hi Kleo Love U BRO Nice work, bro, but I was surprised that 360 mm AIO and 240 mm AIO have a difference of only 1 or 2 degrees (between A and D) with an average of 5 ghz. Please explain to us for information purposes.
@KleoYan
9 ай бұрын
Hi Always Respawn, let me start off with the case structure. If I am not careful enough to choose the correct airflow. Having a 360 Liquid AIO is deem better performance to a 240 liquid AIO, but you need to have good airflow in your case. You see, if the heat can't dissipate fast enough, the metal of this case will absorb the heat, since the radiator is attached to the case side, these heat will more or less transfer to your 360 radiator, plus the factor of larger surface area of the radiator, It asborbs more heat. though there is a side panel with mesh holes, there are restriction to the amount of hot air exhausting or cool air drawing in. As why the 240 is doing pretty good. it's located at the rear where there are no gaps, plus the honey comb holes are larger compared to the mesh holes at the side, therefore pushing hot air through the radiator and through the rear honey comb is fast, same applies if you draw cool air in to the radiator. Now for a 360 liquid AIO not being able to perform is when a case has restriction of airflow. If you case have proper airflow, the amount of cool air in is equal to the amount of hot air out. Your 360 radiator will out perform a 240 Liquid AIO. I hope these make sense as it took me a fair amount of time to figure out how to run a 7950X at an acceptable temperature in this chassis and not only that, I have to battle with my room temperature too, as the case is made of metal and it is also absorbing some heat from the exterior.
@AlwaysRespawn
9 ай бұрын
@@KleoYan oh I see ,so bro we can use galahad ii Trinity 240 with 7900x or 7950x for all core 5 or more ghz of performance. If I am not correct so please correct me.
@KleoYan
9 ай бұрын
@@AlwaysRespawnyes you can use the 240 GA II trinity, but will need to tune the PBO2 to set the PPT at a lower wattage consumption. Also the TDC and EDC to draw lower ampere. Just like how I illustrated in this content. But this will limit the potential of your highend processor. Again the choice is yours.
@khlo0od99
3 ай бұрын
I stopped the video when I saw the results window to come here and say THANK YOU for this.
@KleoYan
3 ай бұрын
Hi khaled, welcome to my channel and thank you for your feedback.
@Trapped-in-polaroid
9 ай бұрын
You are the first person I've seen to do in depth testing on the o11 vision's thermals. Cheers for that. Only thing I wish was included is tests for air cooled configurations, as I am unsure if this case would be good for that.
@KleoYan
9 ай бұрын
Hi Trapped-in-polaroid, welcome to my channel. If you want my honest opinion, I will not advise you to do aircooling. Maybe someothers will have the expertise on this. For me when I did the test on a aircooler, there is no way I can get it below 95 degrees, unless i set drawing wattage is at 125watts. Do note that I am not only battling with the airflow of this case ( got to plan properly to have balance airflow) I have to battle with my harsh room temperature too. Unless you are in a colder country, aircooling is possible. You see, in such a warm room, the case will absorb heat from the exteral too. Thank you for your question and am glad you've bring this up.
@Trapped-in-polaroid
8 ай бұрын
Thank you for the reply! I can understand your reasons for going watercooling. I don't have problems with high room temperatures and my CPU doesn't produce as much heat as yours so I imagine it will be ok. Just don't want to spend another $100+ on an AIO, especially since they tend to have less longevity than air coolers. I think I will stick with the air cooler I already got.@@KleoYan
@KleoYan
8 ай бұрын
@@Trapped-in-polaroid I see. Understood. Yup if you are at a cooler region, it will be fine 😉 thanks for the update.
@mvargast
2 ай бұрын
Thanks for this bro!! Exactly what I was looking for. I'm impressed that A was the winner
@KleoYan
2 ай бұрын
Hi Marino Vargas, welcome back and thank you again for the feedback. All the best with your build. 😉
@DerekAllDigital
8 ай бұрын
This was very comprehensive without being overbearing. Well done.
@KleoYan
8 ай бұрын
Hi Derek Brown, welcome to my channel and am glad you like this content. Thank you for your valuable feedback and all the best with your build too.
@jenarobzen
6 ай бұрын
Mannnn, you such a badass, and you are very high worth to receive the Nobel price for this video. Thank you so much for this 🙏🏻🙏🏻🙏🏻
@KleoYan
6 ай бұрын
Hi Jenar obZen, welcome to my channel and thank you for your valuable feedback. All the best with your build too 😉
@freshdripz4670
3 күн бұрын
Solid video, good shit my guy. I was looking for some one doing the D configuration and vs A and B configuration was money. Thank you
@KleoYan
3 күн бұрын
@@freshdripz4670 hi welcome to my channel and thank you for your feedback. All the best with your build too. 😉
@xantech42
4 ай бұрын
I just bought the o11 Vision and was worried about how I wound have the fans set up….your video was a big help!….you have yourself a new subscriber….keep up the great work 😎
@KleoYan
4 ай бұрын
Hi XanTech, welcome to my channel. I am glad you like my content. Thank you for your valuable feedback and all the best with your build. 😉
@RajK09
Ай бұрын
Thanks alot, this gives a clear picture on how to configure airflow in Lian Li o11 Vision case.
@KleoYan
Ай бұрын
Hi Raj K, welcome to my channel and I am glad you like this content. All the best with your build too.
@Marceles45
2 ай бұрын
Thanks for the video, I'm set up at B but after this I'll probably end up switching my fans
@KleoYan
2 ай бұрын
Hi Crotin, welcome to my channel. I am glad this does aid you in certain ways. All the best with your build too. 😉
@cameronfreeman6753
4 ай бұрын
This was incredible. Thank you so much for providing this info.
@KleoYan
4 ай бұрын
Hello Cameron Freeman, welcome to my channel. I am glad you like this content and thank you for your valuable feedback. All the best with your build too! 😉
@TheDaveyd29
2 ай бұрын
mate you are a legend for doing this, thank you so so much
@KleoYan
2 ай бұрын
Hi daniel davey, welcome to my channel and I am glad you like this content. All the best with your build too 👍👍👍
@k2nezumi88
2 ай бұрын
Thank you so much for this video, helped me to decide to pass on this case, even though I really want it for the looks. I live in Beijing and it's too hot in the summer for my peace of mind.
@KleoYan
2 ай бұрын
Hello k2Nezumi, welcome to my channel and thank you for your feedback. 👍👍👍
@christianl3592
2 ай бұрын
Glad I came across this review. I’m planning on upgrading my system to a 4090 and 14900k, and this case, although beautiful, will not do any good. Love your channel and way of detailedly explaining things. I’ve actually made most of the planning for my new build around your reviews. Thank you!
@KleoYan
2 ай бұрын
Hi Christian L , welcome back and thank you for your feedback. I am glad some of my content did help you in someways. All the best with your build too 😉
@Den_KDA
Ай бұрын
I have some interesting observations with the rear fans. If you don't install them at all or install only the rear top one, then your M2 SSD will have lower temperatures than with a fan. This is when installing the remaining fans, of course. That is why in the test in options D, E, F the M2 SSD is hotter. The additional resistance of the radiator further interferes with the free flow of air. The back grille is the only place where the air comes out and should come out. If you are not bothered by the noise level, then set the rear fans to high speeds - this will greatly increase the cooling efficiency.
