FINALLY SOMEONE SHOWING A MOTOR REPLACEMENT AND NOT A WHOLE ARM REPLACEMENT
@mr.existential3797
Жыл бұрын
Ikr, Jesus I was just gonna give up 😭 on my poor mini 2
@jeremyboyce1537
Жыл бұрын
Well I had to change a Motor at one time too but because the Arm was broken and wouldn't stay in place when I glued it back , I decided to buy the Arm with the Motor and Install it but normally , if the Motor is gone and the Arms are good , just change the Motor ! It is cheaper !!!
@jeremyboyce1537
Жыл бұрын
@@mr.existential3797, you can't give up on a Mini-2 !!!!
@briantucker5322
Жыл бұрын
I just repaired my DJI MIni 2 drone with this method. Thank you! This guy is a pro so it will take you much longer if you are like me and know nothing and have zero experience. (0:46) Step 1 of removing the panel on the arm took me a half-hour. Be careful! the arm is fragile. You are basically cutting the panel out (1:13) (2:12) Step 2 be very careful cutting the wires. There is a fourth grey wire for the arm LED light you don't want to cut. (1:46) Step 3 Remove round foam under the motor. This foam is highly fragile. I tore my foam (2:33) Soldering. This guy is a pro, but as someone who has never soldered before and bought a soldering iron for this project, this wasn't easy and took me over 2 hours. Make sure you put the heat shrink on the wires before soldering. (I noticed he didn't show the whole process.) I wish I was paying attention and used tweezers like him. These wires are tiny people. Maybe if I had real flux instead of the free hard resin flux from the kit it would have gone better. (4:00) I would suggest testing the motor before closing everything up. I did a test flight and noticed a weird, bad vibration if I put any strain on the motors. I thought the entire replacement project was a failure, but this was because the panel was still off. To put the panel on, you are going to need to use plastic epoxy or super glue, that is why he puts clamps on.
@jeremyboyce1537
Жыл бұрын
I did the same Repair to one of my Mini-2 's last couple Months and it is flying nice again ! There are three Mini-2's in my Arsenal and i fly the heck of them !!!😂
@clebersilvaimagensaereas.9493
3 ай бұрын
Show, belo trabalho, chegando pra prestigiar o canal, sucesso pra vc.
@denscorpio4666
Жыл бұрын
Встал такой же вопрос,смотрел видео с разборкой дрона,напрягся,но случайно увидел ваше видео.Большое спасибо за видео оригинального способа замены двигателя.Дрон новый,с самого начала клинит один мотор,наверное брак,немного раскрутишь пальцем и полетели,но всё равно лучше заменить.Теперь вдохновленный вашим способом,займусь ремонтом.Спасибо.
@user-cs7fy6ky9c
7 ай бұрын
Не нужно ничего менять, чашки легко выровнять по центральной оси. Если клинит то там просто грязь и нужно просто продуть и промыть. Такие дефекты возникают после транспортировки где происходит чрезмерное нажатие на чашки. Я купил дрон с рук и там все чашки восьмерят, выправил все отлично летает .... Хотя уже заказал новые движки, теперь просто лежат в запасе.
@denscorpio4666
7 ай бұрын
Спасибо,буду иметь ввиду,просто не хотелось бы применять силу к таким хрупким вещам.Сейчас просто перед каждым полётом немного раскручиваю рукой проблемную чашку.Дефект заклинивания проявляется только зимой и причина этому туго набитая смазка. @@user-cs7fy6ky9c
@siddharthwarvatkar1004
2 жыл бұрын
Very helpful .... Same problem happen with my mavic mini..... Thankyou for this video ....
@hkgeek2408
Жыл бұрын
which motor[model] did you use to replace the drone motor?
@robertohuerta6811
Жыл бұрын
What size is the shrink tube?
@BaaquliBoy1
Жыл бұрын
V. Helpfull thank you. I have a probelm with my dji mini2 ( power system hardware error ? Will u help me to solve pls ?
@jeremyboyce1537
Жыл бұрын
I Personally think the Mini-2, is the best thing since slice bread !!!!!
@roberth2747
Жыл бұрын
Mavic Air 2s would be the same way just change the motor not the whole arm?
@user-sj5ex6kl7l
5 ай бұрын
Hi I got mine sparky in the front engine… is it the same issue?
@GSM87
Жыл бұрын
Thanks for share!
@heshiebee
2 жыл бұрын
Thanks for this! Are all the motors the same? Does it matter if i buy a back one for a front arm?
@technico5880
2 жыл бұрын
I am not sure if all motors are the same but opposite motors (same prop rotation) are the same. I also used a Front motor. But I have the theory that all motors are the same and they only change the wiring for 2 of them in order to get the CW and CCW rotation.
@jameslawyer2993
2 жыл бұрын
Hey what are the clamps at the end for
@technico5880
2 жыл бұрын
I applied glue to the foam. The clamps should hold the foam in place and apply the necessary pressure
@diyirlrpg
2 жыл бұрын
Where can I get just a new motor and not whole arm? First time trying to fly it inside and it kept drifting off to the side and slightly bumped into the wall and auto shut off (error: motor unable to spin) flee it seemingly fine outside after that. But today I flew it again and when hovering or moving slowly it looks like it's losing torque every second or so as u can see the whole drone slightly and quickly tilting
@technico5880
2 жыл бұрын
I got my motors from an already used Mavic Mini. You can find plenty of this broken arms with an old motor attached that still runs even and smoothly and will otherwise end up in the trash. But there are also some (for example "Chinese") sellers, who offer you the motor only, for around 10 dollars each. Did you change your propellers after the crash?
@diyirlrpg
2 жыл бұрын
@@technico5880 no its was really soft hit tho.. and then it felt like 1 feet onto my bed. Could that screw up a motor that easily?
@technico5880
2 жыл бұрын
@@diyirlrpg I don't think so, provided the accident actually happened on soft ground. However, check that the motors are still running smoothly and recalibrate the sensors on a flat surface. That might help
@kb8839
2 жыл бұрын
Też tak mam ale nie naprawiam silnik działa
@mr.existential3797
Жыл бұрын
What’s that heating tool called for to remove the exterior part from the wires?
@technico5880
Жыл бұрын
What do you mean? The solder iron?
@mr.existential3797
Жыл бұрын
@@technico5880 I thinks so, is it the like little metal pen to cut the wires?
@technico5880
Жыл бұрын
@@mr.existential3797 I think you mean the knife, it's a simple knife, not heated to remove the isolation
@chenakos
Жыл бұрын
I have exactly the same issue with my Mini SE. Why is this done? A faulty motor? I presume it is dangerous...
@technico5880
Жыл бұрын
The motor was not running smoth, that's the reason for the replacement.
Пікірлер: 36