I subscribed to you a while back when I bought my first gt80, and you were a great help... now I recently purchased a ke100. Can’t thank you enough for your help kevin!
@2strokeguru
3 жыл бұрын
That's awesome very welcome send pictures of your project handymotorman76@gmail.com thank you for your support
@baqcasanke
6 жыл бұрын
Hey buddy! Your videos have really been helping me out a whole ton, i just picked up a 1980 ke100 and ive been watching all your videos. You gained a subscriber today
@2strokeguru
6 жыл бұрын
Baqca Sanke awesome thank you
@clayshorting5605
3 жыл бұрын
Hello! Thank you for all your videos and sharing all your knowledge. I just bought a 1980 kd100.. your videos are a great help and very helpful
@2strokeguru
3 жыл бұрын
Thank you for your support kd100 is a great bike remember ke km kd mc1 all share same engine family
@clayshorting5605
3 жыл бұрын
@@2strokeguru I watched your video about ignition , I was able to switch my ignition coil and get my 80 kd100 running for a bit. Now it won't start unless I push start it and it has to have the throttle wide open to run. Then it stalls. Am I able to clean my carb without having to replace the gasket and other stuff? I'm having a hard time finding parts and help in my town. I'm up in Canada , I really like watching your videos. The carb is spitting gas out when the cover is off and its leaking from the bottom.
@2strokeguru
3 жыл бұрын
@@clayshorting5605 do you speak English
@2strokeguru
3 жыл бұрын
If you do i will give you my phone number
@fritzlannowack2701
2 жыл бұрын
KEVIN THANKS SOOOOOO MUCH. I got the time to test my 79 ke 100 after putting the new cluch in and it works great thanks so much it is a fun old clasic
@2strokeguru
2 жыл бұрын
That's awesome great job very welcome
@fritzlannowack2701
2 жыл бұрын
@@2strokeguru okay Kevin so on the left side where the chain tensioner pushes against is bent and have been bent before ( I just bent them back in the past) and since they did that they are really weak at the bend. It is to the about to snap point and I was wondering if it would be okay to weld them for reinforcement?
@masterrestorer1882
5 жыл бұрын
I hate long videos....yours was enjoyable and full of much needed info. Can't tell you thanks enough for walking us all through this. You should set up a go fund me at a buck per advice. I'm certain you have saved many so much time and money and taught us how to keep our toys up and running. Hats off to you from
@2strokeguru
5 жыл бұрын
Awesome thank you for the great compliment if you haven't please subscribe and thank you again this channel is built to help at all levels of mechanical skills
@pyzik200
7 жыл бұрын
Holy hell, knowing about that plug would have made my life SOOOO much easier.
@kiranmodagi
6 жыл бұрын
Very helpful video ! I have the same bike in India named as KB100 and no information is available about this bike. Thankyou for taking your time and explaining :)
@2strokeguru
6 жыл бұрын
kiran modagi welcome
@taffydownunder6457
3 жыл бұрын
Love your videos great help thank you for making them
@2strokeguru
3 жыл бұрын
very welcome
@TheVSChick
2 жыл бұрын
This is a great vid. Thanks for the clear explanation. 🤘
@datuptownb0y
3 жыл бұрын
Good shit just bought a ke100 never seen a carb setup like this lol 🤙🏾
@jasonmoore7751
6 жыл бұрын
Yeah. I was just watching your video again and seen that. I tried to get it out but it did like you said they do sometimes. I'll try some penetrating oil in it. I let some carb cleaner soak in the hole yesterday but really wanted to take it out. Thanks.
@dconcb
6 жыл бұрын
Kevin Bergeron, Thanks for sharing your knowledge! I just picke up a 73 g5, and was curious about pressing out the needle jet/ emulsion tube. I’ve done it many times on Honda’s but wanted to make sure it was safe to do. Any advice? Also, the filter/drain in the right side cover, is this threaded in or pressed? Manual doesn’t say. Hope you can help, thanks
@saqibnawaz5139
4 жыл бұрын
Vry informative bout ke carburetor, especially modifying screwdriver to much needed measurements
@seancainey3979
Жыл бұрын
Great video!
