Excellent vid, the only video that took the damn time to go at the ARGB and actually play with it. EVERY other review didn't do what this case was for which is the ARGB strips. Well done bro.
@KleoYan
Ай бұрын
Hi Kaminosami, welcome to my channel and thank you for your valueable feedback, greatly appreciated it 😉
@F-Bomb313
9 ай бұрын
very nice review, we care about all these depths and measurements, most channels don't give you this information, thanks for the vids
@KleoYan
9 ай бұрын
F-Bomb, welcome to my channel. Thank you for your kind words, greatly appreciated it. Just for your info. I am a pc builder not a reviewer. So most of the time is either I go guides on ARGB stuff or to talk about a pc product value and not just some marketing gimmick. Again, thank you for your valuable feedback. I will continue to bring in better content 😉 Merry Christmas too 😬
@ArjuuuN-FC
7 ай бұрын
My man! your review is on point with all those measurements. We can clearly see the hard and detailed work you put in this. Much Success to you!
@KleoYan
7 ай бұрын
Hi ArjuN. , welcome to my channel and thank you for your valuable feedback, greatly appreciated it. All the best with your build too 😉
@sirlouie
2 ай бұрын
What an incredibly thorough review. Thank you!
@KleoYan
2 ай бұрын
Hi sirlouie, welcome to my channel and thank you for your valueable feedback. All the best with your build too. 😉
@ML_EU
7 ай бұрын
It's the second case review I've watched on your channel... Dude! You're more than video-user-manual! The way you tear everything down is just a competition smashing! Please never get bored and always do such a deep content. Lovely!
@KleoYan
7 ай бұрын
Hi Marcin, welcome back. Thank you for your valuable feedback. I will continue to do what I can 😉 thank you again.👍👍👍
@krazykh
8 ай бұрын
Such clear and detailed instructions. Thank you for all your hard work
@KleoYan
8 ай бұрын
Hi krazy_kh, welcome to my channel and thank you for your valuable feedback 😉
@mashi9693
6 ай бұрын
You’re a life saver, I went with the o11 evo and arctic 360 iii after your reviews. Thanks a lot for making the hardest parts simple.
@KleoYan
6 ай бұрын
HI Mashi, welcome to my channel, my pleasure and glad to of help. All the best with your build too. 😉
9 ай бұрын
Thank you for the review
@KleoYan
9 ай бұрын
Hi Kevin Žiher, welcome to my channel and thank you for your valuable feedback. Greatly appreciated it. as for setting up, I am waiting for some parts, am going to do a theme build on this case.. will take sometime. All the best with your build too.
@Paco15151
2 ай бұрын
Great job man ! Rare to find such complete tour of a case !
@KleoYan
2 ай бұрын
@@Paco15151 hi welcome to my channel. I am glad you like the content and thank you for your feedback 👍👍👍
@mizy7499
5 ай бұрын
Thank you for the review just bought and building in it soon😊
@KleoYan
5 ай бұрын
Hi Mizy, welcome to my channel. I am glad you like this content and thank you for your feedback. All the best with your build too 😉
@GreenEggsAndGraham
9 ай бұрын
I feel bad for not finding and subscribing to this channel sooner.. Great content.. Thank you for your work!
@KleoYan
9 ай бұрын
Hi GreenEggsAndGraham, welcome back. Thank you for your kind words, greatly appreciated it.. Merry Christmas too 😉
@briantaylor3031
2 ай бұрын
Just dropping a line to say i appreciated your detailed video overview, this helped me immensely in picking this case and the Arctic liquid freeze II 420. Case was an absolute dream to build in, i did opt to not power the rgb
@KleoYan
2 ай бұрын
@@briantaylor3031 hi and welcome to my channel. I am glad this content did aid you. Thank you for your comment and all the best with your build too 😉
@kevinh5024
5 ай бұрын
Excellent, detailed video. Im going to but this case and do a new build. You eliminated some questions that I had. Thank You!
@KleoYan
5 ай бұрын
Hi Kevin H, welcome to my channel and am glad to of help. All the best with your build too 😉
@kevinh5024
5 ай бұрын
Subbed too!!
@KleoYan
5 ай бұрын
@@kevinh5024thank you 😊
@jam2944
2 ай бұрын
Man what a good case review video seriously. Just what i needed to figure the 420mm bracket for my freezer aio and i just ended up watching the whole video.
@KleoYan
2 ай бұрын
Hi Jam, welcome to my channel. I am glad you find this content useful. All the best with your build too. 😉
@raffyagista5090
17 күн бұрын
your review are helping me a lot, thank you brother.
@KleoYan
17 күн бұрын
Hi Raffy Agista, welcome to my channel. I am glad to of help. All the best with your build too. 😉
@Heartkiller1991
5 ай бұрын
Sweet JESUS this review was insanely good. Subscribed. Keep it up :)
@Heartkiller1991
5 ай бұрын
Do you have any videos that showcase the RGB with that tinted glass however? I'm a bit worried the tinted glass is going to end up hiding a lot of the beauty inside of the case.
@KleoYan
5 ай бұрын
@@Heartkiller1991 hi, welcomd to my channel. Do pardon me, nope but you don't really have to worry about the tint, so long your internal have ARGB, it will shine out.
@KleoYan
5 ай бұрын
@@Heartkiller1991 hi welcome to my channel and thank you for your feedback. Do pardon me, nope, I do not have that but rest assure if you have RGB internally, your parts will shine through.
@wadehanson7023
5 ай бұрын
Amazing video Kleo!! So comprehensive and informative. Sealed the deal on me choosing this case. Thank you for your hard work on this!
@KleoYan
5 ай бұрын
Hi Wade Hanson, welcome to my channel and it's my pleasure. All the best with your build too 😉
@yohanes2034
9 ай бұрын
Thanks for showing the 420 radiator setup on top as I have that in mind. I’m excited that the case allow for 140x3 setup fans on side and bottom as well but seeing how low the 420 radiator (due to the hanging mechanism) I bet it will block at least half of the top 140 mm fans on the side. I guess I’ll stick with 3x120 on the side, 3x140 on the bottom, and as mentioned 420 radiator on top. Appreciate you went into details with everything else, it would help me once I decide to upgrade next year
@KleoYan
9 ай бұрын
Hi John1K, welcome to my channel and I am glad to of help 😉 All the best with your build too.
@skkl8045
7 ай бұрын
No it's doesn't fit, i tried now, it only allows 3 140mm on top or bottom but side is smaller.
@KleoYan
7 ай бұрын
@@skkl8045 Afrer checking you are partically right. if using uni fans, no issue even though missing two slot to hold the fan at the top from the side. If just normal fans, that will not be secure enough. Thank you for your feedback.
@coastercub71
6 ай бұрын
So I have this case and wanted the article freezer iii 420mm on the top. In the motherboard low position it should fit. Can you confirm that ?
@KleoYan
6 ай бұрын
@@coastercub71 hi welcome to my channel yes, you can watch timestamp 20:52 it will show you the Arctic LF2 420 at the top and motherboard at low mode.
@justinskrub3722
8 ай бұрын
dude you are doing a great job thank you for explaining everything
@KleoYan
8 ай бұрын
Hi Justin Skrub, welcome to my channel. I am glad you like my content and thank you for your valuable feedback. All the best with your build too😉
@vladNMP
8 ай бұрын
keep doing these! arctic should really sponsor you
@KleoYan
8 ай бұрын
Hi vlad NMP, welcome back, thank you for the feedback and yes, Arctic is sponsoring me 😉
@CharlieToof
6 ай бұрын
I like the gloves without the fingers, best way to leave marks with style, btw nice video!
@KleoYan
6 ай бұрын
hello CharlieToof, welcome to my channel. Thank you for your feedback and do pardon me if I my fingers disguest you.
@CharlieToof
6 ай бұрын
@@KleoYan nope i love them, but i dont get the point
@KleoYan
6 ай бұрын
@@CharlieToof oh ok. I don’t usually wear gloves. Just that I got a deep cut and it’s gross when it was not healed.. If you watch this kzitem.info/news/bejne/lnxn1n6ohGZ7fJg You will see my scare on my right hand. That’s why I wear gloves.
@CharlieToof
6 ай бұрын
@@KleoYan now i get the point :) btw scars are sexy
@KleoYan
6 ай бұрын
@@CharlieToof hahaha. Well accident do happened so ya, got to leave with it 😉
@AdrianPragacha
8 ай бұрын
Thank you so much for the in depth review of this case. I have a arctic LF 420 aio and the number of cases with support for this aio is very limited. Glad to know that this case can fit it.
