Reloaders have to be some of the most innovative folks. Those look great. Hopefully they’ll shoot great too👍🏻
@jamespollard1670
2 жыл бұрын
They look good and the idea sounds good . I can't wait to see the results .
@maxxbear5014
2 жыл бұрын
Thanks JAMES I’ll probably shoot them next week
@ericoulundsen5041
2 жыл бұрын
Those have to fly good I'm heading up to the garage right now to make one of those boards. Thanks for all the great info
@maxxbear5014
2 жыл бұрын
I’ll probably go to the range next week on Thursday and shoot them if you want to wait
@robertswyers4420
2 жыл бұрын
Very Cool and creative.I love the power of simplicity cheers
@maxxbear5014
2 жыл бұрын
Thanks. It working out pretty good
@ocean374
2 жыл бұрын
Looking good buddy thanks for sharing
@maxxbear5014
2 жыл бұрын
Thanks Julio 5 more days and I can shoot them at my new range.
@attaway9able
2 жыл бұрын
Can’t wait to see them fly!! 👍
@maxxbear5014
2 жыл бұрын
Tomorrow is the day!!!!!
@johnreynolds6499
2 жыл бұрын
Excellent!
@wonkachocolates6133
2 жыл бұрын
I subscribed & with a big thumbs up.!! Will you do a range & accuracy video?
@Hogheadsforbreakfast
2 жыл бұрын
Good stuff.
@russellmayberry1696
2 жыл бұрын
Great idea! What do you think about using a hot melt gun to do this?
@wonkachocolates6133
2 жыл бұрын
Please send over some of these for testing to TAUFLADERMAUS KZitem Channel.
@chrisuzmack1192
Жыл бұрын
That looks like a great idea, thanks for sharing. P.s. you sound like you're from Pittsburgh.
@maxxbear5014
Жыл бұрын
Yes I’m from the Pittsburgh area. I did modify the mold block I increased the gas seal a little. They shoot a lot straighter
@boozeandbullets2084
2 жыл бұрын
clever
@RobertSmith-ub6tk
6 ай бұрын
How do you make the board with two different size holes you said the bottom hole was one size and a top hose another I’m no woodworker but I’m confused
@maxxbear5014
6 ай бұрын
You drill the big hole only partway through then you drill the smaller hole to fit the slug. Thanks for your comment.
@RobertSmith-ub6tk
6 ай бұрын
lol thanks that’s what I was guessing. Love you video plan on doing that. did you ever do a range test? I didn’t see that video. Thank you. Have a blessed day.
@maxxbear5014
6 ай бұрын
Yes, I did a range test with them, but I only did it with mini slugs, nothing full length yet. They shot OK I only shot out to 50 yards@@RobertSmith-ub6tk
@user-jk2fu9gy6h
8 ай бұрын
WOOOW!!! GREAT IDEA will that plastic NOT MELT????
@maxxbear5014
8 ай бұрын
The plastic, is old shotgun wads I got from the trap range, so if they worked once they should work again
@MooreLeather
2 жыл бұрын
Have you had a chance to test these at the range yet? I'd be interested in the results you had using the fixed wad that you designed.
@maxxbear5014
2 жыл бұрын
I thought I made a video on that I think I was using a 20 inch Mossberg as I remember it the standard Lee 7/8 oz slug short just about as good as these dead
@MbalmR97TX
2 жыл бұрын
I think any plastic would work since wads are made from non-biodegradable?
@JBSurvive2Live
2 жыл бұрын
Nice~! :-)
@maxxbear5014
2 жыл бұрын
Thanks JB
@raymondbuie5292
6 ай бұрын
I thought interesting and wanted to know what your accuracy results were making your tail wads in this manner. Did you ever run them out to 100 yds?
@maxxbear5014
5 ай бұрын
At my range there is a gong just a big piece of metal about 15 inches round I shoot at that it’s about 100 yards I can consistently hit it but a 6 inch group I couldn’t say
@raymondbuie5292
5 ай бұрын
@@maxxbear5014 That is not bad really. I’m sure any of 30 variables in that can be tweaked. I am going to be experimenting throughout this year with them a bit in many different loads…. With a variety of base wads inside of the typical plastic wads. Also with Mylar and shot shell hull sleeves. May very well try your tail wads. I am working out this year on 12 ga socket slugs with 3/4” poplar dowel rod tail wad mechanically screwed to base of powder coated slug ( i’ve made complete jig set up for center drilling and casting) .
@rick31869
2 жыл бұрын
Brother that is some awesome 👏 stuff there ,job well done. So try this instead of melting plastic, try some with a hot glue gun ?
@maxxbear5014
2 жыл бұрын
I would but I don’t think I want to clean hot glue out of my barrel I think the friction might melt it thanks for watching the video
Пікірлер: 35