@joshmx7161
4 жыл бұрын
Hey Kevin, what is the stock pilot (air/fuel) screw adjustment on the KE100? I can’t find it anywhere. Need to richen my bike up a tad for the winter temps
@correia9
4 жыл бұрын
Hi Kevin, Thanks for your videos, I've tried to adjust the idle of my bike (Kawasaki G7t), but know I can´t start it, I've put the screw 1 and a half turns but the bike don't start, the idle speed screw should be at what position? What is your advice to adjust it? Thanks
@CospersCatch
5 жыл бұрын
Great job man thanks this helps alot
@2strokeguru
5 жыл бұрын
Welcome thank you
@julietramsay861
Жыл бұрын
Hey Kevin just replaced the condenser on my bike and just to check. Will the bike run with the air box off?
@michaelsullivan5005
3 жыл бұрын
I got a kh100 sticker says 1975 but i seem to only find 76. But all ke100 and the AC100 carbs will work also with this bike will the covers also work. Or any boots that go to it. And ebay carbs are good ones to buy? Mine came with no carb or cover:(
@andrewhansen5485
4 жыл бұрын
Hey Kevin one more question, so I have done almost everything and NOTHING is working. I was hoping you would help. So the symptoms are it is SUPER smoky, it won’t idle at all, it will only idle on choke, it has no power in first two gears but the other gears PULL, and it seems like it is sucking air...just replaced both crank seals and still same results. Could I have installed them improperly?? Thanks! Edit: no oil under the stator cover! That means left crank seal is good! So right crank seal again or what?
@nathanestes1342
6 жыл бұрын
Dude you sound like Peter Griffin.
@2strokeguru
6 жыл бұрын
maby i am lol trust me im married i have been called a lot worse
@WICKEDPONY81
6 жыл бұрын
EntryCentral AKA Nathan Estes indeed
@2strokeguru
6 жыл бұрын
huh
@wmaillard
7 жыл бұрын
Thanks man, this is awesome!
@2strokeguru
7 жыл бұрын
welcome
@ifvansant
5 жыл бұрын
Super helpful! Just cleaned the carb on my '76 KH100. The plastic idle speed adjustment knob that sticks out the top boot on mine slips on the knurled metal knob underneath -- so I can't adjust the idle speed while riding. Maybe I'm missing a part, but it looks like the plastic knob is just supposed to grip the metal? Got any tips to keep this from slipping?
@2strokeguru
5 жыл бұрын
Red loc tight
@josuemendoza6445
Жыл бұрын
Hey Kevin, what would you recommend for a broken throttle cable? Since I can’t seem to find any oem replacements anywhere nearby and they don’t make any aftermarket cables specifically for the ke100. I saw some universal ones that come with the entire throttle tube assembly, but I would prefer not changing out that much. What are your thoughts on this? Thanks in advance!
@2strokeguru
Жыл бұрын
Have you checked ebay or go on Google they have custom cables you can buy a custom cable also the kh90 kh100 kv100 trail boss 100 all use same cables hopefully this will help with your search
@80SWoods
5 жыл бұрын
Where can I find a new rubber seal that goes between the carb and the intake tube? I’ve looked for days on different online retailers and can’t find it in the diagram showing this seal. I found it for the old model carb (with the idle screw on the outer front of the carb, but mine is the newer (1990) model) and I can’t seem to find this seal for the newer style carb. In your video, you said the carb spacer between the carb and intake tube was a different diameter for the old and new model, so I assume the seal is also different.
@anotherdrummer2
3 жыл бұрын
I have the same question. Did you ever find a replacement?