@KleoYan
8 ай бұрын
Hi HAIDZ, welcome to my channel, am glad this content did aid you. All the best with your build too.
@varshithjackson
2 ай бұрын
Amazing video. was searching for a Top 420mm radiator compatibility and found a very detailed installation process too. kudos for this vid
@KleoYan
2 ай бұрын
Hi FaceLess_24, welcome to my channel. Thank you for your kind words and I am glad you found what you needed. All the best with your build too.😉
@ingemarzarate7971
9 ай бұрын
ive been waiting for this bro, thanks
@KleoYan
9 ай бұрын
Hi Ingemar Zarate, welcome to my channel and am curious, hope you don't mind.. what are you exactly waiting.. reason I asked is for personal improvement, if it's related to my style of content I will want to improve further.. By the way, thank you for your feedback and all the best with your build too.
@teralogin1
9 ай бұрын
I'm not surprised that I have found the best review on KZitem right on this channel :o Keep going Kleo Yan, Thank You for actually showing us how it works! You are the best!
@KleoYan
9 ай бұрын
Hi Боремся против Барби, welcome back... thank you for your kind words, I will continue to do better content in furture. Thank you again for your kind words and Merry Christmas to your family and you too 😉
@sivanyc
7 ай бұрын
Your video answered all my questions and helped me decide on buying this case! Thank you for the awesome review!🙂
@KleoYan
7 ай бұрын
Hi ShibaNYC, welcome to my channel and I am glad this content did aid you. Thank you for your feedback and all the very best with your build 😉
@jedemmalter9484
7 ай бұрын
This is amazing video! Thanks a lot for it, for Your effort and all details provided. (in last moment, I changed my mind and ordered this one instead of Vision model)
@KleoYan
7 ай бұрын
Hi Jedem Malter, welcome to my channel and I am glad you like my content. To be honest, I prefer this EVO RGB more than the Vision. 1) For thermal reasons as I am base in a hot and humid country, 2) The asthetic is as good and maybe even better compared to vision. Vision you need to be good with cable management as everything is expose, especially the white version of the case.
@AM-hm5eq
2 ай бұрын
I own this case and it accepts the Artic III 420. It takes a little work, meaning cable connection to MB. Of course Motherboard dependent. I have a Gigabyte DDR4 690. I love the case.
@KleoYan
2 ай бұрын
Hi A M, welcome to my channel, good to hear that you like your setup and thank you for sharing 👍👍👍
@AbhishekPatel-xf1ot
8 ай бұрын
hi kleo yan, superb review and detailing, i am sure your chanel will grow big. i am confused between vision and evo rgb just because of rgb strip. i want asthetic and my buiild is simple i7 and intel arc A 380 just for multiple monitor output few 4k, though i live in very hot climate.but i got my answer through comments , you addressed them all profoundly which is impressive.still a demand if possible kindly make a short video on comparision of both cases.
@KleoYan
8 ай бұрын
Hi Abhishek Patel, welcome back. I wish I can do a short video about it but the 011 Vision is no longer with me. I believe you wanted to know the thermal on both chassis. This is for the O11 Vision in a room temperature of 30°C ~ 31°C kzitem.info/news/bejne/2Gunnql4iWepf6w . As for the O11D EVO RGB, that will be in an content which I will be doing this weekend. To be honest, in a hot and humid contry, it will be best to use the O11D EVO RGB than to the O11 Vision. In general, for a hot and humid country, the air that is being drawn inside the case, it's warm air unlike in cooler countries where the air drawn inside to the case is cool. therefore the O11D EVO RGB has the advantage in thermal over the O11 Vision.
@Canis_Majoris_PR
6 ай бұрын
Спасибо за подробный обзор. Очень приятно смотреть ролики в вашем исполнении. По тому что можно улучшить: 1) Не рассмотрели низ корпуса, насколько я знаю там есть воздушный фильтр и возможность переместить USB\AUDIO хаб в положение с боку а не спереди. 2) Местами в видео видны эффекты "шума" предполагаю что это возможно из-за недостатка освещения. Спасибо за обзор. Thanks for the detailed review. It’s very nice to watch videos performed by you. What can be improved: 1) We didn’t look at the bottom of the case, as far as I know there is an air filter and the ability to move the USB\AUDIO hub to the side and not the front. 2) In some places (7:47), “noise” effects are visible in the video; I assume that this is possible due to lack of lighting. Thanks for the review. *Automatic translation
@KleoYan
6 ай бұрын
Hi Тёма, welcome to my channel, thank you for the feedback, I will take note on the lightening which caused the noise.
@elkiq95
Ай бұрын
Great video explaining the case in such detail.
@KleoYan
Ай бұрын
@@elkiq95 hi welcome to my channel. Thank you and all the very best with your build 😉
@Henrique-wv9xq
7 ай бұрын
Hey, man! Great review! Just a quick question, when using the Liquid Freezer 420mm, you showed how it looks with the motherboard in "low mode". My question is if, when using the motherboard in "high mode" with this AIO, the power connectors for CPU become hard to reach or the space becomes too tight and hard to plug it in? Thanks
@KleoYan
7 ай бұрын
Hi Henrique, welcome to my channel. If you place the motherboard at High mode, the area where you place the EPS cable, it will be tight and you will need to use flat modular cables and not sleeve cables.
@Henrique-wv9xq
7 ай бұрын
@@KleoYan Great, thanks for the info!
@KleoYan
7 ай бұрын
@@Henrique-wv9xq You are most welcome. All the best with your build but if high mode does not work, you have to be prepare to use low mode.
@CyberTweaker
9 ай бұрын
Thank you , you answered all my questions And more
@KleoYan
9 ай бұрын
Hi Lionel Auguste, welcome to my channel and am glad of help. All the best with your build too. 😉
@IronManPeter
8 ай бұрын
Really nice and in depth review ! Well done 😎 In Fractal Define 7 XL and Meshify 2 XL the Arctic LF II 420 AIO also will fit ;) I had both , but I have moved to Evo XL some weeks ago 😊
@KleoYan
8 ай бұрын
Hi Peter Parker, welcome to my channel and thank you for your valuable feedback. Evo XL is even better, you can mount 3 x 420 radiator for custom water loop. nevertheless am glad you found something which you like. 😊
@IronManPeter
8 ай бұрын
@@KleoYan you are totally right :) but after I saw this Evo RGB and due to it has smaller footprint and this fancy RGB stripes, I will sell my Evo XL and switch to it 😁 sounds crazy , but I love to built 😂😍 Keep your good work up and all the best for 2024 😎
@KleoYan
8 ай бұрын
@@IronManPeter @.@ you serious, aik! but ya EVO RGB does have a smaller foot print. I do like this case but I wish the motherboard tray is removable. Thank you for your blessings and all the best to you too for 2024 😉
@IronManPeter
8 ай бұрын
@@KleoYan many thanks Kleo!
@KleoYan
8 ай бұрын
@@IronManPeter you are most welcome 😉
@elefunk13
9 ай бұрын
Hello from Greece. 2 days ago I ordered Lian li Vision from Germany but I immediately canceled it cause I'll wait for this one. I think it will take about a month.. Cheers
@KleoYan
9 ай бұрын
Hi ya, welcome to my channel and thank you for sharing your updates. I am glad you have choosen the case you wanted. All the best with your build and Merry Christmas 😉
@TheWhale030
7 ай бұрын
best video for this tower if seen! congrats man!
@KleoYan
7 ай бұрын
hi Mark Welle, welcome to my channel and thank you for your feedback, greatly appreciated it. All the best with your build too. 😉
@Exomicxx
6 ай бұрын
I really like the video, u explain everything and u explain so good, it’s awesome ! 😊
@KleoYan
6 ай бұрын
Hi Électrocat, welcome to my channel and thank you for the compliment, greatly appreciate it. I am glad you like my content. 😊
@cactuarking4138
6 ай бұрын
Looks like a great case! I was considering the XL then I realized this guy existed for the same price of the regular evo 😅
@KleoYan
6 ай бұрын
Hi Cactuar King, welcome to my channel. Thank you for your feedback and all the best with your build too. 😉
@batuhandurmaz6872
3 ай бұрын
Thank you! I think your video guide will help me a lot to build my system in this case.
