You are the man. Needed a trigger wire for Baja design S1s for relay on my ‘17 SDGT. Such a simple thing that KTM did NOT put in the manual.
@pmdrummer
6 жыл бұрын
Just installed mine, same bike, same GPS but I routed all the cables down behind the gauges. Took the gauges off, 3 screws, and disconnected the cluster. After that I pushed all the wires through the gasket behind the cluster and plugged in. Super clean install and looks great.
@dimosk7389
3 жыл бұрын
once again, your video is straight to the point. i am going to buy a quadlock wireless charger, and wanted to permanently hook it to the bike, instead of using the 12V socket and you gave me the answer as simple as possible. thanks man
@2WR
3 жыл бұрын
Glad the video helped!
@therealcalspeed
7 жыл бұрын
Dude, you rock with your simple vids.
@2WR
7 жыл бұрын
Appreciate the feedback!
@RidinCountry
7 жыл бұрын
Electrical is one aspect of motorcycles I have zero knowledge on.. well I did know brn was ground!! 😬.... great job on the vid Mario!! ✌️
@2WR
7 жыл бұрын
+Ridin' Country most of the time Black is ground but it varies. I learned electrical wiring installing car stereos when I was in HS. Thx bud!
@greglewis9259
6 жыл бұрын
Great how to videos,short and sweet. Found the acc 1/2 wires in the tail thanks to this vid, but can you tell me what the unused 14 place connector in the big boot is for? Thanks, Greg
@2WR
6 жыл бұрын
Greg, I haven't had time to check on my bike but according to the service manual 14 is for radiator fan 1.
@waynekerr8003
2 жыл бұрын
Where about in the tail did u find the acc 1 and 2 wires, under the seat near the battery?
@gustwowheeling7337
7 жыл бұрын
Good stuff, Mario! Thanks for sharing, and be safe.
@2WR
7 жыл бұрын
thanks Gus
@ncaridade
3 жыл бұрын
Hello, thanks for the explanation. Could you please explain how to install auxiliary lights? Should we use Acc2 as well? Thanks and greetings from Portugal.
@2WR
3 жыл бұрын
It’s up to you how you want to use it. All Personal preference
@julioporta5950
3 жыл бұрын
Nice video! I'm wondering if the accessory wiring in the 1290 is the same on 1190. Any thoughts about that? Thanks in advance!
@2WR
3 жыл бұрын
Exact same
@lecramred4453
7 жыл бұрын
There is also an ACC 1/2 connection under the rear seat. I dont know where to use it for, but it is there.
@2WR
7 жыл бұрын
Yep. You can use it to wire in a plug for heated gear, add a power outlet to the top case etc. I'm just glad they included some. Most of my previous bikes would require me to hack into the harness or run straight off the battery.
@VirusAlert0
4 ай бұрын
Can you make a shor video where is that acc 1/2 under the rear seat? Thanks
@leecabell3375
7 жыл бұрын
New 1290 SA owner. Like the vids. Very helpful. Have you ever looked into installing a PDM60 to control your accessories? Wanting to install one for extra lights, gps, heated gear, etc. Any tips or insights on where to install the module and get the power? Thinking from the ACC connections under the seat. Thanks
@2WR
7 жыл бұрын
No. I don't run heated gear or aux lights and the GPS draws very little. Your best bet is under the seat as there should be space and it's already prewired. You could also plug it in near the power outlet up front.
@ronanrogers4127
6 жыл бұрын
Lee Cabell ...I installed the PDM60 about a year ago without any problems (easy install & fault free). I power my LED Light Bar; Givi S320 fog lights; Garmin Zumo 590; and my Pro-Oiler pump and gps module for brilliant automatic chain lubrication and cleaning. It’s been perfectly reliable. I considered the Neutrino overkill for my needs.
@roadpanzir
7 жыл бұрын
Well done, an engineer that I work with gave me a good tip, in much of the world "ground" is known as "earth" the earth or soil is brown so brown wire = ground wire.
@2WR
7 жыл бұрын
Makes sense. Funny thing is most of my other bikes and cars I've owned had all had black as the ground.
@roadpanzir
7 жыл бұрын
It may be a EU thing, like an iso standard.
@dimosk7389
3 жыл бұрын
@@roadpanzir depends on the application. on buildings, ground is always green/yellow. it is crucial to have the same color since 220V can kill you. 12V is harmless. thats why on cars and motorcycles, it is usually brown or black, but some manufacturers use different colors.