@KleoYan
Ай бұрын
Hi Денис Косов, welcome to my channel. Thank you for your sharing, greatly appreciated it. You've sharp eyes. 👍👍👍
@arkaneforyou
20 күн бұрын
Thanks for making this video !
@KleoYan
19 күн бұрын
Hi Arkane, welcome to my channel. It's my pleasure to share the experience and all the best with your build. 😉
@larrydubill
27 күн бұрын
Great content! I am doing the 011 vision with set up A.
@KleoYan
26 күн бұрын
Hi Larry Dubill, welcome to my channel and I am glad you like this content. All the very best with your build too. 😉
@GabrielGraph
5 ай бұрын
Thank you so much the best video I see for 011 Vision case airflow
@KleoYan
5 ай бұрын
Hi GabrielGraph, welcome to my channel and thank you for your feedback. I am glad you like the content and all the best with your build too. 😉
@DRSUTTON
2 ай бұрын
Great job! Enjoyed every bit of this video.
@KleoYan
2 ай бұрын
@@DRSUTTON hi, welcome to my channel. Thank you for your feedback and I am glad you like this content. All the best with your build too 😉
@GermanArchitect
5 ай бұрын
thank you for testing the fan positions! I was looking for that for my O11 vision build
@KleoYan
5 ай бұрын
Hi ehMKay, welcome to my channel. Thank you for your feedback and all the best with your build.
@GermanArchitect
5 ай бұрын
@@KleoYan thanks. I could not believe, that 6 intake and 2 exhaust is good, while sucking the warm air from the radiator in (Setup B), but I guess thats the way to go :D
@KleoYan
5 ай бұрын
@@GermanArchitect nice. That’s good. You found a good sweet spot 👍
@GermanArchitect
5 ай бұрын
@@KleoYan Yeah, now I just have to figure out how I get my 4090 FE in vertical mode into it. Any chance to do this while having 2 rear exhausts?
@KleoYan
5 ай бұрын
@@GermanArchitect for me nope. Not possible. The 4090 height is too tall.
@junruihe8647
3 ай бұрын
Thank you so much for testing all the fan configurations on the O11 Vision, been wondering this myself. I know you mentioned air cooled cpu being unsuitable for your region's weather, I assume the result would be similar to config D, since the CPU fan position is similar to the AIO out. I am surprised though that even with 24AIO its better to exhaust, instead of drawing cool air right from outside the backside
@KleoYan
3 ай бұрын
Hi Junrui He, welcome to my channel. Yup I did mentioned that is not ideal to have aircooling in my country. and as for the 240 exhuasting air out instead of drawing air in, the trick is to push hot air out of the case. if you have set it to intake with a 240 at the rear. the hot air will need to exit from the side but it's far reach plus of the angle. Therefore having side intake to bring in cool air and to have rear to exhaust is more ideal, as the warm air is around the motherboard area where the direct path to draw hot air out is at the rear.
@naomy1701
8 ай бұрын
about as expected (but not without surprises i admit), thx for sharing ^^
@KleoYan
8 ай бұрын
Hi ɳɐɸɱɣ Ɖᴙσאϵ, welcome to my channel but if you do push pull configuration on a 360. It might work. thank you for your feedback.
@ali021
6 ай бұрын
Just subbed to your channel, just got this case yesterday and was thinking of going with the B configuration. Will probably have to do A now 🙏🏽
@KleoYan
6 ай бұрын
Hi Ali Rezai, welcome to my channel. That's good, wish you all the best with your build and thank you to have subscribed to my channel.
@noxmu4715
9 ай бұрын
I like your guts Kleo. You speak from your heart, telling others not to use a highend processor in this chassis, which is based on weather condition. This does shows the value as why I will listen and to watch your content. I have a question, ain't you worry to lose sponsorship when you speak this way? By the way, another excellent content, thank you for sharing 😘
@KleoYan
9 ай бұрын
Hi Nox, welcome back. My conscious is clear and I strongly believed that there are always room for improvement. Not being bias, Lian Li do listen and to improve on their products. Another factor, I find no point to do an overview which exclude the cons. My channel is based on 3 principles. 1st being honest, 2nd info which PC builders want to know and 3rd as a guide content. Nox, thank you for being supportive from the start ❤
@noxmu4715
9 ай бұрын
@@KleoYan well spoken, you are the type of person whom I will trust and to work with. When it's good or bad, you will stand neutral. Thank you for your time and efforts to share these info. 3 👍👍👍 up.
@AngelOfEcstasy
8 ай бұрын
Hello! Well done! Thanks! For my opinion, configuration - "C" is better choice for me, BUT with minor changes: 1) 2x120 fans on rear (low m/b position) 2) 3x140 fans on bottom (AL also exists in version 140) 3) Vertical GPU orientation (with rizer) for stronger airflow from 140 fans which will cause a better effect on m/b temperatures... but more for appearance :) I think O11 Vision too big for 3x120 on bottom. It also has little ventilation. Thats why it needs more air volume and airflow speed. I will glad to read your opinion about this :)
@KleoYan
8 ай бұрын
Hi 怪獣, welcome to my channel and thank you for your valuable feedback, I am not really happy with the results and intend to do another content to test out some stuff. I will test out your method too. Thank you for your suggestion.
@ali021
6 ай бұрын
@@KleoYanHello, I really appreciate the thorough testing in this video! Have you been able to replicate these tests with 140 fans at the bottom?
@KleoYan
6 ай бұрын
@@ali021 hi, welcome to my channel. Do pardon me, I have not test the 140mm fans at the bottom and this case no longer with me, so sorry.
@ali021
6 ай бұрын
@@KleoYan no worries, thank you for the great content. This video was very helpful 💯
@KleoYan
6 ай бұрын
@@ali021 you are most welcome and all the best with your build too.
@young-j731
8 ай бұрын
9:25 A is the Best... Best Cpu and Gpu Temp 3x120 bottom (air in) 2x120 rear (air out) and 360mm push and pull on side (air in)
@KleoYan
8 ай бұрын
Hi Young-J welcome to my channel and yup A is still best. Thank you for your feedback 😉
@8minimal8
8 ай бұрын
Thank you so mutch for your work here! helped me alott!!!
@KleoYan
8 ай бұрын
Hi Philipp Trillenberg, welcome back and I am glad this did aid you in someways. By the way, it will still be good if you can test it out yourself as my country climate might be different from yours. All the best with your build 😉
@8minimal8
8 ай бұрын
thank you! i will do that @@KleoYan
@KleoYan
8 ай бұрын
@@8minimal8 you are most welcome 😊
@allhailcowcow
3 ай бұрын
Hi!, I love this comprehension down on the thermal test. Originally, I was going to do a push and pull configuration on my aio in this case but was thinking against it due to it taking too much power having multiple fans and stuff. A quick question however, is how did you set your aio to do the intake if it's a 360m? (Sorry i'm still at a basic level for pc building if you can't find the time to respond it's fine!)