@KleoYan
3 ай бұрын
Hi Batuhan Durmaz, welcome to my channel and thank you for your feedback. I am glad to of help. Maybe let us know how it turns out when you have completed your build. All the very best too 😉
@batuhandurmaz6872
3 ай бұрын
@@KleoYanyo right now I am building I also bought 420mm Artic III but the brackets send me is strange different from yours, trying to figure out
@batuhandurmaz6872
3 ай бұрын
I will try to screw to rad plate directly lets see
@KleoYan
3 ай бұрын
@@batuhandurmaz6872 Hmm.. maybe take some pics of your O11D EVO RGB brackets at the top to my email godzylatech@gmail.com . I see what I can find out, thanks!
@batuhandurmaz6872
3 ай бұрын
@@KleoYan I sent
@vladNMP
8 ай бұрын
hey man, would you be able to do a review of ASUS Prime AP201 compatibility with arctic 280/360 rads? it's a really interesting budget mini itx case which would be amazing to be put together with an arctic aio. thanks!
@KleoYan
8 ай бұрын
Hi vlad NMP, welcome back, for Asus AP201. You can only place a 240 Arctic LF2, you can’t do 280 or 360. There are not enough clearance. kzitem.info/news/bejne/0WOa33ubnaeIn6w
@paul2609
5 ай бұрын
I wish they'll do a grey version of this
@KleoYan
5 ай бұрын
Hi Paul, welcome to my channel. Same thoughts but I wanted gun metal 😬. Anyway will feedback your comments to Lian Li. Hopefully in future, they will have more color options.
@Tomasis007
8 ай бұрын
Hi, thank you for the review and for showing how the case and its RGB look in the dark. Can I ask you if the tint is the same as on the black versions of O11 Vision and O11 Dynamic Evo? Because I really like the one on Dynamic Evo and I honestly wouldn't mind even darker. Thanks again
@KleoYan
8 ай бұрын
Hi Tomáš Tvrz, welcome to my channel. As compared, both are tinted the same shades.
@AMMO_x
9 ай бұрын
Awesome video! Can you maybe make a short video about every RGB cycle and modes/colors available?
@KleoYan
9 ай бұрын
Hi Hany_20vt, I see what I can do as currently out of town, can't really do a short video right now. Thank you for the suggestion and Merry Christmas 😉
@Nico-ub1pv
9 ай бұрын
What a nice case! 😮
@KleoYan
9 ай бұрын
Hi Ya buddy, welcome back. you will soon to have, not to worry 🤣
@OMGmiTex
4 ай бұрын
Hi man thanks for this great video, do you plan to make a new one about thermal solutions like you did for O11 vision ? Or the fans placement is similar to the old O11 dynamic evo ?
@KleoYan
4 ай бұрын
Hi Tiiqo FS , welcome to my channel. For the thermal. it's of the same configuration which I did for O11D EVO. It's of the same structure kzitem.info/news/bejne/wqKw0Jeurn1kqqAsi=Bptve9U_ityDOz6_
@sebastianwilczynski7696
19 күн бұрын
Great review, thank you
@KleoYan
19 күн бұрын
Hi Sebastian Wilczyński, welcome to my channel and thank you for your valuable feedback. Greatly appreciated it and all the very best with your build too 😉
@ASHSTORMs
9 ай бұрын
Perfect review! Thanks
@KleoYan
9 ай бұрын
Hi ASHSTORM, welcome to my channel and thank you for your feedback, greatly appreciated it.😉
@krzysmis2366
Ай бұрын
Hi, nice video but to put into perspective motherboard high position is problematic (not imposible but painful!) look at how much clearence you got for motherboard power it will be super close to fans and now imagine trying to squize power cables to for motherboard not going outside the case?) can you make video of how to go up? I got 3x140 arctic freezer option where the show installed freezer as you show - on brackets - but just by size comparition I see it could be possible to move it and isntal without the brackets - I mean I see that size of this would allow moving it up and also the front case and radiator screws are aligned perfectly... the only problem would be case fold on back which takes around 8-9mm case leangth - making it not be able to move up but the fold is in around 6mm-7mm so taht means we would be able to move the freezer 2whole cm up without the special bracket. But of course problem with is that you would need long screws and spacers (something that will be on screw between case and radiator - possible generation of vibrations and sound. .. I wonder why the bracket is so damn big - there is 2cm of possible clearance) are you able to show instalation on high position if its even possible ?
@KleoYan
Ай бұрын
Hi Krzys Mis, welcome to my channel and thank you to have taken your time to write out this feedback. however I no longer have this case, therefore unable to do up a video. Nevertheless you are right about the gap for the 8pin EPS connector. As I recall, it did have issues mounting a 420 Liquid AIO at the top with motherboard at high mode and unable to plug the 8Pin EPS connector as it was sleeved, but by using flat 8pin EPS cable like the FSP Hydro PTM PRO ATX3.0(PCIe5.0) 1200W, I am able to but with a bit of struggle as the gap it's too tight.
@frank_soares
9 ай бұрын
I love the look of this Lian Li, but I can't buy it, I wanted a thin LED strip to put on the sides of my old Dynamic 011 to look identical, is this modification possible?
@KleoYan
9 ай бұрын
Hi Frank Soares, welcome back. I can only suggest you to do the strips underneath your O11 Dynamic. as for modding to be like this EVO RGB. It will be tricky, need alot of perfect alignment and you need a frame to hold the argb stips. Also the part where how are you going to get small or flat strips?
@smugbiz
8 ай бұрын
very nice video, i like the black version of this case but i have white hardware. do you also feel that the white versione feels too empty without 140 fans? it somehow looks more outdated than the OG evo to me
@KleoYan
8 ай бұрын
Hi Yvan, welcome to my channel. This is my opnion, in my eyes, I prefer black over white. black looks sleek and is an optical illusion that the case looks smaller. As for white, yes it does look empty and dated. If you have white parts, you can always do contrast build, as in make and match both white and black in the black EVO RGB. It will look as good.
@smugbiz
8 ай бұрын
@@KleoYan yeah even with 140mm fans the white EVO RGB looks weird to me, Vision looks alright as it’s more compact and doesn’t have as big empty space. Your video demonstrating temps really swayed me away from that case as in the summer we hit 37C … i still will be rocking my OG white evo for some time then haha. it’s 2 years old now but i feel like the design of it is timeless compared to these fish tank models. my only gripe with it is the lack of space for cables. I’d like to do a black build when upgrading the platform (so around rtx 5000 launch). keep on pushing informative content!
@KleoYan
8 ай бұрын
@@smugbiz hi I totally understand your point of view. I mean if your current case is working fine. Enjoy it, no point kept changing cases. You will become addicted at sometime. I was once like this. New cases were given to me and I kept changing. Don’t really have time to really use my pc fully. The images and function of each cases hunted me till I gave up. I ran my main rig on an open bench lols. 🤣 btw thank you to have visited, to share your experiences and feedback. Greatly appreciated it and yes I will try to do my best to pump good content. 😉
@ronin1754
6 ай бұрын
Thank you sir ,easy subscribe for you,this video answers all my questions towards this grat case !!
@KleoYan
6 ай бұрын
Hi Ronin, welcome to my channel and I am glad this aid you. All the best with your build too. 😉
@ronin1754
6 ай бұрын
@KleoYan Thank you sir ! Loved the video, my case will arrive in 2 weeks ,i can't wait to start building in it ,and my biggest concern was exactly that 420mm aio as I will go with arctic, been watching the liqiud freezer 3 420mm ,now i can relax and order it as well to prepare for when my case arrives:) All the best to you and keep up the great work you do for all of us !
@KleoYan
6 ай бұрын
@@ronin1754nice. Yup the measurements of the LF2 and LF3 are exactly the same. No issue to fit in this case 😉
@Paul-if1jq
9 ай бұрын
Do you know if the V2 Galahad supports the new TL fans? Which Hub would I use, the original or TL one?
@KleoYan
9 ай бұрын
Hi Paul, welcome to my channel. If you are in general, all uni fans AL SL SL-INF will have to use it's own Uni Controller / Hub. Same apply to the TL which will need it's own TL Uni Controller/Hub. The only thing with allows you to use on the same controller are the TL and TL LCD. Just a reminder, do not mix daisy chain TL fans with the TL LCD, make sure daisy chain of the same set, TL to TL and TL LCD to TL LCD.
@Galaxutube
9 ай бұрын
You did not mention it is missing a dust filter. What is your opinion that it is missing a dust filter on the back?
@KleoYan
9 ай бұрын
Hi Steven R, welcome to my channel. Yup I notice, I miss that out.. infact there is only one dust filter which is at the bottom and thats all.