@2strokeguru
7 жыл бұрын
thank you for your support
@nmillertym
3 жыл бұрын
Willa newer carburetor work on a 1981 ke 100. I bought one and it fits perfect except the float overflow is on the wrong side and there is two extra ports that is in the new one
@2strokeguru
3 жыл бұрын
Yes they are vents
@mattwirtz2751
3 жыл бұрын
Kevin, great video. Couple quick questions regarding my 1970 G4TR Trail Boss. 1.) When looking up and ordering parts, whats the difference between a G4TR-A, G4TR-B, and G4TR-C and how do I identify which version/model I have? 2.) I'm looking for a replacement air cleaner element (schematic aligns with G4TR/A/B part) part number 11013027, but only see one used one on ebay that's missing the foam ring and it's $100.00. Are there other air filters from different kawasaki bike models that would fit and work, or other aftermarket reproductions that can be sourced somewhere?
@2strokeguru
3 жыл бұрын
Check the UNI airfilter website and there's a sister bike to your bike kv100
@chrisharm6242
Жыл бұрын
I’m getting a hissing sound coming from the carb when I slowly kick down?? Any ideas?
@parkeremeigh4229
7 жыл бұрын
Would not having the grommets have anything to do with no idle?? I've sealed that air box, messed with the idle screw, checked the filter, and everything. BUT I am missing the grommets for the front and the fuel line. Does that pull in to much air and throw off the mix? Thanks so muvh
@2strokeguru
7 жыл бұрын
it would if you got water in it not have the grommets allows dirt in and engines dont like dirt you could get dirt in the idle circut in the carb
@aggieforlife13
4 жыл бұрын
Kevin great video. One thing hard to tell is which bike model is which. I have a 96 KE 100. I noticed you mention the carb says the model number but looking at the screenshot there are multiple carbs with the same number but have different jet settings.
@joshpaulson452
5 жыл бұрын
Hey Kevin, working on my 2000 ke100 and have a few questions. I am running my bike and am getting backfire and or bog on the acceleration of the bike. How man turns out does stock reccomend, I am at altitude so I may have to adjust accordingly. Are the needle jets interchangeable on the different carbs?
@2strokeguru
5 жыл бұрын
Backfire on a 2000 ke100 change the spark plug first
@jasonmoore7751
6 жыл бұрын
Thanks Kevin! I was kinda hesitant about checking the pilot jet because of the plug but was thinking I would have to. I bought a new plug. I think it's a ngk r. 11/2 turns out on pilot jet right?
@2strokeguru
6 жыл бұрын
the idle mix screw is 1 1/2 turns the pilot jet is next to the main jet in the carb in the tube
@nathanjohnson5988
3 жыл бұрын
Excellent video! Searching for the filter that you mention at 6:00 (below the carb). I don't have one and don't see it on the parts diagram. What search terms do I need to use in order to find one?
@nathanjohnson5988
3 жыл бұрын
Found it after looking for a while. It's PLUG,25X12 16116-006.
@dorsetboy3834
3 жыл бұрын
Great video I have a g4100 do u no how too adjust the fuel flow into the carb
@2strokeguru
3 жыл бұрын
I have videos on that
@sanjayvhawal2404
2 жыл бұрын
Dear Kevin, Your VDO are very useful and give lots of knowledge, Pls use camera tripod so that it will be hands free shooting. tks sanjay PUNE INDIA
@TheBeardedSandman
4 жыл бұрын
I'm working on a 73 that's been sitting since about 2002. After rebuilding and cleaning the carb a few times, it only runs at basically full throttle - I suspect one of the Jets is clogged but I'm not sure how to clean it... Any ideas?
@urbanitesgarage3299
4 жыл бұрын
Same exact issue I'm having
@aamirsajjadqureshi8844
3 жыл бұрын
very informative video thank u sir
@2strokeguru
3 жыл бұрын
Thank you
@BikerStuff
2 жыл бұрын
Great vid, thanks. But there are no Phillips screws on a Japanese bike. The one holding the carb clamp on is JIS
@2strokeguru
2 жыл бұрын
I have been doing this for 30years Philips #3 fits correctly
@BikerStuff
2 жыл бұрын
@@2strokeguru JIS is nearer to Pozi than Phillips. Buy a set and you'll stop chewing the heads.
