I think this is brilliant. Too much of online content now is this carefully curated view of the world where everyone thinks that everyone else is perfect. I think it leads people to give up and not even try. Showing it all, including the warts, is so refreshing and so real. Bravo!
@10MinuteWorkshop
Жыл бұрын
Thank you! 👍
@ozzyeyre
Жыл бұрын
You just made a whole load of people feel so much better about their own efforts. Please accept these thanks from one if them!
@10MinuteWorkshop
Жыл бұрын
Thank you, I will! 👍👍
@AbdicateDotNet
Жыл бұрын
Loved the "issues" video. I've seen others incorporate their mistakes, yet others do "Technical Difficulties" at the end. Either way, truth is better than perfection because it helps newbies know we're doing just as fine as the big-named folks. Thanks, sir!
@stewness3863
Жыл бұрын
Seeing you point out the mistakes and as you say, how you get over them, makes me feel a lot better about my own work. Everything takes 3 times as long because I make it, see the issues/mistakes and then mess about trying to rectify them only to realise I need to start all over again because it now looks like a dogs dinner! I have started to call it prototyping!!!
@10MinuteWorkshop
Жыл бұрын
Thank you! 👍
@chrish247
Жыл бұрын
Haha you're not alone mate 😂
@Mikey__R
Жыл бұрын
Prototyping! I love it!
@ahorton6786
Жыл бұрын
I'm only making "prototypes" at the moment!
@matthewwysocki5019
7 ай бұрын
Transparency is good for the soul. Thanks for sharing. “Howlers” is my middle name when it comes to projects. I used to get angry and disappointed with myself. Now I just laugh it off. Reset and fix, remake, and pray.
@timothynitz8118
Жыл бұрын
It's always good to show mistakes. I appreciate it, makes me feel less "unique"! I also learn a lot from how we overcome them. Someone once said that the primary skill of a woodworker was knowing how to cover up mistakes. I believe that.
@LightraysPhotography
Жыл бұрын
Thank you so much. I feel much better now seeing a pro mess up and fix his errors. I really enjoy your videos.
@10MinuteWorkshop
Жыл бұрын
Thank you! 👍
@TheMixmastamike1000
Жыл бұрын
I really enjoy, or find solace in seeing the people I admire share their mistakes because it helps beat back the imposter syndrome that I deal with.
@DavePawson
Жыл бұрын
No, not a pity party Peter. Good to see your solutions! We've all done the same / or worse
@Mike----
Жыл бұрын
The timing of this video is impeccable. I just put down my tools and gave up for the night because I made a drawer with no bottom. Thanks for adding some company to my misery. Good to know I'm not alone.
@10MinuteWorkshop
Жыл бұрын
Sometimes walking away is the best solution; tomorrow is another day. 👍
@trevorwinter5071
Жыл бұрын
It was encouraging seeing that someone else makes mistakes, can admit to them and rectify. I am 84, still woodworking and enjoying it but do seem to make more mistakes now. I have found that it is often possible to turn a mistake into a feature, sometimes a decidedly improving feature. Bob Ross the American artist said “ there are no mistakes just happy accidents”. The sign of a really competent craftsman shows up in their ability to solve problems.
@lrr1952
Жыл бұрын
Thanks Peter, for showing us hobbyist woodworkers that even a pro can make a mistake once in awhile. My last project was making some boxes for storage in my shop. Basically open cabinets with back, but no doors. I was assembling the tops and bottoms to sides, using my Domino. I was mindful that tops and bottoms should be fastened between the sides (end panels). And thanks for pointing that out in another video! I got so mixed up about which side of each piece to reference the cuts from (inside face, or outer face), plus whether I was plunging into surfaces, or panel ends (edges), not to mention which cuts were standard width, and which were wider fit. After a few mistakes, I finally resorted to making detailed pencil notes on each piece! These storage boxes were for my basement shop, mounted high on walls, so a few incorrect mortises got hidden by facing them up on those panels, at the top of the cabinet. Only I know they are there! 😊
@10MinuteWorkshop
Жыл бұрын
That’s all that matters! 👍👍
@stvcolwill
Жыл бұрын
I’m really glad you did this video, not only is it healthy but entertaining and educational. Kudos.