@Galaxutube
9 ай бұрын
Do they generally not get so dusty with just a fine mesh?
@KleoYan
9 ай бұрын
@@Galaxutube you can always DIY a mesh with magnet strips or you can choose to dust off your case with a soft brush every week, which I normally do.
@Galaxutube
9 ай бұрын
@KleoYan Thank you for the explanation!
@KleoYan
9 ай бұрын
@@Galaxutube you are most welcome.
@ItWasBrilliant
3 ай бұрын
Does Lian li 011 Dynamic Evo RGB (Black case) have tinted or clear glasses? I saw both of them on that case
@KleoYan
3 ай бұрын
Hi I'mBrilliant, welcome to my channel. It's tinted for me. You might want to check at Lian Li reddit forum. www.reddit.com/r/lianli/
@Ihor_Kot
8 ай бұрын
It’s a pity that they abandoned the Lian Li Top I/O-Panel Kit for O11 Dynamic EVO
@KleoYan
8 ай бұрын
Hi Игорь Кот, welcome to my channel, I do understand to have flexibility. Maybe you can voice it out at Lian Li's reddit forum. www.reddit.com/r/lianli/ . On my end I will send a feedback to them directly. Once again thank you for your valuable feedback.
@Armandocav1
9 ай бұрын
Hey Kleo I trust your work a lot, that's why I want your opinion, is it worth changing the old O11 D with this new O11 RGB? I know it's difficult to improve something that's already perfect, that's why I only notice small improvements, but is it worth it in your opinion (my O11D is only one year old) Thank you
@KleoYan
9 ай бұрын
Hi Armando Cavallaccio, welcome to my channel. As a PC Builder standpoint. If your hardware are all very highend products and if you are in a hot and humid country, it is worth replacing but if your temperature are fine with the O11D, you don't have to waste on a case, you can upgrade other PC Components like rams or even m.2 SSDs and such.. This will be my very honest opinion. Alternatively, if you really like the O11D EVO RGB, you can change it and sell your O11D to absord the cost, but are you ready to spend even more on upgrading? as in spend on 140mm fans and 420 Liqiud aio,. There will be more signification improvement this way instead of using all 120mm fans and 360 liquid AIO. The factor of 1) Noise 2) better temperature and 3) to yield better performance. So something which you have to consider, there will be no point changing if you do not change the case setup (as in fans and liquid aio)
@Galaxutube
9 ай бұрын
What case would you recommend to put Arctic Liquid Cooler 2 360 or 420 on top without removing front fans? Is there any midtower that can do it? Or just have to go with Full Tower?
@KleoYan
9 ай бұрын
Hi Steven R, welcome back, it depends greatly on which processor are you using and do you really need a 420? as for 420, they are mainly full tower. So far I only know this case can handle it and this is a mid tower.
@Galaxutube
9 ай бұрын
Thank you. Yes maybe 360 will be enough for Ryzen 9 7860x
@KleoYan
9 ай бұрын
@@Galaxutube hmm there is not such processor as 7860X
@Galaxutube
9 ай бұрын
@KleoYan it is 7950x, was a typo. 360 aio is plenty?
@KleoYan
9 ай бұрын
@@Galaxutube I see. I would either use a 280 and 420 from arctic. If you are running by default. But if you do PBO2 and undervolting, 360 is sufficient.
@bobchicken9056
5 ай бұрын
Can i install an 420mm radiator with 3x140mm fans on the top and 3x140mm fans on side along with 3x140mm fans on the bottom simultaneously
@KleoYan
5 ай бұрын
Hi Bob Chicken, welcome to my channel. Yes you can place the fans and liquid AIO the way you’ve mentioned. But do note for the side, you do have space and you can mount 3 x 140mm fans but with only 10 screws and not 12.
@WyattYork-x7c
5 ай бұрын
Great video - I'm particularly interested in a 420 mm AIO - are the two brackets for 420 mm included with the case??
@KleoYan
5 ай бұрын
Hi Wyatt York, welcome to my channel. Yes these brackets are included when you purchase this case.
@fastdrifts1665
9 ай бұрын
So do you think this case can fit a 4090 and a 420 aio
@KleoYan
9 ай бұрын
Hi fast drift, welcome to my channel. Yes it can fit without an issue. You have enough clearance.
@fredrei12345
6 ай бұрын
Thanks for such a detailed review of the case, this is extremely helpful for people planning out their builds. I'm looking to move my current MATX build into this case and upgrade to an ATX Motherboard early next year. For the MATX Mobo, there would be empty space underneath the GPU. To avoid excessive cables in that empty space I plan to route cables from the side rather than bottom so most of them will be hidden underneath the GPU. I haven't been able to find anyone who tried MATX in this case. Is there anything I should be mindful about putting an MATX motherboard in this case?
@KleoYan
6 ай бұрын
Hi Fred Sun, welcome to my channel, thank you for your feedback. If you are to place a M-ATX board, 1) on the upper mode position. the bottom section will be very bear and as what you have mentioned to tug the cables at the side. This will not be an issue if you mount your GPU vertically. 2) on the lower position mode, this will be worst. both top and bottom, the space is alot, even if you place a GPU vertically mounted. the top will be very bare. For temporary solution before you get a ATX motherboard, just bear with the looks, but if it bothers you, I will go with option 1)
@fredrei12345
6 ай бұрын
@@KleoYan Thanks for your fast reply. If I'm trying to fit an Arctic Freezer 420 AIO on top and 3x 140mm Uni-TL Fan at bottom with an ATX motherboard (similar to your video), which motherboard position would you recommend? In the video the upper mode position looked really tight with the 420 AIO. Would there be enough room to run CPU Power Cable through? I also heard about clearance issues for bottom cables in the lower position mode when using 140mm TL Fans (they are 28mm thick).
@KleoYan
6 ай бұрын
@@fredrei12345 for me I will do ATX in low mode in this case and if you have a look at the bottom. There are rubber grommets below the ATX board placement. There will still be sufficient space for you to put 140mm fans plus you are using TL 140mm, minimum cables are required to hide at the side. You are right about the front I/o cables and such. What you will have to consider is only the audio cable. As that’s the only thick cable you need to worry about or if your front I/O 3.2 connector is not at the front of the motherboard but below, then you going to have an issue.
@skkl8045
7 ай бұрын
After seeing your video i bought it, it doesn't fit. x3 140mm fans won't fit on the side, only bottom or top.
@KleoYan
7 ай бұрын
Hi Skkl, welcome to my channel. Afrer checking you are partically right. if using uni fans, no issue even though missing two slot to hold the fan at the top from the side. If just normal fans, that will not be secure enough. Thank you for your feedback.
@skkl8045
7 ай бұрын
Thanx for answering very fast, im going to subscribe. I have a question, what should i do with the (rgb) Sata cable coming out of the case, i have "be quiet straight power 1500w" PSU but it doesn't have this type of port. Where should i plug the cable or what should i do.
@KleoYan
7 ай бұрын
@@skkl8045 you should connect the sata cable to your PSU sata connector. your power supply should come with modular sata cables which allows you to plug to the section that says Drives, then at the other end of the modular sata cable, plug it to the case sata connector
@richvspoor2652
9 ай бұрын
You didnt show the INSDE RGB, how dark the glass is -.- oh god...when review the case show also how it looks with RGB FANS inside...
@KleoYan
9 ай бұрын
Hi Rich vs Poor, welcome back. fully understood, you might want to tone down and at least with a greet. You don't have to repeat your demands as I do not owe you anything. Thank you!
@RollingTaro
9 ай бұрын
Can the case rgb connect to the lian li uni fan controller?
@KleoYan
9 ай бұрын
Hi Shiitaro, welcome to my channel. Yes you can, but you need an adaptor. you will also need to set to motherboard mode on the case switch itself.. make sure the case Sata is at all times plug too as there are two strips.. so the drawning power is directly from the PSU before you plus the argb to the uni fan controller argb sync 1 or sync 2 port.
@RollingTaro
9 ай бұрын
@@KleoYan Thanks for the reply
@KleoYan
9 ай бұрын
@@RollingTaro you are most welcome. All the best with your build too.
@RollingTaro
8 ай бұрын
@@KleoYanhey again, do you have a link to where I could find the adapter?
@flaccus123
6 ай бұрын
Amazing video on the Evo RGB. Best I have seen. I assume no issues fitting the new Freezer III 420 in top ? At 22:05 where you are showing the Freezer II 420 it looks like the fans are blocking the PSU EPS cable grommet. Can you offset the AIO outwards so you can route the cables. This was a major problem on the Corsair 5000D with almost any 360mm AIO. Thanks.