@jasonmoore7751
6 жыл бұрын
Hey Kevin! Awesome videos! Just recently got a 2000 ke 100 in good shape for 200 bucks. Front rim was bent and petcock was broke. Got both from ebay. cleaned the carb and checked a couple other things you said to check on your videos but still cant get it to run right. It starts but races and dont want to idle. I had all of the jets out except the one that is down in in front of the main jet. I think you said it was the idle jet. Float is level like you said and everything else seems to look good. Bike was very clean even inside the airbox where carb is so I figured I would be able to get it going no problem. It is also smoking pretty heavy so I just watched your video about the oil adjustment and am going to try that tomorrow. Do you think that could be the problem?
@2strokeguru
6 жыл бұрын
thats a great deal congrats check your pilot jet and spark plug if the plug is a resister plug that could be the problem
@eligaudio12
5 жыл бұрын
cleaned the carb on my 1975 kh100 and it stopped leaking but still only runs for 5-10 seconds with the choke on. any recommendations on how to adjust the carb?
@2strokeguru
5 жыл бұрын
If it only runs on choke that means it is not getting fuel it needs clean the fuel tank petcock the bowl on the petcock
@robertmiller2720
6 жыл бұрын
Rebuilding the KE100 I had as a kid with my teenage son. Love your vids. I was looking for the air box filter located on the case below the carb. Can you link to the ones you said you found on eBay? Thanks!
@2strokeguru
6 жыл бұрын
Robert Miller I will check tonight when I get home thank you for watching and subscribing ke km kd mc1 all the same for that part
@user-dr8pn3lk8n
4 ай бұрын
Hey Kevin how you doing I have the original carburetor for my 100 KD but I'm missing the float Bowl what size of a float Bowl would work on that and what type would I need to get that old carb working again working again thanks
@2strokeguru
4 ай бұрын
Ke100 kd80 km100 km90 G3SS mc1 90 all fit
@2strokeguru
4 ай бұрын
I'm doing well thank you
@MainelyMoto207
4 жыл бұрын
What's the difference between a KE100 and a KM100A?
@nathanjeffers5670
6 жыл бұрын
So I recently purchased a kv100 1976 it has been backfiring through carb I put a new plug in.. Problem the same... Any help would be appreciated
@2strokeguru
6 жыл бұрын
nathan Jeffers clean or replace the points
@HaveUSeenMyBaseball86
2 жыл бұрын
What are the links for these filters
@coleknippen730
6 жыл бұрын
Dude u rock!
@2strokeguru
6 жыл бұрын
Cole Knippen thanks
@ryancollick6670
5 жыл бұрын
Awesome information that I've been looking for. I just picked up a 1980 Ke 125 and having trouble finding a new carb. Any suggestions on a similar one?
@2strokeguru
5 жыл бұрын
Do you have the original carburetor
@ryancollick6670
5 жыл бұрын
@@2strokeguru I only have the housing. Most of the internals are gone and the cheapest float i found was around $65
@2strokeguru
5 жыл бұрын
@@ryancollick6670 text me pics of carb 6033958097
@kawasakipeshawar
4 жыл бұрын
Is that japni carborater
@Frankucchy
6 жыл бұрын
I have a kawasaki kh 100 use the same carburetor!! Where can I download the manual that you use? Thanks
@2strokeguru
6 жыл бұрын
Frankoo I have the actual manual its a clymer Kawasaki rotary valve 1966 to 2001
@gayathrigayathri4861
2 жыл бұрын
Hello sir..., why in kh100 model bike , this carburetor throttle slide have small hole... I don't know the solution...
@dougiedew4775
5 жыл бұрын
Kevin, do you see much issue with using a 78 jet vice a 75 jet in the carb on a 75 G4?