@KleoYan
3 ай бұрын
Hi Allhailcowcow, welcome to my channel. The nature of this case, you will need to use brutal air pressure to push air from the side and to exit to the rear. I have done a pull configuration on the AIO which is drawing air from the side but going through the rad. Though pulling warm air instead. My cpu temp was ok where I have to limit the power drawn on my processor. I believe is I do push pull configuration, the temperature will go down. Let me be very honest. I perfer to use the O11D EVO RGB case compared to this case as the airflow is so much better in that case. Bottom line is, if you want aesthetic, you will need to accept the compromised temperature with this case. If you want better temp, the O11D EVO RGB is the way to go.
@tommarshall9927
7 ай бұрын
Thank you for this video, very helpful!
@KleoYan
7 ай бұрын
Hi Tom Marshall, welcome to my channel and thank you for your valuable feedback. All the best with your build too 😉
@SirMic4711
7 ай бұрын
Very nice test. The general problem with this case is the lack of a dust filter at the front side. There are only dust filters on the bottom. I still don't get why. So if you want no trouble with dust you can ONLY suck air in through the bottom and blow it out at the front side and to the rear.
@KleoYan
7 ай бұрын
Hi Michael Sirtl, welcome to my channel. Unless you are in a cool room and to use not highend pc products which generate lots of heat. Then it will be alright to have mesh. Anyway I agree with you and maybe should to regular maintenance to keep dust from accumulating.
@SirMic4711
7 ай бұрын
@@KleoYan RX 6900XT and Ryzen5 5600X. So this stuff gets quiet hot...
@KleoYan
7 ай бұрын
@@SirMic4711 I see, then that should be ok to have dust filters. I believe lian li has it's purpose not to have those filters but you can always DIY. it's not difficult which I did for another case, which is the Q58 kzitem.info/news/bejne/rYJ3nY2YsGNld5gsi=TnKJcL7DIdniwVwz&t=874 matterial can be found and it's not expensive www.amazon.com/MoKo-400x300mm-Dustproof-Magnetic-Computer/dp/B0BHSS55RM
@shivang0017
9 ай бұрын
Your content quality is growing like a cute little baby. Such good-quality content. Keep it up, bro, and btw, which thermal compound did you use in this test? Also, I have one more question: is lianli galahat trinity ii 360 (standard) and lianli galahad trinity ii 360 SL-inifnity the same in performance?
@KleoYan
9 ай бұрын
Hi Shivang001, welcome back and thank you for your valuable feedback. Your motivation words will encourage me to bring better content. Thank you! As to answer your question. The air pressure of any Uni Fans are better compared to the standard fans, thats part of the reason, I've make use of the AL120 V2 fans.
@shivang0017
9 ай бұрын
@@KleoYan thanks for the reply and bro which therrmal compound u use in this test
@KleoYan
9 ай бұрын
@@shivang0017 I am using the IC Graphite Thermal Pad. Most of my benchmark test and such are using this, just to standardised the result when testing liquid cooler or aircooler.
@shivang0017
9 ай бұрын
@@KleoYan Bro, If you don't mind, can you please make a video of the ic thermal pad vs. the arctic mx-6 for our understanding purposes? It will help us.
@KleoYan
9 ай бұрын
@@shivang0017 hi I have mentioned in couple of occasion. Using the IC Graphite thermal pad will never be as good as thermal paste. This is one good example you can witness. kzitem.info/news/bejne/onyh04aFhImop44si=q06F-IHFUhqqPe4g
@dedejmen
23 күн бұрын
Many thanks for this comparison! I assume you placed your mobo so that it can fit 2 fans on the back for setups A-C, correct?
@KleoYan
23 күн бұрын
Hi Dejmen, welcome to my channel and yes I have place the motherboard so that I can fit 2 x 120mm fans as this case lack of exhaust..
@wumpratt
8 ай бұрын
the side radiator panel can mount 6 x 120mm per lian li's official website. in front and behind the radiator
@KleoYan
8 ай бұрын
Hi wumpratt, welcome to my channel and yup. It's written in my description. I will be doing up another test with push pull configuration. thank you for the information.
@Justme-jp8ih
8 ай бұрын
Really great video, thanks for the effort! I was really curious about the temps, bcs I wanna build a pc with this case and a 4090
@KleoYan
8 ай бұрын
Hi Just Me, welcome to my channel and thank you for your valuable feedback. Now this test is conducted in a hot and humid country. If you are in a region where is cooler. The temperature readings will be lower.
@pcguru.1
2 ай бұрын
Damn what are you filming with? That B roll in the dark looks crisp af
@KleoYan
2 ай бұрын
Hello Pc Guru, welcome to my channel. Is just an iPhone XS with ProMovie Recorder App. 4K 60fps with iso 320, white balance 4250 and shutter speed at 80. Then compress 4k 60fps to 2k 60fps.
@Gakoranus
6 ай бұрын
Having your radiators blow air into the case is... foolish. The purpose of the AIO is to move heat out of your case, not back into it. The A and E tests can be safely discarded which makes them look much more reasonable.
@KleoYan
6 ай бұрын
Hi Gakoranus, welcome to my channel. Thank you for your feedback 😉 nevertheless have tested and results are there. Why not do some testing, to post your content and to share them with us, so that we can learn from you too 😉
@Aiyahhhh
4 күн бұрын
Thanks for doing this. I have mine set up in the blue C configuration.. but now you’re having me question whether or not to switch the AIO to intake… I built the PC for a friend who I know isn’t going to be doing any overclocking so I’m thinking it should be fine as-is. Thoughts?
@KleoYan
4 күн бұрын
@@Aiyahhhh hi welcome to my channel. Overall if you are having good temps. You can leave it. Plus I am testing this out in a hot and humid country, where throughout the year, we do not have 4 seasons. It’s always summer. Room temperature is always high at 30degrees celcius.
@Aiyahhhh
4 күн бұрын
@@KleoYan thanks for the reply! It’s pretty hot and humid where I’m at too, but we do have seasons, it’s in an air conditioned house that’s always cool, so it’ll probably be fine. I set up the AIO as exhaust for dust reasons because he has a lot of dogs lol. I don’t think my friend is tech-savvy enough to notice a 2° improvement even if I flipped the fans 🤣
@KleoYan
4 күн бұрын
@@Aiyahhhh you are most welcome and yup if you are having good temp, just leave it will do 😉
@VaggosWho
2 ай бұрын
It looks great box!The Fans are included in the box, or you have to buy them?Also is it ok for Motherboard Z790??
@KleoYan
2 ай бұрын
Hi Βαγγέλης Γιανν, welcome to my channel. The fans are not included and for Z790 board. you can place it it no issue.. just have to be careful on processor you use. As the thermal for me in my region, is not that great.
@Ray-yn4ty
7 ай бұрын
very helpful video 👍 im gonna buy this case, with my undervolted 5800x3d (Max 85 Watt) and RTX 3080 i guess i will not have a heat problem at all
@KleoYan
7 ай бұрын
Hi Ray98, welcome to my channel and yes, you are correct. the 5800X3D is not a toasty processor and plus UV, this vision is suitable of it. All the best with your build and thank you for your feedback.
@Ackz89
4 ай бұрын
Really useful video! I'm looking at building B or C, can i ask - did you use all 120 fans for the test? I'm looking at using 140s for the bottom intake, would it have much effect on the results? A is clearly better, but it would require buying 3 reverse fans or spinning them around showing the back. Thanks!
