutch the slave cylinder doesn’t kick back what can it be or how can i properly bleed the clutch or is my fork or anything wrong?
@InTheZone85
4 ай бұрын
anyone reading this later and still wondering, make sure you have someone press in all the way and hold the clutch pedal while you open the bleed valve, then tighten gently (doesn't need to be cranked down). Then pull up the clutch pedal. Repeat this process until fresh, gold brake fluid comes out in a steady stream. Pull up on the clutch pedal one last time. After it's fully bleed, push down on the pedal, it should then return up on its own Also make sure there's some slack (a tiny amount) in the clutch pedal. You want a very small amount of play before you feel the clutch pedal pressurize/start to disengage. If the pedal has no play then you'll kill your throwout bearing and potentially wear your clutch disk faster than you should. You don't want so much play that you can't fully disengage the clutch, preventing you from smoothly shifting gears.
@damiropadobarglumskiperiod505
Ай бұрын
Does peugeot have that retaining clip spring
@AnythingGoesJoJo
4 жыл бұрын
He didnt correct himself installing the fork first before the bearing...note the slight edit on the video
@samcook6841
2 ай бұрын
I was one who bench the trans off and on lol found it much easier tbh
@alexandervelasquez5912
3 жыл бұрын
Necesito el video de donde pone la horquilla en el balero
@camachosotelo289
4 жыл бұрын
Is the throwout bearing suposse to be in contact all the time with the finger plate?
@brayanmartinez2923
3 жыл бұрын
No
@sahanbro1182
Ай бұрын
❤
@537R4HC
6 жыл бұрын
question about ur throw out bearing cause see the middle thing color red its plastic right? its supposed to be plastic? its safe?
@NAUS2K
6 жыл бұрын
Yeah it just slides along the aluminum cylinder, no forces go through the plastic surface
@537R4HC
6 жыл бұрын
how about the heat? not gonna melt ?
@mushy18100
6 жыл бұрын
Chalres Andrew: good question! Yes, That plastic from Honda Japan can withstand heat for thousands of miles. That’s why everytime you change or replace clutch kit, you also need to replace the throw out bearing as well as the release fork boot. Hope it helps.
@SlinkyTHAshooter
3 жыл бұрын
I see you are from CNY. Do you have a Facebook page to dm you?? I got a few questions.. eg coupe k24a2 swap and it’s my first build.
@juliosdiy3206
11 ай бұрын
What is wrong with the bearing?
@NickDiNunzio
8 жыл бұрын
God, that s2000 is gorgeous.
@FiveMadNess
7 жыл бұрын
so mine bearing is not on right it pushes close to the transmission teeth at the tip. like it sometimes goes over it. is this okay?
@saran4999
Жыл бұрын
Did you figure it out? I have the same problem on my k24 gearbox
@mart673g
3 жыл бұрын
What supercharger is that? Do you have a link?
@memechanichalelectiric6769
Жыл бұрын
👍👍
@evolutionblitzz3256
8 жыл бұрын
Don't know if you will see this, but if you still live in New York, there is an auto cross at the end of 7-87
@evolutionblitzz3256
8 жыл бұрын
Tomorrow
@NAUS2K
8 жыл бұрын
+Evolution Blitzz Yeah that's the mohud scca event right? I use to live near Albany and did the mohud scca races , I'm in CNY now and do the scca league out here now
@evolutionblitzz3256
8 жыл бұрын
+NAUS yeah I remember the car from fortitech, that's cool though
@tavojuarez1987
6 жыл бұрын
Can I take the fork out without dissarming the trans? I feel my clutch a little bit stiff and would like to put some grease on the pivot points. thanks.
@NAUS2K
6 жыл бұрын
you probably could if you can get a tool in the small opening to undo the retaining clip, then it should just slide out, however its much easier with the trans off the car
@tavojuarez1987
6 жыл бұрын
NAUS thank you!
@balloney2175
3 жыл бұрын
@@NAUS2K I have the same problem. The retaining clip is not properly attached. Can we really slide out the fork?
@iamteedoh
3 жыл бұрын
@@balloney2175 I know this is an old question but the answer is no. You can technically get it off but it'll be damn near impossible to get the fork back to align with the throw-out bearing in order to have the fork attach to the throw-out bearing. You also then have to ensure you can snap in the center ball joint from the bell housing of the transmission into the fork through its retaining clip.
@death2sora
Жыл бұрын
5:17 🤣🤣🤣
@LuckyHorse-zj1rt
2 ай бұрын
You should clean your transmission before putting it back in bad for clutches and flywheel even for the bearings
@LuckyHorse-zj1rt
2 ай бұрын
You didn’t even know how to install it you put on wrong first lmao😂😂😂
@raisethecolours
2 жыл бұрын
Urea is concentrated pee from china btw... same stuff is in DEF diesel fluid.
@NAUS2K
2 жыл бұрын
Well the concentrated pee has been working great for years!
Пікірлер: 55