@2strokeguru
5 жыл бұрын
No both are lean jets I like the 80 in that bike
@dougiedew4775
5 жыл бұрын
Kevin Bergeron thanks for the advice.
@beni.5290
5 жыл бұрын
I got ke100 90's.My carb is clean but why there is always a leaked. What Im going to do to stop leaking?. Pls help me. Is there any deficiency bcoz the bike is already old?
@feliciacummings7948
5 жыл бұрын
Do you have a cover over the carbarator or can i leave it off
@2strokeguru
5 жыл бұрын
Leaving the cover off is bad for the engine dirt can get in the engine and destroy it dirt can damage the clutch adjuster assembly I have covers
@eelnoizpanx
2 жыл бұрын
Hey man I'm sorry I don't get to call ya. My friend left already for new Hampshire so I'll bother you next time I'm into the G5. Thanks. But I have a question about a TS 185 if you have time.
@2strokeguru
2 жыл бұрын
No problem call me tomorrow after 4pm
@nathanupton5151
6 жыл бұрын
Where can I get a new carb mine is missing the entire top end on my km100
@2strokeguru
6 жыл бұрын
Nathan Upton the slide part
@laureanosanchez5265
4 жыл бұрын
Hi Kevin, i'm working on my KE 100 94 and i would like to know how yo pop out the thing of the min 10:38 greetings from Argentina. And thank you for teach us all how to repair these bikes :D.
@2strokeguru
4 жыл бұрын
I am at work I will check tonight
@laureanosanchez5265
4 жыл бұрын
@@2strokeguru oh Kevin you already made a video sorry and thank you again ;)
@alanb9509
4 жыл бұрын
Hola Campeón, soy de Argentina. Necesito conseguir el kit del carburador ese pero el 26mm que va con la gto 125 y el kh 125, sabes donde conseguir el kit de reparación?
@frankiemarchese2978
6 жыл бұрын
Is there any way to adjust the idle speed on these bikes? My stock pilot jet wont let the bike idle, but i have a bigger pilot jet that makes it idle but its too high.
@2strokeguru
6 жыл бұрын
Frankie Marchese to adjust your idle speed is adjusted next to where the cable goes into the carb on the very top the screw you where adjusting is the mix screw not idle speed
@frankiemarchese2978
6 жыл бұрын
Thank you, running great right now. Starts up 1st kick. How much transmission oil do the ke100s take? I have a 2000. Also should I use 10w 40? Thank you again! I checked the check bolt, theres oil in it but looks dirty.
@2strokeguru
6 жыл бұрын
till it comess out the oil level plug located net to yhe kickstarter at where the kickstarter comes out od the engine and it 10w30 or 10w40 eather worksgreat
@2strokeguru
6 жыл бұрын
you are welcome
@johndasilva66
4 жыл бұрын
Does the choke plunger come off? I'm trying to rebuild but just seems to be stuck and can't move.
@2strokeguru
4 жыл бұрын
No it's 1piece
@johndasilva66
4 жыл бұрын
@@2strokeguru oh ok, it's really stuck and it only moves down and not up
@2strokeguru
4 жыл бұрын
@@johndasilva66 carb slide
@johndasilva66
4 жыл бұрын
@@2strokeguru Thanks Kevin!
@stevendaniels8652
2 жыл бұрын
Your viewership is growing. I tild you you would have a tv show eventually. Any sponsors yet?
@2strokeguru
2 жыл бұрын
lol yes you did
@devinnice2409
3 жыл бұрын
Can you do a video on adjusting the carb?
@2strokeguru
3 жыл бұрын
Yes i can
@waqasjamil9
3 жыл бұрын
Very Nice.. 👍 Can you upload a copy of manual you are using for reference and share through some link such as Google drive.?
@2strokeguru
3 жыл бұрын
I have books i cant upload but I do recommend buying the manual
@rangdy4936
2 жыл бұрын
I have ke100 1995, whats the exact valve clearance measure? Thanks
@2strokeguru
2 жыл бұрын
Valve clearance?