@KleoYan
4 ай бұрын
Hi Acky, welcome to my channel. All are of 120mm fans and if you use 140mm fans. There will be more or less some impact, I would say the thermal might improve by 1 to 3 degrees but for sure your build will be quiet. Reason is, 140mm fans does not require high RPMs to draw tons of air.
@Ackz89
4 ай бұрын
@@KleoYan Thankyou for the reply! Subscribed due to the very informative information. I live in Australia, and have the same ambient temperatures as you, and now starting to have concerns about this case.. May opt for the mesh roof version just to have 3 extra fans. If i was to mix and match components, RGB would have to have separate programs? Don't think L Connect would be able to control an EK AIO for example right?
@KleoYan
4 ай бұрын
@@Ackz89 hi you are most welcome. for L-connect to work, you will need the uni fan controller from Lian Li as it has the firmware needed. for your EK AIO, you will need to use your motherboard utility to control the argb effects or alternatively, purchase an ARGB Controller. hmm, I didn't know the O11 Vision have the top mesh version or are you referring to the O11D Evo RGB? If you are using pretty highend products like processor or GPU, I suggest to get the O11D Evo RGB, it is more expensive but it's has better thermal. The choice is yours.
@Ackz89
4 ай бұрын
@@KleoYan Yes sorry, the O11D Evo, so it has a roof to exhaust and top mount radiator. I have a 3080 and looking at using that but the other parts are new and wanting i9 14900k.. so hot parts. Don't really want to spend the money on top components, to have to undervolt them.
@KleoYan
4 ай бұрын
@@Ackz89 I see, then the O11D Evo fits the bill more.. all the best with your build too. do let us know your experiences, once your build is complete 😉
@Shank_Sinatra
6 ай бұрын
This video was EXACTLY what I need. Thank you so much bro for making this and taking the time to do all this for someone who is about to make a purchase and doesn’t have the money to do it twice. You really are a real one for that. One question for you: Do you think ~5C on a 12700k would be worth setting my pc to be setup as “figure C” or “Figure F” for aesthetic purposes? Or are the reverse fans the way to go so I can have the looks and air performance? don’t you think Lian Li should offer the option for reverse fan config AIOs if this is how their new case is set to work best? I get all this glass just to look at the cage side of an Infinity mirror fan. 😂
@KleoYan
6 ай бұрын
Hi Phil Kannaly, welcome to my channel. It greatly depends on where you are from. As in a Hot and Humid country or from a country which is having 4 seasons. C or F will not yeild good results, it should be A or D. if you are of a hotter country, I will adivise you to do A with push pull configuration. Else if you are of a colder country A or D will just be fine without push pull configuration. As for the reverse fans for liquid AIO. I will feedback to Lian Li, decission is up to them.. or you can suggest this at their reddit forum. www.reddit.com/r/lianli/
@Shank_Sinatra
6 ай бұрын
@@KleoYan once again, you are the man. Thank you for your long, honest and quick response. Definitely just got a like and subscribe from me. I’m glad I found a new place to learn on YT. Have a great night.
@KleoYan
6 ай бұрын
@@Shank_Sinatra you are most welcome and good afternoon here .. sleep tight.. nite nite.
@shivang0017
9 ай бұрын
Hi Kleo, If you don't mind, I have an idea for your next video content. I searched on KZitem and found almost no content on the 7000 series processor with Air Cooler, like with the AK 620 or the Pearless Assassin 120 SE. If you make video content on this topic, I think your channel will grow at double speed. Your videos will easily be recommended by KZitem.
@KleoYan
9 ай бұрын
Hi Shivang, welcome back. I see what I can do as I did try to approach various brands for aircooler but failed. If I do get more air coolers. I will do up content. Thank you for your suggestion 😉 greatly appreciated it.
@jordanturner7821
8 ай бұрын
This was a great video. Thanks bro.
@KleoYan
8 ай бұрын
Hi Jordan Turner, welcome to my channel and thank you for your feedback 😉
@SupplyNinja
7 ай бұрын
Great video. Very informative. That CPU temp was high in all cases.
@KleoYan
7 ай бұрын
Hi Supply Ninja, welcome to my channel. This only apply to my region might not be the same if you are from a colder country.
@TheLemonyLime
26 күн бұрын
Im going with set up A but I like having one 120mm exhaust at the back. Do you think there will be a huge difference vs going with 2x 120mm exhaust? I just prefer using "high mode" for the mobo config.
@KleoYan
26 күн бұрын
@@TheLemonyLime hi welcome to my channel. To me it does in my country (hot and humid). This case is a toaster to me as it does not have top exhaust. By removing 1 fan off the rear, the thermal will be drastic. Unless your country is of a colder country.
@ashadsiddiqui3226
6 ай бұрын
Hi there! Firstly thanks a lot for this video! It’s very detailed and concise and you explained everything very well. My only question is about AIO coolant temperature. Right now I am stuck between position A and C (both have bottom 3 fans intake and rear 2 as exhaust, difference is side 3 intake vs exhaust). Most people believe that A is better than C as it lets more air come in. My my question is, isn’t that bad? The radiator on the side is getting hot and using that to intake air will make the chassis hotter no? Also how will these two configurations compare in terms of coolant temperatures for the radiator?
@KleoYan
6 ай бұрын
Hi Ashad Siddiqui, welcome to my channel and thank you for your feedback, I have another option for you. stick to A) but do it push pull configuration on your rad, that will help more in air circulation. your Coolent temp will be good plus hot air are forces out of the case due to additional set of fans, but if you choose to do one set of the radiator. I still would advise you to stick with A). Reason to this, coolent will be good and though hot air in going in to the case, you don't have to worry about GPU temp as it's taken care by the bottom fans. be it side intake hot air and bottom push in cool air, it's still postive air. if you choose C) that will be negative air. Just my opinion.
@ashadsiddiqui3226
6 ай бұрын
@@KleoYan Hey Kleo Yan, thanks for the reply! So actually after sending you my message I didn’t know when you’d respond so I tested A. I actually used to use C with push/pull (meaning 6 fans on radiator all exhausting) and my temps would be 66C on GPU and CPU. Now when I did A, I get the same GPU temps but CPU is like 5-7C better. Definitely seems this was the better option. Side question, what do you use to monitor coolant temps? I currently use armory crate form Asus (I have an Asus aio). The monitor from armory crate seems to be showing a wrong cpu temp for me so I don’t know if I can trust the coolant temp too.
@KleoYan
6 ай бұрын
@@ashadsiddiqui3226 I am using the Galahad II LCD 280 (push pull config) with L-Connect 3app, but is with another case. It’s accurate for me. Be it CPU, GPU. Which I do believe the coolant temp are accurate. Another thing I like to emphasis is, I do not overdose my build with too many ARGB which make use of too many controllers. Plus I never like overdose ARGB. The only device that uses L-Connect 3 is my LCD panel of the AIO. This is my fun build which I have mentioned. All temp readings on the LCD are accurate www.reddit.com/r/pcmasterrace/s/GG2vNo5EPD
@theopszone6775
5 ай бұрын
Hey friend, had to stop by, on this case. Thinking about upgrading my son's PC from the Corsair 4000d. Was wondering about temps, if I decided to keep his 240 aio. Great video.