@KleoYan
6 ай бұрын
Hi Keith Flanagan, welcome to my channel. Both LF2 and LF3 420 are of the same size and measurement. No issue to mount. All the best with your build too 😉
@flaccus123
6 ай бұрын
@KleoYan Thanks and no issue with routing braided PSU cables through the top grommet ?
@KleoYan
6 ай бұрын
@@flaccus123 nope for me I am always use non sleeve cables (flat) If you rewatch my content. It will shows you that the 2 x eps 8pin socket has plenty of space. Just make sure your motherboard is place at low mode. If you use sleeve cables. There might be some struggle.
@opfreakx
8 ай бұрын
Would you know why a 420 mm raditor would not fit on the side? Lian Li says only top and bottom, but you might be able to measure or do a fitment.
@KleoYan
8 ай бұрын
Hi opfreakX, welcome to my channel, I would have shown if it’s possible. There are not enough space to fit a 420 rad and the actual length of the rad is 450mm. As why can’t fit 420 at the side maybe you can send an email to Lian Li or to post your question at their Reddit forum.
@opfreakx
8 ай бұрын
@@KleoYan thank you for the response
@KleoYan
8 ай бұрын
@@opfreakx you are most welcome. If you need 420 at the side. The only case is the O11D EVO XL
@opfreakx
8 ай бұрын
@@KleoYan I was starting my research, and I have my PC on the lefthand side. the O11 line up is one of the few that can be flipped. But inverted the space between a 'top' mount radiator and the graphics card gets tight, which is what I was thinking of going with a side mount. I'm glad I did more research before buying a 420 rad.
@KleoYan
8 ай бұрын
@@opfreakx the EVO XL able to invert.
@scythcopath6186
9 ай бұрын
Hi Kleo Yan, may i know where i purchase this case? I tried looking for it but to no avail. Thanks
@KleoYan
9 ай бұрын
Hi scythco path, the only list I have which most are not availble in stock yet, you can try looking it up from time to time with these link. Black www.newegg.com/p/2AM-000Z-000C0?Item=9SIAFSTK677375 White www.newegg.com/p/2AM-000Z-000C1?Item=9SIAFSTK677379 Caseking caseking.de/o11d-evo-rrgb OCUK www.overclockers.co.uk/lp/lian-li-o11-evo-rgb
@scythcopath6186
9 ай бұрын
Thanks. much apperciated@@KleoYan
@KleoYan
9 ай бұрын
@@scythcopath6186 you are most welcome.
@krazykh
7 ай бұрын
Do the screws needed to install the brackets to the 420mm rad come with the case ? are they the same as the screws used to mount radiators in the case?
@KleoYan
7 ай бұрын
Hi Krazy_KH, welcome to my channel. The screws comes with the case for you to mount the this bracket to the case top.
@francisdumlao8040
4 ай бұрын
I recently transplanted my pc to this case. I got the new arctic liquid freezer 3 420aio installed on low mode. I tried it on high mode but somehow the CPU cables is blocking it. It probably fit if i unplug the cables first but it will be difficult plug it back in. Low mode is the way to go if installing LF3 420.
@KleoYan
4 ай бұрын
Hi Francis Dumlao, welcome to my channel and thank you for sharing your experience, this will aid others too. 👍👍👍
@Antho2030
7 ай бұрын
With the LF420 at the top, is there enough clearance for connecting the CPU power câble ? You didn’t mention it if i’m not wrong… Thx !
@KleoYan
7 ай бұрын
Hi Anthony Arnould, welcome to my channel. At the gap between the 420 LF2 and the motherboard, there are enough space to plug the 8pin EPS cable, so long it's not push pull configuration. have a look aat timestamp 20:54
@Antho2030
7 ай бұрын
@@KleoYan yes i saw but i wanted to say between the LF420 and the case (the rubber hole) ? Is the LF420 enough receded from the mobo support ?
@KleoYan
7 ай бұрын
@@Antho2030 I see, yes it has a gap of 15mm gap between the hole to the 420 rad.
@Antho2030
7 ай бұрын
@@KleoYan thx a lot !!
@KleoYan
7 ай бұрын
@@Antho2030 You are most welcome.
@wirek69
4 ай бұрын
on official lian li website they mention only 120mm on the rear will fit. you said 140 will fit is there a place for screws for 140 :O?
@KleoYan
4 ай бұрын
Hi wir3k, welcome to my channel, I specifically mentioned the rear is for 120mm fan. at time stamp 06:55
@wirek69
4 ай бұрын
Thanks for your time to do a video and reply to me promptly. Agree my mistake I miss heard you at 21:27. Now I hear you clearly say 120 not 140 All the best!
@KleoYan
4 ай бұрын
@@wirek69 no worries. It’s good to clarify. All the best with your build too 😉
@desiderio4844
8 ай бұрын
Great review Kleo. Hey, will 420mm artic ii fit front side mounted tubes down?
@KleoYan
8 ай бұрын
Hi Desiderio, welcome to my channel. You can only fit it at the top, there are not enough clearance at the side or front. Thank you for your valuable feedback and all the best with your build too. 😉
@TPA_JW
5 ай бұрын
I am mounting a 240 Lian Li CPU cooler at the top and I am still a little confused on if I need to use the mounting brackets or not. Help.
@KleoYan
5 ай бұрын
Hi Jon Wyant, welcome to my channel. If it’s a 240 liquid aio, you do not need the mounting bracket. The mounting bracket is meant for 420 liquid aio.
@TPA_JW
5 ай бұрын
@@KleoYan Awesome, great video! I am printing a 27.75mm mounting bracket so the additional 120mm fan I am installing sits flush (even) with 2 fans that are mounted to the radiator.
@KleoYan
5 ай бұрын
@@TPA_JW I see, but why do you need to print a 27.75 mounting bracket? if you doing push pull confuration with a 240 Liquid AIO, you can just mount it directly at the top tray and to have push and pull configuration.
@ryanchenoweth5673
5 ай бұрын
Is there anyway to mount three 140mm fans under a 360mm top mounted aio? 🤔
@KleoYan
5 ай бұрын
Hi Ryan Chenoweth, welcome to my channel. If you able to find the adaptor for it but I do not advise you to do so as using different sets of fans will cause more turbulence. This might damage your fans.
@ryanchenoweth5673
4 ай бұрын
@@KleoYan Thankyou 🙏 will use 120’s and continue to wait for lian li to release a 420mm aio. Is there room for 2x 120mm fans with modification on the back wall? 🤔
@KleoYan
4 ай бұрын
@@ryanchenoweth5673 nope you can't mount 2 x 120mm fans at the rear.
@Gustavo-tg1wm
4 ай бұрын
hey nice video. I have a question about this case... On the back where it only supports a 120mm fan, would it be possible to add two 120mm fans? I want to add an acrylic reservoir there with dimensions of 120mm x 240 mm... Do you think it will fit there?
@KleoYan
4 ай бұрын
Hi GuHydro, welcome to my channel. I have tried with 2 x 120mm fans, it will not fit. So sorry about that.
@Gustavo-tg1wm
4 ай бұрын
@@KleoYan But are you saying there is a lack of space? or that there is no place to put the screws? If you remove the first PCIe expansion card, you may have 240mm of space...
@KleoYan
4 ай бұрын
@@Gustavo-tg1wm hi ok I get what you mean now. You might be able to put 2 x 120mm fans but will have two screws not able to mount. As for reservoir. I wish I can test this out for you as I no longer have this case. So sorry about this and I can’t commit to tell you if you can fit.
@Gustavo-tg1wm
4 ай бұрын
@@KleoYan Sorry, I'm using a translator and it's difficult to explain my question... in short, it doesn't matter to me about screws. If there is space to fit 240mm then that's great. I will find a way to arrest him
@KleoYan
4 ай бұрын
@@Gustavo-tg1wm ok, all the very best with your build. 👍😉
@Lucas-kx8iw
Ай бұрын
is there a possibility in wich the GPU might be too short in lenght meaning the anti-sag mechanism can't reach it?
@KleoYan
Ай бұрын
@@Lucas-kx8iw hi welcome to my channel. Yes, there are cases whereby the GPU does not reach the anti saq bracket. One of them will be the gigabyte eagle 4070ti super. But short length means lesser weight and pressure so that balance off.