@rangdy4936
2 жыл бұрын
@@2strokeguru sorry im new to motorcycle. I want to take it to mechanic and i want to be tuned up
@jaystrucksandtoys8770
5 жыл бұрын
What kind of gasket is needed? What do they call it?
@2strokeguru
5 жыл бұрын
The gasket for the cover
@parkeremeigh4229
7 жыл бұрын
Is there any way I can get in touch with you? I have several questions about my ke100 and it is my first project. Your Channel has been very helpful so far though!
@2strokeguru
7 жыл бұрын
awesome email me and i will give you my number luggnutz76@yahoo.com
@WICKEDPONY81
6 жыл бұрын
Parker Emeigh lol me too have a 91 ke 100 striped idle screw....thos bike was 1 owner..I.e me being the 2nd..has 750 miles...wont idle...
@WICKEDPONY81
6 жыл бұрын
I wss told that its a cheap fix...like 2.99 for the screw..but they couldn't get it out...honestly dont know what they are talking about...
@MainelyMoto207
4 жыл бұрын
I have the older rectangle carb, should I just skip trying to rebuild it and get the newer style?
@2strokeguru
4 жыл бұрын
the older rectangle carb is made by Teikie its a great carb i just put one on my Kawasaki KDE90 bike build however very hard to find parts for if you cant find parts the Newer style carb is the way to go
@MainelyMoto207
4 жыл бұрын
@@2strokeguru so the new carb should slide right in without a problem?
@2strokeguru
4 жыл бұрын
@@MainelyMoto207 the slide is not interchangeable but yes replace complete carb setup 100% fit
@MainelyMoto207
4 жыл бұрын
@@2strokeguru excellent, thank you!
@2strokeguru
4 жыл бұрын
@@MainelyMoto207 welcome
@seththegamer200
11 ай бұрын
hey, do you know where i can get parts for a bike like this?
@2strokeguru
11 ай бұрын
Ebay and partzilla.com
@2strokeguru
11 ай бұрын
Ebay and partzilla.com
@seththegamer200
11 ай бұрын
@@2strokeguru thanks but partzilla just ain't it for Australia
@2strokeguru
11 ай бұрын
@@seththegamer200 Australia I have no idea
@parkcircle29405
5 жыл бұрын
What's the best source for a carb rebuild kit for a 2000 ke100
@2strokeguru
5 жыл бұрын
Ebay 1980s up
@parkcircle29405
5 жыл бұрын
@@2strokeguru thanks
@brycelawrence7905
3 жыл бұрын
I just bought a carb but it has three ports on the side and one on the bottom I'm confused on what goes where
@brycelawrence7905
3 жыл бұрын
One of the ports is black plastic
@2strokeguru
3 жыл бұрын
They are vents
@brycelawrence7905
3 жыл бұрын
@@2strokeguru are you sure my old carb has the two on the bottom but this new one only has one on the bottom
@2strokeguru
3 жыл бұрын
@@brycelawrence7905 yes after market carb only has 1
@JAMTOAM
3 жыл бұрын
I have ke125 78 and having idlein problems and also get it to go bogs out a lose power
@2strokeguru
3 жыл бұрын
Check fuel flow from the tank and float adjustment
@JAMTOAM
3 жыл бұрын
@@2strokeguru fuel flows to motor just feel like like it comes and goes I was thinking of take apart carb clean her up and the jets inside and then try to run agian
@JAMTOAM
3 жыл бұрын
Witch mikuni carb is on a ke125 78 I think of get a new carb and slap it on and see there what happens
@JAMTOAM
3 жыл бұрын
I need help for real
@JAMTOAM
3 жыл бұрын
Also what is the measurement for the float I cany find real good info on these bikes over here in canada
@king_deniervvv5975
6 жыл бұрын
Hey kevin i need some help i got a 1990 ke 100 it was setting up for a few months before i got it well i put some gas in it and it fired up and ran great. After going down the road a time or two in first gear i decided to push the bike a little harder shifted to secound and it started stuttering and then died.... so i walked it home pulled carb and cleaned it but now it wont start at all still have great compression spark and all any ideas what is going on