@KleoYan
5 ай бұрын
Hello TheOpsZone, welcome back. the O11 Vision to me is a toaster. This is based on the experience I have in my region, I would advise to get the O11D Evo RGB. that's my opinion, but if you still choose to have this O11 Vision, I would advise to do side 360 with push pull configuration.
@jedemmalter9484
7 ай бұрын
Hi Kleo Yan, Thank You very much for this amazing video. In previous 5-7 days I am searching for proper explanation of best setup for Lian Li 011 Vison and could not find so detailed explanation regarding airflow and temperatures in this case. I am about to order this case, along with 7800x3d CPU and 4070/4070 Ti GPU. I love Lian Li AIO and fan solutions, so will go with it. However, still not 100% sure in which direction to go regarding AIO and fan setup. My initial plan was to use 3 intake fans from bottom and 1 intake from rear side with AIO (exhaust) on the side. It is Your "B" test case. However, after I saw Lian Li recommendation and after I saw Your video - I will probably go with "A" option. Probably, I will buy TL fans. Question for You, I would really appreciate Your feedback: Is it feasible to buy 360mm AIO, remove all 3 fans from it and use those fans as intake from bottom of the case and then to buy 3 TL LCD fans and mount them on AIO? On rear, I would put 2 exhaust TL fans (without LCD)? What do You think about this setup, especially having in mind chosen CPU and GPU and fact that I will use them on factory settings? (I am from Central Europe, room temperature does not go over 26-27°C) during summer. Thanks a lot for Your time for reading this and appreciate if You can give any feedback on this.
@KleoYan
7 ай бұрын
Hi Jedem Malter, welcome to my channel. Based at your region. I will adivse you with this configuration Either - Bottom Intake using Liquid AIO fans - Side with liquid aio exhuast with 3 x TL LCD fans - Rear intake 2 x TL reverse fans Or - Bottom Intake using Liquid AIO fans - Side with liquid aio intake with 3 x TL - Rear 2 x TL LCD reverse fans you see with 1 rear fan it will be weak but with 2 rear fans, it will push more warm air away from your motherboard area and to exist better at the side.
@jedemmalter9484
7 ай бұрын
@@KleoYan Thank You! ...and keep up the good work ;)
@KleoYan
7 ай бұрын
@@jedemmalter9484 hi and welcome back. Thank you for the feedback and will continue to put up good content. Thank you.
@farrelln3034
7 ай бұрын
Thanks bro
@KleoYan
7 ай бұрын
Hi Farrell N, welcome to my channel. my pleasure. all the best with your build too. 😉
@inmitch
7 ай бұрын
I would love to see a comparison of the Vision vs. the 011 Dynamic Evo and possibly even the RGB. Is this case worth the cost of thermals over the Evo or the RGB? I could handle a few degrees, but if it turns out to be maybe 10 degrees different I'm going with the Evo or RGB.
@KleoYan
7 ай бұрын
Hi Ian Mitchell, welcome back. I see what I can do, but just my opinion, for me which is based in a hot and humid country, I prefer the EVO or EVO RGB. As the top mesh will help a lot more.
@silentkillz
9 ай бұрын
can we have sound tests as well since lian li fans are notorious for their vibrations at higher RPMs and hugh dbs at least its the case with the SL fans
@KleoYan
9 ай бұрын
Hi Silentkills, welcome to my channel. will do, do pardon me which I left out on the noise profile. In future, I will do that on my benchmark test. Thank you.
@franciscomartinho3037
3 ай бұрын
always considered this, is it problematic if i just use this case with the outer glass on? I can open it as an open case and then should not be a problem with temps, or u neeed it closed so u can have the flow properly?
@KleoYan
3 ай бұрын
Hi Francisco Martinho, welcome to my channel. To have the tempered glass all on, night need to get high airflow fans to force the hot air out, which will be noisy. If Having it open, yes it will help in cooling, but to be honest, that defeats the purpose to get this case.
@HungHoang-bv9ib
3 ай бұрын
Nice video, i very like this
@KleoYan
3 ай бұрын
Hi Hùng Hoàng, welcome to my channel. I am glad you like my content. All the best with your build too. 😉
@gabrielcorso
9 күн бұрын
Hey man.. I’m looking forward to buy a O11 Vision, but I live in Brasil (tropical country) and got a bit worried about having to lower down power consumption.. My CPU is AMD 7 7800x3D, and GPU is a TUF 4070 TI Super.. Do you think I would need to lower my power consumption as well?
@KleoYan
9 күн бұрын
Hi Gabriel Corso, welcome to my channel. Just my opinion. I would rather grab the O11D EVO RGB over this chassis, so that I don't have to worry about it. Unless you are from a colder country.
@gabrielcorso
6 күн бұрын
Thanks a lot for answering!! Keep up with the great content. Those tests are really nice and useful. Normally temps on my region goes max 30°C.. and it’s not during a great part of the year.. Also the max clock speed for my processor is 5GHz That’s why I was in doubt..
@KleoYan
6 күн бұрын
@@gabrielcorso I see. hmm.. still I would prefer to go with O11D EVO RGB, but if your region do not always stay at 30°C and do have winter and such. The O11 Vision should not be an issue. The choice is yours and I wish you all the best with your build.. 😉
@Kadmos
3 ай бұрын
Thanks for doing the tests! Just got the case. Do you know if having 1 exhaust fan in the high position vs 2 exhaust fans in the low position at the back makes a big difference? With 360 AIO.
@KleoYan
3 ай бұрын
Hi Kadmos, welcome to my channel. To me it does make a difference. I can only tells you that this is based in the climate I am in as the only area exhausting the hot air is through the rear.
@salvadoralberti1372
5 ай бұрын
Hi Kelo, I'm waiting for my new PC. I have purchased the 360 Performance (3 fans) and 7 (3+3+1) 120 TL fans. The processor will be an i5 14600KF, the graphics card is a 4070 Super and the case is the Asus TUFF gt502. What distribution would you recommend? Your opinion would help me a lot. I live in Spain with a fairly warm climate in summer and somewhat cold in winter.
@KleoYan
5 ай бұрын
hi Salvador Alberti, welcome back. configuration as follow for GT502, btw I appreciate if you can post your question here instead kzitem.info/news/bejne/24CGl2F9kXaHZ6w , nevertheless, this is what I will suggest 1) Top with 360 AIO, fan exhaust 2) Side 3 x 120mm fans intake 3) Bottom 3 x 120mm fans intake 4) Rear 1 x 120mm fans exhaust.
@salvadoralberti1372
5 ай бұрын
@@KleoYan Thank you, I am learning a lot with your help. Congratulations for your good work.
@KleoYan
5 ай бұрын
@oralberti1372 thank you and you are most welcome. Alll the best with your build. 😉
@ArtemisTsukuyomi
8 ай бұрын
How do you think this case will do with a 7800x3d with a 360mm AIO set up? Live hot and humid country too with similar temps and deciding between the fractal design north or O11 Vision.