@Lucas-kx8iw
Ай бұрын
@@KleoYan i was thinking in buying a dual vent Asus 4070 super, its lenght Is roughtly 267mm
@KleoYan
Ай бұрын
@@Lucas-kx8iw I see, the anti saq bracket might not be able to reach it. In this case I believe Asus GPU does come with a support bracket or something. The weight of the dual 4070 super is not heavy. You might fun fine without it. But if you do need, you might need to get 3rd party support stand or such.
@EnriqueMartinez28
9 ай бұрын
Is there to much differences in thermals between this one and the vision?
@KleoYan
9 ай бұрын
Hi Enrique Martinez, welcome to my channel. To me yes, great difference as I am staying in a hot and humid country, which my room temperature is always at 30°C ~ 31°C. the EVO RGB will have better temperature as I have tested.
@oTheDucky89o
7 ай бұрын
Not sure if u have the same issue but how to make the front LED strip lighting remembers the mode? It keeps reset when I shuts down the pc and I have to change the mode again..
@KleoYan
7 ай бұрын
Hi Kenny Yap, welcome back. I don't have this issue. Just to check, did you also swtich off your main AC to your PSU. for it to remember. you need the standby power to be on. This is auto by default when you just turn off your PC without turning off your AC outlet or to switch off the PSU switch.
@oTheDucky89o
7 ай бұрын
@@KleoYan no I don't switch off anything.. I just shuts down the pc and let it be.
@KleoYan
7 ай бұрын
@@oTheDucky89o hmm then that’s strange. Which psu are you using?
@oTheDucky89o
7 ай бұрын
@@KleoYan I am using FSP Hydro PTM Pro power supply and MSI motherboard. I tried using the MSI center software but it stills resets =/
@KleoYan
7 ай бұрын
@@oTheDucky89o this is abit weird. I have no issues and have tested the FSP PTM Hydro Pro 1200watts Platinum PCI-E 5.0 atx 3.0 ready. But am using a MSI Mortar b650m and the Asus Rog Maximus z790 hero in this case. Both will stay on my last settings. You might want to check with Lian Li on your issue.
@richvspoor2652
9 ай бұрын
IS this realy the new Lian Li O11D EVO RGB ??? from 21.12.2023? THe glass looks so dark tined, but on the pcitures from the homepage of Lian Li it looks much MORE CLEAR??? so do you have the real one or fake, why its so hardcore dark tinted ?
@KleoYan
9 ай бұрын
Hi Rich vs Poor, welcome to my channel and Merry Christmas. It's due to my lightings. In real, it's not dark, I can see through, do pardon me on my setup. If it's fake it's fake then, thank you for your feedback.
@richvspoor2652
9 ай бұрын
Merry Christmas. No Joke, i have this one in my House and returned it. i had the Lian Li O11D EVO black and Lian Li O11D EVO RGB , they have hardcore dark tinted glasses. I mean, you can see through it, sure but its not like on the homepage from lian li, it looks like normal clear glass like from the white one. Also by other youtuber it looks clear and i thnik in europe they sell dark tinted and in america and other countrys with "little bit tinted" glasses, thats the point and it dissapointed myself @@KleoYan
@KleoYan
9 ай бұрын
@@richvspoor2652 I see, let me check with Lian Li and on your end, you might either send a feedback email through Lian Li's contact lian-li.com/contact-us/ or to list your unsatisfaction at Lian Li reddit forum www.reddit.com/r/lianli/ . I do understand your fustration and disppointent but be mindful. I do not represent Lian Li's products, I experience their products and to share my experiences. In future if you want to comment something to somone you do not know. Kindly be mindful of what you are typing, uncessary statments like "yours is real or fake" or "Oh my god, can you do with argb fans to this case", are these called for? Do I owe you anything? If you want things done, ask nicely. If you treat a person with respect, you will in return gain respect. I am nice to reply and to tell you facts, for some others, they will just blacklist or to block you. Thank you!
@nightshadow76
3 ай бұрын
can you not control the rgb with L Connect?
@KleoYan
3 ай бұрын
Hi G M, welcome to my channel. Infact you don’t need to use L-Connect at all. You can just use the case ARGB switch to cycle the ARGB effects.
@손으로똥싸는사람
7 ай бұрын
hi im korean can i use o11d evo rgo 420 radiator whit 6 fans??? english is so hard 😢😢
@KleoYan
7 ай бұрын
Hi 손으로똥싸는사람, welcome to my channel. No, you will have problems. It will hit your motherboard VRM heatsink or your RAMs.
@vasileiossaloufas2994
7 ай бұрын
The brackets for the 420cm AIO are included in the package right?
@KleoYan
7 ай бұрын
Hi Vasileios Saloufas, welcome back and yes, it's included in this case.
@vasileiossaloufas2994
7 ай бұрын
@@KleoYanThanks for your help, I was between Vision and Evo RGB and because I find Arctic freezer II 420 in discount I finally decided to go with the Evo Rgb case after your feedback, thanks again keep the good work.
@KleoYan
7 ай бұрын
@@vasileiossaloufas2994 good choice and all the best with your build. To be honest, I prefer EVO RGB over Vision 🤣🤣
@hello.im.dashhh
5 ай бұрын
Can we setup 6 140mm fan on AIO ?
@KleoYan
5 ай бұрын
Hi Quang Hiếu Vũ, welcome to my channel. You need to check the clearance of your motherboard side vrm. Even if the motherboard is at low position of this case. By place additional set of 140mm fans, you might hit your motherboard side vrm.
@abdessadakbouazi4338
2 ай бұрын
Can you telling me please where can I get the brackets
@KleoYan
2 ай бұрын
Hi Abdessadak Bouazi, welcome to my channel. If you are referring to the 420 brackets, it comes with the case.
@abdessadakbouazi4338
2 ай бұрын
Lian li o11d evo or comes with the arctic
@KleoYan
2 ай бұрын
@@abdessadakbouazi4338 it’s o11d Evo RGB only.
@abdessadakbouazi4338
2 ай бұрын
Thank you so much ❤
@KleoYan
2 ай бұрын
@@abdessadakbouazi4338 you are most welcome
@spayrex_
5 ай бұрын
Hey mate are you planning on showing us a inverted Evo Rgb with 420mm radiator and all 140mm fans?
@KleoYan
5 ай бұрын
Hi Spayrex, welcome to my channel. Do pardon me, I do not have plans to do that, so sorry about that.
@spayrex_
5 ай бұрын
No problem, still an awsome vid. Do you maybe know if i can still install a 420mm on top if i invert the case? Because i dont seam to find a vid about that and dont know how it is rotated...
@KleoYan
5 ай бұрын
@@spayrex_ after looking at the blueprints, there are not enough space for 420 at the top when you invert the case, reason being, is either you mount the GPU upright possition where it already took the space or even if you do it horizontally, the gab bettween the top (with the bracket) to your GPU front, is not wide enough to fit the 420 at the top.
@spayrex_
5 ай бұрын
@@KleoYan oh no :( i wanted a 140mm build... do you maybe know reversed cases that are as small as possible and still hold 140mm fans?
@KleoYan
5 ай бұрын
@@spayrex_ if for fans at the top, you should not have an issue if your GPU is mounted horizontally or mount the upright bracket at the below section. but it greatly depends on how long your GPU is. In general just 140mm fans, it's possible. I got to apologize that I can't test it as the case no longer with me.
@monkeymanx310
7 ай бұрын
Is thisan updated version cus i just bought an 011 evo and it looks different
@KleoYan
7 ай бұрын
Hi Alberto Mendez, welcome to my channel. This is not an update version but it’s another series if the O11D EVO family.
@monkeymanx310
7 ай бұрын
What series/ model is that becuase i biught the white o11 evo rgb DEW but its different from the one in your video.
@KleoYan
7 ай бұрын
@@monkeymanx310 this is the Lian Li O11D EVO RGB lian-li.com/product/o11d-evo-rgb/
@TheTassMen
6 ай бұрын
Is it possible to set the led colour on the case in one static coloour?
@KleoYan
6 ай бұрын
Hi T.W, welcome to my channel. yes you can do that. you can refer to this official website lian-li.com/product/o11d-evo-rgb/ C: Light Color Button: Switch between 11 colors press 3 seconds to activate Pure Color Mode press 3 seconds again to cancel.
@TheTassMen
6 ай бұрын
@@KleoYanThank you very much
@KleoYan
6 ай бұрын
@@TheTassMen you are most welcome and all the very best with your build too 😉
@lostbutterflies1859
2 ай бұрын
nice videos ❤, may i ask a question? so my side panel is shattered by itself randomly today, do you know what size length and width of the side panel? thanks!
