Check out Www.snacksforme.com for some of the best snacks!!
@5171eric
4 ай бұрын
I shared this video with my mechanic who initially suggested I replace the entire transfer case. He replaced the $100 chain and my ML350 runs great. Thank you for posting.
@Vdoman1
Жыл бұрын
Wow! You made that look so easy! My 2014 ML350 Bluetec just started skipping-- 117K miles-- I replaced the motor mounts and transmission mount about 3 months ago. They were a pain! Took me two days. Really enjoyed your professional quality audio and video! Thank you!
@CodytheCarGuy
Ай бұрын
Thanks I try to make the videos as best I can while showing the best way to get it done.
@NigelMarston
6 ай бұрын
My GL is at 130K miles now and still not skipping but I can't help think perhaps I ought to change this chain anyway to pre-empt any issues which might cause wear on the sprockets. The transfer case has had two oil changes since I bought it at 38K miles so I hope I've staved-off any wear so far. Thing is, the GL has high/low range and I believe the chain is different which I'm struggling to find here in the UK. If anyone has a part No, I'd be grateful. Thanks, and thanks for the video. This was extremely helpful. My only fear is working underneath the car. I have monstrous axle stands (6 tons each) and a 3 ton trolley jack but when I changed the airbag springs, I still couldn't bring myself to get under it. It's a bit of an irrational phobia I guess.
@marvinmarcus5957
20 күн бұрын
While fitting the case comer be careful not to rub off the RTV if not you will have a leak after
@DOUGSVIDEO999
8 ай бұрын
My factory MB manual gives their "two-step" torque technique for the driveshaft bolts, torquing to an initial value in phase 1, then turning an additional 90 degrees in phase 2. The values differ for front and rear. In the front at the transfer case, it is 40 Nm, plus 90 degrees, in the rear at the diff it is 60 Nm, plus 90 degrees. In US measure (conversion factor is 1.356) that is 29 foot pounds plus 90 degrees in front at the case, and 44 foot pounds plus 90 degrees in the rear at the diff.
@LamontThompsonFilmMaker
9 ай бұрын
Made that look too easy lol. Where are you located? Must be the south because I heard a rooster in the background in the beginning of the video.
@shawnmrfixitlee6478
Жыл бұрын
Great work Cody .. it was time to do that before it tore up the case and bearings .. You saved her a ton of $$...
@CodytheCarGuy
Жыл бұрын
Well she told me it was clicking but kept driving it so she was very lucky. I actually did the repair a year ago but just now got it edited and uploaded. Soon I'll get my cherokee build uploaded.
@shawnmrfixitlee6478
Жыл бұрын
@@CodytheCarGuy yes.. Jeep guy here !
@CodytheCarGuy
Жыл бұрын
@shawnmrfixitlee6478 this is my 03 WJ build, bigger rad, deleted the hydraulic fan, lifted, winch bumper, lockers, and soon the h.o. engine with headers. I use it to pull my stump grinder for the tree service.
@shawnmrfixitlee6478
Жыл бұрын
@@CodytheCarGuy SWEET ! keep the jeep burn the EV'S .. 0IIIIIII0
@CodytheCarGuy
Жыл бұрын
@shawnmrfixitlee6478 ha ha guess what I have some prius videos coming up lol I bought one to run back and forth to my ranch when fuel was sky high. The f250 w the 7.3 only gets 10mpg so got the prius so I can run out there and feed the animals and water the giant garden.
@ionstamatin6080
17 күн бұрын
What is a good brand for the chain ?
@DOUGSVIDEO999
7 ай бұрын
On my 2011 ML350 Bluetec I found the driveshaft bolts were T55 rather than T50
@MrRadlom
11 ай бұрын
Great video! Thank you. Could not remove my driveshaft from transfer case though, all bolts out, soaked with rust blaster and still won’t budge. Had to do complete chain chain out with section still attached to driveshaft. any hint on how to separate both? Thank you. Rick
@yaoaoussi
10 ай бұрын
You just have to hammer it
@user-mi5pp6kv9m
7 ай бұрын
Hi Cody, You have agreed to do collab with us and took the product from us and never created a video and posted on your social media channel. Can you please tell me any ETA when you can post? Product was sent to you in August 2023!
@wandathorpe6471
Жыл бұрын
I absolutely luv watching your videos! I have this same vehicle but wldnt dare attempt to take apart like you just did but very fun to watch. Tks for sharing.
@CodytheCarGuy
Жыл бұрын
Thanks! Ahhh it wasn't that bad just took some time. I've been building transmissions and transfer cases since I was a kid building 4x4 lifted trucks. And have several awd vehicles myself, and guess who has to do all the repairs lol
@OttoThompsonReviews
Жыл бұрын
You never put the foot punds for the drive shaft.
@danieleriksson1657
9 ай бұрын
I just changed the fluid in my transfer case in a W251 -07 chassi after 70k miles, and the transfer case inside was metal clean, the oil was little bit dark red, how come this one was so dirty and full of sludge? How many miles your car had?
@yaoaoussi
10 ай бұрын
Thanks for your video,i was able to get it done but now the car won’t start 😢😢. Have power but it won’t crank. Any idea what can be the issue?? The air suspension compressor too is dead
@im_a_bigdog7772
9 ай бұрын
did u get car started?
@im_a_bigdog7772
10 ай бұрын
how much would this job cost roughly at service shop??
@OttoThompsonReviews
Жыл бұрын
Whats the torx for the bolts on the rear drive shaft?
@repairvehicle
Жыл бұрын
Nice work!
@CodytheCarGuy
Жыл бұрын
Thanks! Editing the video almost took as long as doing the repair.
@OttoThompsonReviews
Жыл бұрын
How long did it take you to complete the work on this.
@CodytheCarGuy
Жыл бұрын
2 or 3 days because I was filming and the owner ordered in the fluid so I had to wait on that, along with filming. But this can easily be done in a day.
Пікірлер: 37