@KleoYan
8 ай бұрын
Hi Tsukuyomi Artemis, welcome to my channel, if you choose to use this O11D vision. You will need to use performance fans on a 360 Radiator using push pull configuration and also you might need to do offset vcore settings to -0.05v. That will sustain the temp and performance of your 7800X3D. It’s much cooler to run this compared to a 7950X. But which ever chassis you choose. By doing offset of vcore is the way to go.
@PhenomenalNFT
6 ай бұрын
Hey, Kleo! Great test! Could you give me a recommendation on the following: I am planning to use the "A" test case, but I am worried about my CPU Liquid Cooler as its' radiator is going to get hotter in a few hours of using. Won't it affect somehow? The fans will be intaking the hot air, won't they? One more question, will I be able to put 2*120mm rear exhaust fans with microATX form factor only? If I want to use Standard/Mini/E-ATX, won't I be able to put 2 rare fans?
@PhenomenalNFT
6 ай бұрын
Also, won't there be a problem with mounting a GPU vertically if I use 2*120 rear fans? I am going to buy RTX 4080 Super (most likely iGame Colorful).
@KleoYan
6 ай бұрын
@@PhenomenalNFT Hi welcome to my channel. for the side, place liquid aio with push pull configuration to force the warm air flow in and out of the case, this was the recommendation from Lian Li and I have tested it. it does help in termal. For ATX / M-ATX / E-ATX . no issue you can put 2 x 120mm fans. but make sure it's at low mode and not high mode of the motherboard. As for ITX I have not tried but I do realise the PCI-E slot for the GPU is at the 1st slot as compared to ATX / M-ATX / E-ATX which is at the 2nd PCI-E Slot. if you intend to Vertically mount your GPU, you will only be able to mount 1 x 120mm rear fan.
@PhenomenalNFT
6 ай бұрын
@@KleoYan ahh, not gonna risk mounting it vertically in such a case😅Did u buy the Vision Silicone Grommets Set for low mode motherboards or it was included in the PC case? Also, could you share the link for the push-pull recommendations from Lian Li? Couldn't find it 🤷♂ Thank you for the content you are providing! It's much easier to make some decisions if there are high quality tests!
@KleoYan
6 ай бұрын
@@PhenomenalNFTfor my demo set provided by Lian Li the silicon cover are provided separately.
@Elfy_Haikal
Ай бұрын
Hi bossku. i am planning to build a new pc with this o11 vision + many of the ARGB stuffs (i've already seen your Lian Li strimer connect to Controller hub video) but just wondering for this case? which is the better option fan for AIO? planning to use the 360 Kraken Elite. the fans itself will be the UNI-FANS. for AIO will it be better Reverse Blades or the Normal Blades? also since i am already here, will the Lian Li Controller hub be enough for 3 set of fans (2 fans on Back, 3 fans on bottom + 3 fans on AIO) + strimers (8pin connectors + 24pin)?
@KleoYan
Ай бұрын
Hi SwingGiantSwords, welcome to my channel. If you want good performance with looks. I will go for either TL or AL V2 fans. for TL fans as follow UNI FAN TL and TL LCD share the same controller, enabling the connection of up to 16 TL and TL LCD fans simultaneously, with a maximum of 6 TL LCD fans. I would advise you to read and understand fully if you using TL fans lian-li.com/product/uni-fan-tl/?fbclid=IwZXh0bgNhZW0CMTAAAR3LLuhvGXVOSDl12JaKGYQTzNJbAd3ZOtiOUMmqo1H_nPMcu56GGsa7DUk_aem_XsgD-2cHkf1ZUC4iMyozUw as for the rest of the uni fans like SL, AL or even SL Infinity. max is up to 16 fans with 4 fans to each port of the controller. this playlist might be what you are looking for. kindly look at the titles that has [L-Connect-3] as these are using the L-connect-3 app. kzitem.info/door/PLEW-b-2vYDdPo0NzHyeksx012c-nkDapm
@Elfy_Haikal
Ай бұрын
@@KleoYan Hi boss. You have shop in SG for me to bring down my PC? I've gotten the TL fans and TL LCD fans but L-Connect 3 is very wonky to control it.
@KleoYan
Ай бұрын
@@Elfy_Haikal hi and unfortunately nope, I do not run a shop.
@KingKxizen
8 ай бұрын
Thanks for the video, honestly I really want this but I'm hesitant with the possible temps I could get with a 4090 and 7950x3d. Its cooler in my room during the winter but knowing how hot the summers are, I don't know if its wise getting these over the 011 rgb... but I really like the look of this case :/
@KleoYan
8 ай бұрын
Hi Kaizen, welcome to my channel. Yes it does look good. A lot been telling me the cooling is good and such. You needs to put push pull configuration on a radiator to get better thermal results. If I am to put highend pc components, I will go for the O11D Evo RGB. At least there are more options to plan for case airflow.
@KingKxizen
8 ай бұрын
@@KleoYan Thank you for your advice and suggestion! I'll definitely go for that then!
@KleoYan
8 ай бұрын
@@KingKxizen you are most welcome. All the best with your build. By the way, I will be doing a build soon on the O11D EVO RGB. Maybe you like to subscribe and to click on the notification bell button. I Should be doing it this weekends.
@KingKxizen
8 ай бұрын
@@KleoYan perfect! Just subbed and I’ll wait to see your post!
@KingKxizen
8 ай бұрын
@@KleoYan Hi actually I wanted to ask another question, I was looking at my current PC and realised that I don't think the 4090 might need more power. I currently have the Corsair 850W PSU but I think the minimum is 1000W. Do you think I should upgrade and to which? I looked online and someone suggested the be quiet! 1600W but I think thats super overkill and expensive, unless thats not?
@armful
Ай бұрын
gonna be building in the O11 vision with a 4090 + R9 7950X3D - do you think i should go with the O11 dynamic evo instead?
@KleoYan
Ай бұрын
Hi armful, welcome to my channel. it all depends on yourself. Which do you prefer, outlook or with both. if you like the look of the vision. Go for it and tweak the airflow (Challanging) but if you just want both. O11D Evo RGB will be a very good choice. I will personally take the O11D EVO RGB over this vision.
@armful
Ай бұрын
@@KleoYan thank you! do you think thermals will be fine in the vision?
@KleoYan
Ай бұрын
@@armful For me at my region where it's warm throughout, it will be fine with mid tier prcoessor and mid tier GPU. but if you are at a colder region. It will be fine.
@oTheDucky89o
7 ай бұрын
I wonder if the casing is good for 14700K and 7900 XTX.. I'm from Malaysia which is also hot and humid..
@KleoYan
7 ай бұрын
Hi Kenny Yap, welcome to my channel. I would advoid using highend stuff in this chassis. if you run defualt settings without power limit of vcore offset. you won't get good temps. Only way is by brute force / airflow, that is to have push pull configuration on a liquid AIO at the side to push more air in and to force air out. 14700K runs hot at default.
@oTheDucky89o
7 ай бұрын
@@KleoYan I see.. In this case Lian Li O11 Dynamic Evo RGB will be better? I'm anticipating for your video review :D
@KleoYan
7 ай бұрын
@@oTheDucky89o Yup EVO RGB will be better in thermal. As for the review am still preparing as my work starts, having lesser time in content, unlike during the holidays. so sorry that you have to wait.