@2strokeguru
6 жыл бұрын
king_ DENIER try changing the spark plug
@king_deniervvv5975
6 жыл бұрын
I will try it tomorrow and lwt you know
@2strokeguru
6 жыл бұрын
king_ DENIER kool
@king_deniervvv5975
6 жыл бұрын
I checkedd spark plug no fire so i got a new spark plug and still have no fire im not sure y it was sparking before but now its not
@2strokeguru
6 жыл бұрын
king_ DENIER you need to clean or replace the points you can use a nail file to clean the points
@greglawson8001
4 жыл бұрын
Is the Suzuki ac100 carburetor going to work for a 1986 kd80
@2strokeguru
4 жыл бұрын
Yes it will ke km kv kc kh kd mc1
@greglawson8001
4 жыл бұрын
@@2strokeguru okk I be been working on this bike I see no reason it won't work last time I took the carburetor off I mess with the floats it was leaking real bad so I took it back off and got it to where it seems like gas isn't leaking out but there still gas in the bowl the problem is it won't fire on gas but can fire off of starting fluid
@greglawson8001
4 жыл бұрын
I was worried about the round part where it goes into the intake I didn't know what size I watched a few different videos to find out what carburetor it's supposed to match thank you very much
@greglawson8001
4 жыл бұрын
I would like to be able to ask you a few questions first :)
@greglawson8001
4 жыл бұрын
When I looked up the carburetor it looks like it has two places where a gas line goes in
@CrimsonYetiCartoons
3 жыл бұрын
Kev if you ever come down to Florida, I got a 72 G5 you can have. I've been working on this thing for months and cannot get it to start. Everything is good, compression, spark, timing, rebuilt it all... It will not pull fuel and start. I've cleaned the carb a dozen times and fiddled with every setting. I'm losing my mind. Come down and take it from me. I'm sick of this thing. It's cursed and I don't want it.
@2strokeguru
3 жыл бұрын
603 395 8097
@wolfymaceastern6072
2 жыл бұрын
Just if anyone struggles for parts the bajaj kb100 built in India is a Kawasaki kh100 with the tank and panels off the kh125 so parts including carbs etc can be ordered new from India
@king_deniervvv5975
6 жыл бұрын
I changed the points and everything still no spark so only thing i can guess is i need a new stator do u know wheres the best place to get a stator affordable
@2strokeguru
6 жыл бұрын
king_ DENIER what did you gap them at and did you change the condenser
@king_deniervvv5975
6 жыл бұрын
I had a professional in my area change the points and he gapped them i will call him and see if he gaped the points
@king_deniervvv5975
6 жыл бұрын
And it doesnt look like he changed the condenser where would i buy one and how much are they
@king_deniervvv5975
6 жыл бұрын
This bike went from my favorite to a nightmear in 5 min
@2strokeguru
6 жыл бұрын
king_ DENIER new points have to ask and find out what they where set to theas bikes are different from most
@jacquellward6440
5 жыл бұрын
Where can I get a carburetor gasket or full carburetor for a 1985 kx100
@2strokeguru
5 жыл бұрын
A kx100 or ke100
@jacquellward6440
5 жыл бұрын
Kevin Bergeron I meant a ke100 like my bike keeps leaking gas from the bottom
@2strokeguru
5 жыл бұрын
@@jacquellward6440 oh check out my carb talk videos its not the gasket it eather needle and seat or float adjustment
@jacquellward6440
5 жыл бұрын
Kevin Bergeron so it’s not a gasket problem?