@KleoYan
2 ай бұрын
Hi lostbutterflies1859, welcome to my channel and thank you for your feedback. It measures around 478mm x 442mm x 4mm. I would advise you to contract lian li to get a replacement.
@lostbutterflies1859
2 ай бұрын
@@KleoYan thanks for the information kleo! i'll try to contact them after this 🥰
@KleoYan
2 ай бұрын
@@lostbutterflies1859 you are most welcome. Just incase if you need to contact them lian-li.com/contact-us/
@Stigness23
9 ай бұрын
Undecided between this and the XL lol
@KleoYan
9 ай бұрын
Hi Stigmatta, welcome to my channel. If you are makeing a custom water cooling build, I will go to XL, if you are making use of standard cooling solution, Liquid AIO that is.. I will go for this case. That's my opinion, the choice is up to you and thank you to have visited my channel 😉 These are the reason. for standard Liquid AIO, this O11D EVO RGB is just nice and it will not make your build empty as compared using the EVO XL, that case need serious custom watercooling to make it looks good in the interior.
@marchev1982
9 ай бұрын
i have 7000D and my LF II 420mm at the top sit right perfetct side wiht push pull on the top side ,also i dont like the 120mm only rear fan ,and the psu stick at the back is so bad .i lot of people like me probbaly put the case on the desk and whit the psu cable stick at the back hit the wall already push the case foward can imagine how foward the case need to be so not smash that cable in the wall,also i prefer to have my front with mesh for exelent cooling , Deep Cool Morpheus has everything you ever need from cooling point even in single chamber position ,if you can review this case .verry good review btw ,so informative and well done ,keep up the good work
@KleoYan
9 ай бұрын
Hi ivan marchev, welcome to my channel and Merry Christmas. I got your point, well pointed out 👍👍👍 as for the Deepcool Morhpeus, I am waiting for Deepcool's response, this case will be in place for a content for sure as. I would say maybe after the holidays. Thank you for your valuable feedback 😉
@Henrique-wv9xq
7 ай бұрын
if those milimiters of the psu sticking out the back are enough for your PC to be hitting the wall, then you're doing something wrong.
@KleoYan
7 ай бұрын
@@Henrique-wv9xqwelcome to my channel. Pardon me, I don’t really understand what you mean, care to elaborate. Thank you.
@marchev1982
7 ай бұрын
@@Henrique-wv9xq hi, 7000D its a big case ,and i was saying that it sit on the top of my desk ,and already the legs of the case barely fit on it if i push the case foward more its going to fall from the legs ,so i need to pull the desk far away from the wall ,but thats my problem ,i was just saying that people that have small desk like me and use full tower case like this and also had to deal with power supply stick ot from the back and the cable after all it is not convenient and for me its a bad design ,i dont think ive done something wrong with my build .
@ceuser3555
7 ай бұрын
Do they have a front mesh version without losing the side mount? They need to have one with space for a 420mm arctic liquid freezer with a push pull configuration on any way of mounting it.
@KleoYan
7 ай бұрын
Hi CE User, welcome back, for the front mesh, it's of a separate purchase and this case does not cater for front mount 420 even if you purchase the front mesh frame.
@ceuser3555
7 ай бұрын
@@KleoYan I see, that is why I was skeptical of Lian Li although the case of my working PC is a Lian Li 2. I searched online and many have recommended meshify 2 xl for the 420mm arctic liquid freezer. However this meshify case does not have side mounting capability.
@ceuser3555
6 ай бұрын
@@KleoYan good to know, thanks. As I have said earlier, I come from Lian Li Lancool II mesh. Before I was considering full tower options from Lian Li and others, but most of the people posted that Meshify 2 XL is the best fit for my aio.
@ceuser3555
6 ай бұрын
@@KleoYan that after reading from others that an air cooler is okay for a 7950x3d cpu.
@ДмитрийМанжесов-ж1с
2 ай бұрын
Скажите если ставить переднюю сетку.то влезет ли 430 наверх?@@KleoYan
@phalaxis3573
9 ай бұрын
What's your top 5 picks for cases in 2023?
@KleoYan
9 ай бұрын
Hi Phalaxis, welcome back. for me will be these cases. Cougar Duoface Pro, Montech King 95 Pro and this Lian Li EVO RGB.
@Uncle_Joseph
9 ай бұрын
@@KleoYannot the Vision for innovation?
@KleoYan
9 ай бұрын
@@Uncle_Joseph Hi welcome to my channel, nope, I dont like all glass and especially limitation on Airflow.
@Uncle_Joseph
9 ай бұрын
@@KleoYan Same. That reason made me cancel my preorder. Currently preordering the Evo RGB.
@KleoYan
9 ай бұрын
@@Uncle_JosephI mean there is nothing wrong with vision if you are build a not so demanding or power hunger of a processor and GPU. But ya, same like yourself. I prefect the O11D EVO RGB too 😬
@andrewtimothy9792
4 ай бұрын
Does the top bracke flex when you install a 420mm rad?
@KleoYan
4 ай бұрын
HI Andrew Timothy, welcome to my channel. nope, it does not flex.
@andrewtimothy9792
4 ай бұрын
@@KleoYan that is pretty amazing, considering how thin the bracket looks.
@KleoYan
4 ай бұрын
@@andrewtimothy9792 the reinforcement is via the 420 radiator, once bracket is mounted to it.. the whole structure is form. and when mounting it to the top tray, again another reinforcement.
@andrewtimothy9792
4 ай бұрын
@@KleoYan isnt the rad is screwed into the removable top bracket? That bracket loojs pretty thin. Which is why i was amazed that it doesnt flex undet the weight of a 420 rad and 3x140 fans
@KleoYan
4 ай бұрын
@@andrewtimothy9792 though it is thin. when you screw on the rad to the bracket, that will be the first line of strenghten and when you mount to the tray, it's the second line of strengthen.. if you worry about the middle part.. it's a whole bracket that is horizontally across plus it's screwed to the top. I do understand your concern but rest assure it might look thin, infact not really thin, is 3mm thick. if it's of 2mm then you going to have to worry.
@TheDarkKnight2064
4 ай бұрын
How long do you hold the botton and which one top or bottom of the M or C ? I cant turn my on
@KleoYan
4 ай бұрын
Hi dark_knight, welcome to my channel. Press the B button to turn on. M: Next/Previous Light Mode Button: Press 3 seconds to sync MB, press 3 seconds again to cancel. Go back and forth between lighting effects without needing to circle around the loop. C: Light Color Button: Switch between 11 colors, press 3 seconds to activate Pure Color Mode,press 3 seconds again to cancel. B: Light Brightness Button: Switch between 5 brightness levels-100%, 75%, 50%, 25%,0%.
@TheDarkKnight2064
4 ай бұрын
@KleoYan it doesn't turn on at well boss. The top or bottom button of the M key
@KleoYan
4 ай бұрын
@@TheDarkKnight2064 hi, did you read the whole legend which I've type out? If you did but still do not work. You might want to check your connection. did you plug the Sata connector to your PSU sata cable?
@TheDarkKnight2064
4 ай бұрын
@@KleoYanI believe it is connected to it
@KleoYan
4 ай бұрын
@@TheDarkKnight2064 hmm 🤔 you might want to check with Lian Li support as I have no idea what’s wrong with your unit. Sorry.
@FateEUW
6 ай бұрын
Hello Kleo Yan, sorry to bother you, you have helped me last year with my Build, i wanted to know if you can take a look over this Lian Li EVO RGB > SL INF UNI HUB sync Port 3 FANS > SL INF UNI HUB Port 1 3 FANS > SL INF UNI HUB Port 2 3 FANS > SL INF UNI HUB Port 3 3 + 1 FANS > SL INF UNI HUB Port 4 SL INF UNI HUB with 13 SL INF FANS and EVO RGB Case >> Motherboard 5V ARGB Port 1 Strimer Plus V2 HUB 24Pin Mobo Strimer 12VHPWR 8 Light Guide Strimer Palit RTX 4090 Gamerock OC ARGB Y Splitter >> Motherboard 5V ARGB Port 2 Safe to Connect? I don’t want to Fry my ARGB Ports, I want to Have the ability to Control everything With L Connect 3 or Motherboard Software. Thank you
@KleoYan
6 ай бұрын
Hi Fate, welcome to my channel. Spot on. all uni fans and your case LED will be drawing power from the uni controller. the controller can take up to 16 fans at 10.4A but you only have 13 fans which has a total drawn of 8.45A. therefore your case strip will have 1.95A, it should be enough. and the rest like your strimer plus v2 are drawing power from it's own controller. it will be fine. same apply to your 4090 which also drawing power from the PCI-E slot. so no worries that you will blow any of the motherboard ARGB headers.