@oTheDucky89o
7 ай бұрын
@@KleoYan no worries, take all the time you need bro. Your content is very helpful for all builders around the world. Keep up the good work!
@KleoYan
7 ай бұрын
@@oTheDucky89o thank you.. I will try to keep up. 😉
@JJ-gk5tn
9 ай бұрын
Can't wait for the king 95 review man
@Ttblondey
9 ай бұрын
What is that
@Ttblondey
9 ай бұрын
Nice review
@JJ-gk5tn
9 ай бұрын
@@Ttblondey king 95 will be the best case in 2023
@KleoYan
9 ай бұрын
@@Ttblondey Hi welcome back, JJ is refering to this case, the Montech King 95 kzitem.info/news/bejne/kpCEva2GppGfkmUsi=17NGJii0enZvd_Df&t=169.
@KleoYan
9 ай бұрын
@@Ttblondey thank you for your feedback 😉
@liekarts2936
2 ай бұрын
How about the side push pull for the 360 radiator intake, bottom intake and rear exhaust??
@KleoYan
2 ай бұрын
Hi Liek Arts, welcome to my channel as based on my last test which is not listed. Having a 360 at the side with push pull configuration gets a better thermal result and it’s more ideal too.
@liekarts2936
2 ай бұрын
@@KleoYan oke, thank you very much dude
@KleoYan
2 ай бұрын
@@liekarts2936 you are most welcome and all the best with your build too. 😉
@LocksleyNg
9 күн бұрын
Hello Kleo, may I ask why did Style D's M.2 SSD suffer at 48 degrees when there's fresh air from the side while Style A has a lower one with the AIO being placed at the side.
@KleoYan
9 күн бұрын
@@LocksleyNg hi welcome to my channel. Part of the reason is the warm air circulating inside the case and with the AIO at the side, the airflow in has less pressure and allowing the rear to have sufficient time to push hot air out. If without the side AIO, there are no stoppage but forces circulation of warm air rapidly within the case itself. Is more like a dead trap of hot air. This is why the m.2 is has higher temp.
@LocksleyNg
9 күн бұрын
@@KleoYan So in this scenario specifically for the O11 Vision, it's better to have the AIO placed at the intake so that the back fans can properly properly exhaust the hotter air within the case right?
@KleoYan
9 күн бұрын
@@LocksleyNg yup. That’s right.
@LocksleyNg
9 күн бұрын
@@KleoYan Thank you for your in depth explanation. The community needs more thorough intake - exhaust placement tests like yours.
@KleoYan
9 күн бұрын
@@LocksleyNg thanks for the feedback. Something to take note of. This is taken in a hot and humid country. If it’s tested in a colder country. The result will be different. You see in my country, my room temperature is always at 30 to 31 degrees celcius. Therefore, even drawing air in, it’s of warm air not cool air. If you read some results from Lian Li’s Reddit forum. There will be peeps in cooler environment sharing their results too.
@Moonlight-zp5rj
6 ай бұрын
NZXT H9 elite or O11XL, which has better thermals , acoustics and better for custom water cooling
@KleoYan
6 ай бұрын
Hi Moonlight, welcome to my channel. do pardon me. I do not have the NZXT H9 elite, therefore I can't comment which is better. so sorry.
@pengdylee9631
7 ай бұрын
Lian Li AL V2 better than sl-inf fan?
@KleoYan
7 ай бұрын
HI Pengdy Lee, welcome to my channel. AL V2 are a bit better in static pressure but either fans you wont go wrong.
@huaitenhuang2053
26 күн бұрын
Hi Kleo Yan, I wanna use this case for my ROG Maximus Z690 Glacial Extreme with i5 12600K and will make water cooling PC, and using Lian li SL120 INFINITY. Can U help me to figure out the airflow for this spec and what GPU do U recommend? BTW my location at Indonesia
@KleoYan
25 күн бұрын
Hi Huai TeN HuanG, welcome to my channel. Go with setup A but if possible, for your Liquid AIO or custom watercooling radiator at the side, do a push pull configurattion. As for GPU, it depends on what you use your GPU for. I can't really recommend you a GPU as I don't play games at all on my PC. so sorry about that. But if you do lots of 3D rendering stuff, I will go for at least a 4080 Super.
@huaitenhuang2053
14 күн бұрын
@@KleoYan ty very much for your information 🙏 I'm using this PC for playing Dota 2 and using Adobe Illustrator, Photoshop, and Premiere Pro. I planned to use RX 6800 or RX 6800 XT Is it good enough?
@KleoYan
14 күн бұрын
@@huaitenhuang2053 for adobe suite application. It’s best to go with Nvidia at least a 4070 super.
@sandhyagupta5992
9 ай бұрын
Hi kleo I need your help, buddy. I am thinking of buying the Galahad II Trinity 360 Standard Edition for my 7900x. What do you think is that this AIO can handle the 7900x on all core Max clocks possible (5 GHz plus)? My ambient room temperature is 30-32 °C. Please help, bro.
@KleoYan
9 ай бұрын
Hi Johnathon J. Welcome to my channel. The reason I make use of the AL120 V2 is because of this reason. If I use the standard. I can’t even do 5ghz with the pbo2 settings
@twlsrovrdaar
9 ай бұрын
It would be great to see testing done with the 360 AIO and only 1 fan in the rear instead of 2
@KleoYan
8 ай бұрын
Hi T L, welcome to my channel. I see what I can do with another content to follow up. Thank you very much for the suggestion.
@joshmaag2457
8 ай бұрын
I believe techsource has a video of a build in this case with the orientation the way you are talking about and he had very good results. You can take a look if you want. He did a single intake on back and 360 intake on bottom with a 360 rad exiting the front side
@KleoYan
8 ай бұрын
@@joshmaag2457 hi and welcome to my channel. Thanks for the info, will have a look 😉 Infact have watch his but I guess is due to the region or maybe I am wrong. As I assume his room temperature is much cooler compared to mine. I have tired single rear fan but didn’t get better results. Thank you for your suggestion.
@twlsrovrdaar
8 ай бұрын
@@joshmaag2457 I already ordered Lian Li Infinity fans with reverse blade variants to build this with 4 instake (3 bottom, 1 rear) and 3 exhaust on my AIO in the front of the case before watching this video, so now I'm regretting my purchase on the fans lol. At least these fan layouts all produce acceptable results.
@joshmaag2457
8 ай бұрын
@@KleoYan yes he is in California with a temperature controlled room so that may have a factor in the matter
@rizen3553
7 ай бұрын
I'm sorry if Ihe mentioned it but did he use one or two intake/ exhaust fans in the back in the 360mm Rad tests?
@KleoYan
7 ай бұрын
Hi Rizen, welcome to my channel the rear is with 2 x 120mmn fans. I have mentioned the methodology I have applied. Kindly go through the whole content as I have indicated to test with the various fan positioning.
@kuzzzzzzzzzzzz7511
4 ай бұрын
Which case is the best thermal performance of all LIan li O11 line up??
@KleoYan
4 ай бұрын
Hi Kuzzzzzzzzzzzz, I would say it greatly depends on how you configure your airflow in a case. For me I will choose O11D EVO RGB.