@stuartgladstone9204
5 жыл бұрын
Thanks for the video, just wondering if it’s easier to run cables from the rear 10amp auxiliary circuit to a tank bag rather then remove head lights etc. just want to charge phone etc in tank bag.
@2WR
5 жыл бұрын
So, I don't believe you'd have to fully remove the headlight to get to the front aux wires. (I had mine removed for other purposes). Running from the rear of the bike is a possibility but I'd likely run mine from the front to keep the leads shorter, easier to inspect and less susceptible to damage.
@stuartgladstone9204
5 жыл бұрын
Thanks for the reply , I removed the front head light and found the acc1 and acc2 , it’s easier to install from the front. think I will do the cyclops LED upgrade at the same time . Cheers . I have the 2017 1290 super adventure t
@RoadKing05FLHR
3 жыл бұрын
So as I have seen on different forums Acc2 is rated for 1 amp. I can't find details in the manual but the power supplies for Acc1 and Acc2 are both on fuse 2, 10A. My phone charger I'm hooking up may exceed 1 amp so I am going to hook up a relay. So, as far as the relay goes I was thinking I will hook up Acc1 positive and ground to the relay pin 30 + and 85 -. So the hot wire from Acc2 goes to 86 and 87 powers the charger. I am thinking the charger ground can go to 85. That leaves Acc1 ground disconnected. Not sure if it also needs to go to 85.
@MemphisMike901
7 жыл бұрын
Thumbs up on Intro!!!
@2WR
7 жыл бұрын
+MemphisMike thx Mike!
@davidvm9712
2 жыл бұрын
Hey bro! I tried plugging aux lights into acc 2 but when i turn them on they just blink like 4 times and then go off . Do you have to program something with the scanner? Or something like that?
@2WR
2 жыл бұрын
U u have a switch in-line?
@davidvm9712
2 жыл бұрын
Sorry bro, it was my mistake at the relay! Thanks a lot! 👍👍
@jgoogleheim8880
5 жыл бұрын
I'm changing the stock horn on my 2016 KTM SA to a denali soundbomb and I have the denali wiring harness with relay, battery connections, and red and blue male spade terminals for the oem horn.. The stock horn has a brown wire (negative ground?) and white (or light blue positive wire? ). Can I connect the blue denali to the brown oem and connect the red denali to the white oem and have only the denali horn work properly? There is an option to use posi-tap connectors so both the denali and oem horns sound together. Thanks for any advice, JT
@2WR
5 жыл бұрын
Hopefully the new horn came with some instructions as to which is the positive and ground wire but in any event, it should work plugging it into the factory hookup. When it comes to picking up both the factory and aftermarket horn...maybe. The ECU on this bike doesn't like surprises so it's possible it may throw a code but it's also possible it may work fine.
@jgoogleheim8880
5 жыл бұрын
Found an online instructions for the harness that warned that the KTM Canbus is very sensitive so wiring in parallel with included posi-taps may be needed. Ordered some wiring supplies to beef up the mini KTM oem horn wires where brown is the ground. Going riding and saving the denali for the next rain event. Getting out of the garage!
@andreybelous9880
7 жыл бұрын
The same set of wire also located under passenger sits in the back. Close to stop light.
@2WR
7 жыл бұрын
yep, they've provided multiple hook ups.
@saiganesh1919
6 жыл бұрын
Im looking to add a mobile charger to my duke 250. Got "Accessories 2.1&2.2" and "Accessories 1" wires at the bottom of the tank. Is the "Accessories 2.1&2.2" same as that of the acc2 that you told? Can I connect this 12v charger to "Accessories 2.1&2.2"?. Also are these wires fused?
@2WR
6 жыл бұрын
I know for sure ACC1 has a 10amp inline fuse. I don't believe ACC2 does so you may want to put one in. I can't give you a 100% answer to your first question as we don't have that model in US but you can easily test them with a voltmeter.
@danhill7525
7 жыл бұрын
Where would you recommend hooking up a set of auxiliary lights? nothing too taxing on the system most likely less than
@2WR
7 жыл бұрын
Dan, will they have their own on/off switch?
@justcruisingalong7112
7 жыл бұрын
2 Wheeled Rider I have the same question about the lights. Mine have an on/off switch and a skene for dimming. I am trying to prevent any issues with throwing a code. Thanks!