@FateEUW
6 ай бұрын
@@KleoYan Nice! Thank you very much for your help and your In Depth Videos!!
@KleoYan
6 ай бұрын
@@FateEUW most welcome.. all the best with your new build too.😉
@vegetarischerdrachenlord901
6 ай бұрын
Can you do me a favor? So, it would help me a lot with my current planning. I ordered the following AIO, Liquid Freezer III 420 A-RGB (White) and would now like to buy the matching fans for this too. so the ARCTIC P14 ARGB. Now I have the option of installing three of them at the bottom and only two on the side and on the back of the case it has to be a small ARCTIC P12 ARGB. My question is, could this be combined in another way, i.e. I buy and install ARCTIC P12 ARGB six times? So, I would like to see what it looks like if you have the case and also the fans in stock. Or have you already tried this? And it really doesn't look good combined? Because that's the question I'm asking myself, whether I really need to buy the more expensive ARCTIC P14 ARGB. Postscript I'm trying to make a completely white configuration, so I also have to buy the white fans, which aren't included in the set either :(
@KleoYan
6 ай бұрын
Hi vegetarischer DrachenLord , welcome back, kindly note that the side though it mentioned it can mount 3 x 140mm fans but if you are not using uni fans, that might be an issue. I would advise you to mount this way. Top - 420 LF3 with 3 x 140mm fans exhaust Side - 3 x 120mm fans intake Bottom - 2 x 140mm fans intake Rear - 1 x 120mm fan reason I suggested this is. the view of your case when you place it on your desk. the most prominient exposual will be your die fans, bottom fans and rear fans. that will gives you a pleasant sight. if you want to do all 140mm. then do this all 140mm without the rear fan. but as mentioned to you, the side fans if you want to place 3 x 140mm fans, one of your fan will have 2 fan holes not able able to screw to the side try.
@vegetarischerdrachenlord901
6 ай бұрын
I have to thank you again. You're great, thank you very much for your always very quick and extremely competent help. I was afraid, maybe it looks not good to combine 140 and 120 in one case. But I trust you! :) I would like to use the MSI X670E Gaming Plus WIFI mainboard. With this wide variety of fans, I may need an additional device such as the Arctic Case Fan Hub, 10x and which fans would you connect to it? I learned from you that these can only be controlled uniformly and no longer individually. The board has the following connections: Internal connections 1x USB-C 3.1 Key-A header (10Gb/s), 2x USB 3.0 header (5Gb/s, 4x USB 3.0), 2x USB 2.0 header (480Mb/s, 4x USB 2.0), 4x SATA 6Gb/ s (X670), 1x TPM header, 1x USB4/Thunderbolt header 17-pin (18-1), 1x chassis intrusion header, 1x MSI tuning controller header 5-pin Header cooling 1x CPU fan 4-pin, 6x fan 4-pin, 1x pump 4-pin Header lighting 2x 4-pin RGB (+12V/G/R/B, max. 3A), 2x 3-pin ARGB (+5V/DATA/GND, max. 3A)
@KleoYan
6 ай бұрын
@@vegetarischerdrachenlord901honestly if you using all Arctic P12 or P14 ARGB. You don’t need a fan hub. All fans are daisy chainable, plus ampere drawn is low on both p12 / p14. Just make sure to do 3 x fans to a motherboard fan header. Plus MSI fan headers are all at 2ampere. It’s more than sufficient to drive all your fans that are done is set of 3. Example 3fans to sys_fan 1 , 3fans to sys_fan 2 and so on.
@vegetarischerdrachenlord901
6 ай бұрын
@@KleoYan Okay no hub sounds okay, ... So do you mean it would work and could be connected like: Top - 420 LF3 with 3 x 140mm fans exhaust -> on motherboard : 1x CPU fan 4-pin & 1x pump 4-pin & 1x 3-pin ARGB Side - 3 x 120mm fans intake -> 3x daisy chain -> on motherboard : 1x fan 4-pin & 1x 3-pin ARGB Bottom - 3 x 140mm fans intake -> 3x daisy chain -> on motherboard : 1x fan 4-pin & 1x ...? maybe 4-pin RGB compatible? Rear - 1 x 120mm fan exhaust -> on motherboard : 1x fan 4-pin & 1x ...? maybe 4-pin RGB compatible? btw i am not shure how I will do , so Version 1 or 2: Version 1 Top - 420 LF3 with 3 x 140mm fans exhaust Side - 3 x 120mm fans intake Bottom - 3 x 140mm fans intake Rear - 1 x 120mm fan exhaust - Total: 3 x 140mm fans 4 x 120mm fans Version 2 Top - 420 LF3 with 3 x 140mm fans exhaust Side - 2 x 140mm fans intake Bottom - 3 x 140mm fans intake Rear - 1 x 120mm fan exhaust - Total: 5 x 140mm fans 1 x 120mm fans
@KleoYan
6 ай бұрын
@@vegetarischerdrachenlord901 ARGB are to be connected to JARGB not JRGB. just this time. follow this diagram, if it's too small, zoom in or download the image i.imgur.com/mrZuqe3.png , ok am heading to bed it's 12:35am my time lol.. all the best. 😉
@JRDE56
2 ай бұрын
Hi is it possible to use the arctic freeze 420 aio with fans (67.5mm) with the low mobo setting and also use push/pull set up? With another set of sl inf 140.. … all together 92.5mm ?? Or would I need the 360 aio with 140 fans ???
@KleoYan
2 ай бұрын
Hi Jay Arr56, welcome to my channel. I do not advise you to run push pull configuration of a 420 liquid freezer 2 or 3 AIO at the top. 360 will still be ok.
@JRDE56
2 ай бұрын
@@KleoYan no worries. 360 will be fine then. Would it have to be with bottom mobo configuration? Also does 3 x 140mm fit accross the bottom with the 360 push/pull up top ??
@JRDE56
2 ай бұрын
@@KleoYan also thanks for the quick reply it helps alot
@KleoYan
2 ай бұрын
@@JRDE56you are most welcome and as for the bottom fans. Yes you can fit with the motherboard at low mode but will need to fiddle with the connection at the bottom as the gap is about 10 to 12mm of space.
@JRDE56
2 ай бұрын
@@KleoYan thanks very much. And this is with 3 x 140mm fans across the bottom. A push/ pull set up with a 360 aio up top and low mode on the mobo ? Is this correct ?
@JJ-gk5tn
9 ай бұрын
Hey kleo Please help me decide Montech King 95 or o11 Evo rgb I tend more towards king 95
@KleoYan
9 ай бұрын
Hi JJ, welcome back, I am also asking myself this quetion as both cases make use of what I like most.. Arctic Liquid Freezer II 280 and 420.. so it's very hard for me to answer.
@HLchwa
9 ай бұрын
O11 evo rgb cos it can be inverted if there is a need to
@JJ-gk5tn
9 ай бұрын
@@HLchwa I hate inverted builds I think they look ugly AF The king 95 is the better choice when it comes to value
@KleoYan
9 ай бұрын
I ended up, keeping both but I am more towards King 95 Pro due to it's uniqueness.
@KleoYan
9 ай бұрын
@@HLchwa Given the choice, I won't go inverted like JJ have mentioned. It's not able ugliness, is more on the placement and it's more time consuming to get it right with the thermal as I stay in a hot and humid country. We do not have four season here, it's always at 29°C to 33°C
@kof2
9 ай бұрын
Can I ask, is it possible to turn off the RGB?
@KleoYan
9 ай бұрын
Hi, derek cheong, welcome back and Merry Christmas! Yes you can turn it off. infact it's stated on Lian Li's official website about the Mode switch. just need to toggle the britness switch to 0% brightness and it will be off. M: Next/Previous Light Mode Button: Press 3 seconds to sync MB, press 3 seconds again to cancel. Go back and forth between lighting effects without needing to circle around the loop. C: Light Color Button: Switch between 11 colors, press 3 seconds to activate Pure Color Mode,press 3 seconds again to cancel. B: Light Brightness Button: Switch between 5 brightness levels-100%, 75%, 50%, 25%,0%.
@Adel-sj4ue
8 ай бұрын
Is this a new version of the evo
@KleoYan
8 ай бұрын
Hi Adel, welcome to my channel and yes, this is another Evo case which was released not too long ago.
Пікірлер: 358