@kuzzzzzzzzzzzz7511
4 ай бұрын
@@KleoYan evo rgb or nzxt h6 flow?? I saw a video h6 flow is better thermal performance
@KleoYan
4 ай бұрын
@@kuzzzzzzzzzzzz7511 I have no idea on nzxt products. So sorry.
@zeljkoignjatic2500
5 ай бұрын
Kleo Yan,i have rtx 4090 Gigabyte,i7 13700kf,Rog Ryujin 2 240. Do you recommend this case or should I go to Evo XL. I ask because of thermals.Sorry on my English,it is not my primary language😃
@KleoYan
5 ай бұрын
Hi zeljko ignjatic, the PC Parts you used will leave lots of empty space in EVO XL, I suggest you to get the O11D EVO RGB which will not look so empty. kzitem.info/news/bejne/0WirlqyVqmd0o2ksi=_l-ESVHp8m4oMS4d
@zeljkoignjatic2500
5 ай бұрын
@@KleoYan what do you think about Lian Li 011 Dynamic EVO,will there be high temperatures?
@KleoYan
5 ай бұрын
@@zeljkoignjatic2500 it’s up to you. I would go for EVO RGB. As there are more advantages 1st you can mount a 420 liquid AIO at the top as brackets provided and 2nd the anti shaq bracket that comes with the case is very functionable. If you have not watch my other video about the EVO RGB, go have a look 😉kzitem.info/news/bejne/0WirlqyVqmd0o2k
@lucklmfao4302
12 күн бұрын
for A set up does it have 2 exhaust right
@KleoYan
12 күн бұрын
Hi L., welcome to my channel. for Set A, your motherboard have to be at low mode and not high mode. Only motherboard at low mode allows you to mount 2 x 120mm fans at the rear.
@lucklmfao4302
12 күн бұрын
@@KleoYan thanks
@KleoYan
12 күн бұрын
@@lucklmfao4302 You are most welcome and all the best with your build too. 😉
@jimmykonti6419
5 ай бұрын
In option A, did you use 1x120mm or 2x120mm as rear?
@KleoYan
5 ай бұрын
Hi Jimmy Konti, welcome to my channel. Is with 2 x 120mm fans.
@jimmykonti6419
5 ай бұрын
@@KleoYan have you done any tests with 1x120mm fans? I want to put 1 and not 2, because aesthetically is nicer, and i wanted to see if it would have a major difference.
@KleoYan
5 ай бұрын
@@jimmykonti6419 if you are at a colder region, you can give it a try. As for where I am, by placing only 1 120mm fan. The cpu temp gone up by 7 to 10 degrees celcius.
@Xephaholic
4 ай бұрын
I have only 1 exhaust at the back , with 360 aio on the side and bottom as intake. Will it make a difference ?
@KleoYan
4 ай бұрын
Hi Xephaholic, welcome to my channel. If you are from a cooler country. There might be little impact but if you are at a warmer country like I do, then there will be a difference.
@Xephaholic
4 ай бұрын
@@KleoYan Hihi! Thanks Kleo for the reply! I live in Singapore and currently running only 1 exhaust in High Mobo mode. Is it possible for me to put 2 , 120mm at the back in high mode ?
@KleoYan
4 ай бұрын
@@Xephaholic hi and nope, if the motherboard tray is at high mode, you can't mount 2 x 120mm fans.. only at low mode.
@kourhu
2 ай бұрын
is it possible/okay to put 3x140mm intake fans at the bottom (instead of 3x120) while still putting 2 exhaust fans on the left side?
@KleoYan
2 ай бұрын
Hi kourhu senagaki, welcome to my channel. you can place 3 x 140mm fans at the bottom and still having 2 x 120mm at the rear, but be mindful that your motherboard must be installed in Low mode and not High mode for you to have 2 x 120mm fans at the rear.
@kourhu
2 ай бұрын
@@KleoYan thank you so much! i've been looking for an answer to that question. very helpful!
@KleoYan
2 ай бұрын
@@kourhu you are most welcome. All the best with your build too. 😉
@KleoYan
2 ай бұрын
@@kourhu you are most welcome. All the best with your build too. 😉
@KleoYan
2 ай бұрын
@@kourhu you are most welcome and all the best with your build too. 😉
@exilevic
8 ай бұрын
Hi, do you think we can mount the same 240mm aio to the rear panel on Lian Li DE XL as the same as your video?
@exilevic
8 ай бұрын
e.g., I would mount the cpu aio 360mm to the top and mount the gpu aio 240mm (asus rog strix LC rtx 4090) on the rear panel. do you think it's possible to put a 240mm radiator on the rear panel with lian li DE XL?
@exilevic
8 ай бұрын
I would presume since aio 240mm can be mounted to rear on o11 vision, then should be the same for o11 DE XL
@KleoYan
8 ай бұрын
@@exilevic Hi, welcome to my channel, I am not able to commit an answer for you as I have not touch that case before. I do not base on online manual and to do assumption. I am sorry sorry about this.
@exilevic
8 ай бұрын
@@KleoYan well noted, thank you for your replying!
@KleoYan
8 ай бұрын
@@exilevic you are most welcome. My feeling tells me that you should not try. as the O11 Vision is able to flip the PCI-E Slot to make space for the 240 liquid AIO.
@fisnikhoxha3114
6 ай бұрын
Would the temps be cooler if I use a lower end processor? I'm about to build in this case and I'm planning on putting a ryzen 5 5600x, do i still need an aio if i want to put it in this case?
@KleoYan
6 ай бұрын
Hi Fisnik Hoxha, welcome to my channel. It greatly depends on which country you are from. If you are in a cooler country, no issues with just using good AirCooler or Liquid AIO
@fisnikhoxha3114
6 ай бұрын
@@KleoYan I’m in Australia so kind of similar climate to yours its very hot here, I’m assuming its best to use an AIO.
@KleoYan
6 ай бұрын
@@fisnikhoxha3114 yup. Get a 360 liquid aio. I do know 240 is capable to cool your 5600x but for the aesthetic. 360 looks nicer.
@fisnikhoxha3114
6 ай бұрын
@@KleoYan I’m thinking of purchasing the Deepcool LT720 the 360 version, do you think that is a quality aio? I’m also worried that it would shorten the lifespan of it as i want to leak over more towards aesthetics and mount it on the right hand side and not on the rear. So far my build is this case and the 5600x, msi mag b550 tomohawk wifi, 32 gb of ram at 3600 mhz 2tb ssd and an rm850x corsair gpu. My graphics card is an xfx qick309 speedster 16gb
@KleoYan
6 ай бұрын
@@fisnikhoxha3114 LT720 is a good liquid AIO, it will do it's job, only think I dislike are the fans which is kind of noisy after 1800rpm. Nevertheless you don't really need to worry about the quality of LT720.
@salvadoralberti1372
5 ай бұрын
Sorry! Kleo
@KleoYan
5 ай бұрын
Hi Salvador Alberti, welcome to my channel. Hmm, why sorry, did I mention anything incorrectly? hmm. 🤔
@salvadoralberti1372
5 ай бұрын
@@KleoYan not at all, it was my writing editor who called you Kelo, hahaha.
@KleoYan
5 ай бұрын
@@salvadoralberti1372 oh ok ok .. no worries about it.. thank you for the clarification 👍
Пікірлер: 281