Hey!! i forgot to tell you. Theres a thick film on those dash plates. You have to peel them, then they really shine!
@nuttersspeedshop
Жыл бұрын
I just ran out and peeled the lower plate. It's way better. Thanks for letting me know. I'll have to pull the gages again to peel the top plate.
@javinplaski5028
Жыл бұрын
Is this on the Shane jackson ones?
@nuttersspeedshop
Жыл бұрын
@@javinplaski5028 Yes it is.
@caddydaddy6728
Жыл бұрын
That's the water pump I'm going to try and rebuild same spi kit👍👍
@kurtkoutek7547
Жыл бұрын
Met these fellas at jumping jacks today. Nice group of guys. They even gave me stickers to put on my ski Doo. Thanks
@nuttersspeedshop
Жыл бұрын
Very cool! See you around the neighborhood!
@alaskarailroad3996
Жыл бұрын
Cool.....
@gordonliddy9418
Жыл бұрын
astro pneumatic makes a riv nut gun thats pretty reasonable.
@larrywarner9314
Жыл бұрын
I like those lights where are they available at
@nuttersspeedshop
Жыл бұрын
Lonnie says it was from a place called "Non Stock Society. He says they have a website.
@larrywarner9314
Жыл бұрын
That air foam I sent you I know you never received it I just got it back 2 days ago not sure why but it went to Michigan and sat there until last week when they sent it back
@nuttersspeedshop
Жыл бұрын
Thanks Larry. It's all good. We figured it out.
@jeffcarine9108
Жыл бұрын
I love those dash lights I gotta get a set for my xcr 800
@CAT5752
Жыл бұрын
Nutter, I have a request for you. Probably sounds dumb but i own two 95s, a Storm and an XLT. The cable that goes through the very front of the seat cover is different on both of them. So at least one is wrong, maybe both are? Could you shoot a short video showing exactly how that cable is ran and anchored? It would be much appreciated! Thanks man, keep 'em coming!
@nuttersspeedshop
Жыл бұрын
We're thrashing on sleds getting ready for Braapfest, but I'll try to get to this when I can.
@paulolsen6120
Жыл бұрын
She's lookin' good, Nutter! Also like the purple ski toes on the Grape Ape. Put a pair of grippers with 6" Woody's trailblazers on my XLT to replace the rusty steel skis - all I can say is WOW - what a difference! Thanks also for showing how you burp the cooling system after replacing the water pump - looks pretty simple. Never had to do it, but I know it's coming. Have a new water pump from Gilomen Innovations with the improved/removable bearing sitting on the shelf waiting for that day.
@nuttersspeedshop
Жыл бұрын
Thanks Paul! Good to know it's helping! I need to contact Gilomen and check into that pump.
@daveylboy
Жыл бұрын
I’m so glad I found your channel… you guys are awesome.. I’ve got a 98 xlt special and with your videos I’m gonna get my sled dialed in. How do I find the link for t shirts and stuff
@nuttersspeedshop
Жыл бұрын
Thanks. The link for shirts is in the description of the latest video.
@gregorywytenburg
Жыл бұрын
I second that ! Love all the XLT content , got a 94 XLT special myself
@raysdingo8223
Жыл бұрын
How or where do you grease the secondary clutch or drive shaft? Mine has a big black arrow pointing down behind it that says grease, no fitting? I'm liking that purple mesh in the louvers, mine has the slp ultra lite ski setup but no louver screens. Been hemin & hahing about those for a while.
@nuttersspeedshop
Жыл бұрын
Are you asking about greasing the bearings? If there's no grease nipple you'd have to pull the bearing out and look for a grease hole and use a rubber tip on the grease gun, or just replace them every few thousand.
@jeffmclearen1421
Жыл бұрын
Im in MN, where you guys at?
@nuttersspeedshop
Жыл бұрын
Stacy
@jeffmclearen1421
Жыл бұрын
@@nuttersspeedshop awesome. I got a cabin in Sandstone. Pass ya frequently. 👌🏽
@chadrosewicz1907
Жыл бұрын
Great Channel. Appreciate the content. Have a question I'm hoping you .ight be able to answer. Will the skid, track, axle and drivers from a 96 Ultra RMK work/fit in a 98 indy 500 that a a 121" track in it currently with little modifications. Thanks for any insight on this.
@nuttersspeedshop
Жыл бұрын
Depends on what you consider to be small modifications. Obviously the RMK track is longer so you will need a tunnel extension. Depending on which suspension they each have you may need to move the holes in the tunnel. The driveshaft and chain case should swap. It's not a bolt in.
@chadrosewicz1907
Жыл бұрын
Thanks. I have a complete parts sled that I bought just for the psi pipes for my ultra. It is a running driving sled but cosmeticly bad. Thinking about parting it out installing in my wife's 500. Thanks again.
@Mdubc25
Жыл бұрын
How difficult was the water pump rebuild with that kit? I picked up the same kit and haven't gotten around to doing the rebuild yet?
@nuttersspeedshop
Жыл бұрын
Those water pump castings are pretty delicate. You need to press the shaft and bearings out of the pulley and casting and it's a hard press. Most people will probably break a casting or break the pulley. Don't even bother trying to do this with a hammer. You need a press.
@brianblack387
Жыл бұрын
Nutter do you have a Indy 650?
@nuttersspeedshop
Жыл бұрын
Yes. There's a video of some work on it somewhere on the channel.
@SpeedX124
Жыл бұрын
Where can i find a parts list for a 96 indy 500 been looking but haven't found one 😔
@nuttersspeedshop
Жыл бұрын
Polaris snowmobiles web site has parts lists going back to 85.
@scottsweeney9647
Жыл бұрын
Hey Nutter, did you still need the correct handle bar pad cover? It’s hrs to tell in the video. I have one off a 95 XLT if you need one.
@nuttersspeedshop
Жыл бұрын
I do still need one. Shane Jackson was out.
@scottsweeney9647
Жыл бұрын
i got a used one i’ll send ya
@scottsweeney9647
Жыл бұрын
I went to pickup a used water pump so we could ride last week end. ended up with a tote full of 95 XLT parts
@nuttersspeedshop
Жыл бұрын
@@scottsweeney9647 Thanks!
@nuttersspeedshop
Жыл бұрын
@@scottsweeney9647 Awesome!
@andrewgasch9504
Жыл бұрын
Hey Nutter hows that waterpump kit holding up? I had the Triple Threat xlt at Triple Wars and had to put a used pump on before we went and been thinking about ordering that kit for my original pump.
@nuttersspeedshop
Жыл бұрын
Haven't put in the rebuilt XLT yet. The used pump is still holding up.
Пікірлер: 45