@2WR
7 жыл бұрын
I would plug them in using the ACC 2 connection up near the headlight. That way the Aux lights will automatically kick off when you kill the switch saving you from a drained battery. You'll still be able to manually control them with their dedicated on/off switch while the bike is running. You shouldn't have any issues with the bike throwing a code. KTM provided those pre-wires connections specifically for extra lights or electronics that they knew some of use would want to add.
@justcruisingalong7112
7 жыл бұрын
2 Wheeled Rider thank you. I really appreciate your assistance.
@luisgdoc
3 жыл бұрын
Hello Mario, we have also a 2016 1290 SA. I want to ask you if I can connect a pair of led auxiliary lights on the Acc 2 wiring. Thank in advance. PS, I'm subscribed to your channels.
@2WR
3 жыл бұрын
Sure can.
@vladiorgu9632
3 жыл бұрын
Hey Mario, do you think it's the same wiring on a 1050?
@2WR
3 жыл бұрын
Yep. I've found them to be the same on all of the KTM big bore ADV bikes so far.
@NoobRoutz
5 жыл бұрын
Hey mate! Where did you run the cable out to the gps?
@2WR
5 жыл бұрын
I have an entire video on wiring the GPS kzitem.info/news/bejne/uqJmtKiDjmKYm34
@achbeir
6 жыл бұрын
hey, how do you have a video on how to wire a 12V power socket? thanks
@2WR
6 жыл бұрын
No, but all you need to do is decide if you want it constant power or acc power and hook up the ground and hot wires.
@achbeir
6 жыл бұрын
2 Wheeled Rider hello again. I tried finding a bike specific (1050 adv) power socket, but came up short. Did you use any particular branded one or just any 12v power socket which fits the cut out next to the dash works? Thanks
@dgravatt
7 жыл бұрын
A day after watching this video I noticed that some of my excess gps wires slipped out of where I have them tucked. I wish Garmin either offered a cradle with power connections only or if the cradle allowed you to disconnect wires you do not intended on using.
@2WR
7 жыл бұрын
The wiring harness on this thing is ridiculous. While I was rewiring to ACC2, I retucked the wiring harness as mine too had started to come untucked (happened after I did the headlight upgrade as before that I'd had zero issue). I believe I got it tucked for good now. I added a couple zip ties to get things held better. We'll see...
@dgravatt
7 жыл бұрын
2 Wheeled Rider Same for me. Before the headlight upgrade it was fine. Next time I pull off the tank I may run the GPS to the connectors in the tail, I figure the extra run will reduce the size of the bundle and what's left can go in the tail.
@venusiian
6 жыл бұрын
I got the sumo 395 LM, and it came with this power cable, which is awesome: www.thegpsstore.com/Garmin-12v-Hardwire-Power-Cable-for-Zumo-P5574.aspx
@czondag
6 жыл бұрын
Question: for acc connection, do i need 4.8 or 6.3mm cable shoe maleconnector?
@2WR
6 жыл бұрын
I don't know off hand. I have an entire kit of electrical connectors so just grabbed out 2 that fit.
@davidmeadows5665
4 жыл бұрын
6.3mm standard spade connector
@tmark1301cc
7 жыл бұрын
Also, same connections available in the tail section.
@2WR
7 жыл бұрын
yep, they've provided multiple hook ups.
@kdemotorsports
6 жыл бұрын
Thanks sharing this. I have a 1090 and this is helpful to see how to get things. I have the 12v outlet on order and a gps mount I want to hardwire. So I'll need to do the same for both of these items. Sub for sub?
@2WR
6 жыл бұрын
Glad you found it helpful. I can't remember if I mentioned it in the video but the same connections can be found under the passenger seat as well in case you wanted to hook up a device in the rear of the bike.
@kdemotorsports
6 жыл бұрын
2 Wheeled Rider thanks if you did I missed that part. Excellent to know because I will probably hook up my heated gear there instead. Right now I use my trickle charger connector and it doesn’t work so well given the cable positioning.
@Clickmaster5k
5 жыл бұрын
Have you wired a 12v socket in the rear top case?
@2WR
5 жыл бұрын
Funny you ask...the part has been sitting on my work bench for over a month. Just trying to make the time to install it.
Пікірлер: 71