@2strokeguru
5 жыл бұрын
@@jacquellward6440 leaks past the needle and seat fuel level increases and flows out the over flow at the bottom of carb
@brianabbott5315
6 жыл бұрын
Hey Kevin I have a 08 1980 Kawasaki km100 and I don't quite know how to tune my carburetor because it's not getting up to speed it's supposed to be
@2strokeguru
6 жыл бұрын
Brian Abbott I have a bunch of carb videos the km and ke are the same setting 1 1/2 turns out from seat and float 24mm from gasket to top of float and make sure main and pilot jet you can see light through and the get in your carb bowl it located in the circle tube in the bowl
@brianabbott5315
6 жыл бұрын
Thank you Kevin Bergeron I appreciate it very much but to be honest with you I don't understand what you mean because I do have a disability and it's hard for me to make sense of texts it's better it we talked, would you possibly be able to email me and I could give you my cell phone number and hopefully you can elaborate a little bit more on this topic over the phone you can email me at hobbitabbott@gmail.com
@2strokeguru
6 жыл бұрын
Brian Abbott check out my other carb videos email me luggnutz76@yahoo.com with your phone I will call you or send me a Facebook message and I can do pictures through messenger
@TylerTheBassCreator
4 жыл бұрын
@@2strokeguru can i email you please? Have a couple quick questions
@2strokeguru
4 жыл бұрын
@@TylerTheBassCreator are you in the us
@looking_33
2 жыл бұрын
I dont have an idle air screw
@2strokeguru
2 жыл бұрын
What kind of bike do you have
@looking_33
2 жыл бұрын
@@2strokeguru hi i have a 2001 ke100. I think i have it figured out from watching your other videos. I drilled out the little plug and found it behind there…
@jasonmoore7751
6 жыл бұрын
No idle seems to be a problem with these bikes.
@baqcasanke
6 жыл бұрын
Can you please help me? My KE100 runs too rich, like way too rich. It starts up great, and runs good for 15~ minutes but when the engine gets hot it backfires, sputters and stalls. The piston and cylinder are full of carbon buildup, as is the expansion chamber. I can't figure out how to lean out the carb so that it runs longer than 15 minutes... Please help! I love your channel man you're the bomb! Thanks in advance
@baqcasanke
6 жыл бұрын
Btw i changed the fuel filter, cleaned the tank and petcock, new spark plug, new head gasket, cleaned the expansion pipe with a steel cable and drill, new 2 stroke oil, new transmission oil, new battery, and i tried to fix the carb but still too rich...
@2strokeguru
6 жыл бұрын
running too rich means its getting more fuel than air it causes the engine to run cooler resulting in carbon build up one of the most common problems is a dirty air filter or a air flow restricton like a mouse nest in the air box DONT run the engine with out a air filter cause that will cause extreme opposite problem lean condition start there and let me know how you make out
@baqcasanke
6 жыл бұрын
Kevin Bergeron i've already checked the air filter, almost brand new, im fact it was the best looking part on the bike when i bought it.
@2strokeguru
6 жыл бұрын
Baqca Sanke have you cleaned the carb
@baqcasanke
6 жыл бұрын
Kevin Bergeron yes, many times. The needle is not adjustable: it has only one setting for the clip position.
@hugieflhr03
5 жыл бұрын
Great advice on the Suzuki ac100 carb, it’s much cheaper than the KE100 carb!
@2strokeguru
5 жыл бұрын
It is a good carb I have it on 4 bikes run great right out of the box
@TheEnduroClub
5 жыл бұрын
Nice Video! I had mine restored and modified to a mono-shock. Great bike. I had it for over 20 Years! I just made a video, you may check my videos if you like =)
@frankdillon6127
2 жыл бұрын
welch plug is for american EPA regulation. not to be tampered with.
@2strokeguru
2 жыл бұрын
You have to to adjust the carb Rember bike is worn not new factory adjustment is not the same
@frankdillon6127
2 жыл бұрын
yeah i agree, but as to why it is there as i understand on car carbs was the infernal government trying to stop people from messing with the adjustments. i could be wrong wouldn't be the first time. @@2strokeguru
@2strokeguru
7 жыл бұрын
luggnutz76@yahoo.con email me your number i will call you
Пікірлер: 241