@10MinuteWorkshop
Жыл бұрын
Thanks! 👍
@andrewpinson1268
Жыл бұрын
Don't take this wrong, but I was so HAPPY to see you make those mistakes. You are way ahead of me in woodworking, but still do what I do way to often. And these are difficult to repair so thanks for showing how you climbed out of this.
@10MinuteWorkshop
Жыл бұрын
Thanks! I think that’s the most important part, showing how to get out of the jam you got yourself into! 😂👍
@chipsterb4946
Жыл бұрын
Best lesson ever! We all make mistakes but the craftsman knows how to recover from them. Maybe someday I’ll be a craftsman… 🤓
@nicolassimard5847
Жыл бұрын
Peter, It’s never too late for ADD pills. I’m 48 and just started 🤭. Seriously, thank you so much for comforting me. As a beginner, it is sometimes frustrating to make so many of these mistakes. But it is warming to see that even the pros need to catch up because they screw up. Thanks again !
@MS-do5xq
Жыл бұрын
We always see the flaws in our work, even though everyone else sees perfection. Knowing this doesn't help me feel any better when I make a bone-headed mistake 😂. I do applaud you for showing yours, it makes your content relatable to the rest of us as most on the internet would not.
@10MinuteWorkshop
Жыл бұрын
Thanks! 👍
@gav2759
Жыл бұрын
I've lost count of the number of times a mistake, or the recovery from it, can actually enhance a piece....It is my ability to convince my self of that fact, that has developed into my greatest skill. I always acknowledge a KZitemr who fesses up to the odd slip, thanks for posting.
@10MinuteWorkshop
Жыл бұрын
Thank you! 👍
@troyboy4345
Жыл бұрын
Ah Peter, this just backs up what people think of you on here, a decent honest bloke, free to share his experiences, really enjoyed that mate !
@10MinuteWorkshop
Жыл бұрын
Haha, thanks! 👍
@sackville_bagginsess
Жыл бұрын
All my hobby projects are filled with avoidable mistakes like this. I get so cross as myself, put my tools down then have to come back. I really appreicate you showing these. Often KZitemrs present a perfect project and that can be demoralising when you come to try it yourself and hit road blocks.
@10MinuteWorkshop
Жыл бұрын
Thank you! 👍
@cliveclapham6451
Жыл бұрын
Avoidable mistakes are the hallmark of bespoke furniture❤ There’s a bloke that makes “square’e’nough” squares might wana give him a look for pointers 🎯🤦🏻🤣
@thomlipiczky9021
Жыл бұрын
I'm just taking a break from fixing a very similar mistake (miscutting a solid maple board that was supposed to have continuous grain across the drawer fronts) to watch you excellent video. I didn't bother to mark out the blanks with lots of tape and pencilled triangles. I thought I could keep track of it all. Hah! Thanks again, Peter.
@triplex86
Жыл бұрын
Fantastic that you are good enough to post a vid like this and show that, sometimes, even the expert's best made plans just go t**ts up. I'm sure there are hundreds of weekend carpenters out there, like me, thinking, yeah, I did that. As you say, the important thing is how you deal with the mistake. Thanks.
@10MinuteWorkshop
Жыл бұрын
Thanks 👍
@happychappy2b252
Жыл бұрын
Perfect admission that we all occasionally are less than perfect. As you say.. it's what comes next that defines the work, the person, the organisation. I think we are all glad to see that we are normal and i thank you for sharing it with us.
@stevebosun7410
Жыл бұрын
Well done Peter, thanks for your honesty.
@tjacksonwoodworker3726
Жыл бұрын
I appreciate you showing this...somewhat encouraging for a duffer like me. I have been woodworking for a long time and still make a mistake or two on every project. Some turn out to be design features.
@10MinuteWorkshop
Жыл бұрын
Every project needs a ‘design feature’ 👍😆
@lionandbear
Жыл бұрын
If I didn’t show my mistakes then I’d have no content! 😂 it’s nice to see that even a seasoned pro like you has the odd mishap, makes us hobbyists and beginners feel much better about ourselves.
@yossiyaari3760
Жыл бұрын
Publishing some of the members only content, months after the exclusive access, is brilliant. I don't think I've seen that done on other channels. If you don't mind my mentioning it 🙂
@10MinuteWorkshop
Жыл бұрын
Thank you! Hope you liked it! 👍
@iteachtime
Жыл бұрын
Been there many times. Thanks Peter for sharing.
@imcg
Жыл бұрын
Couldn't of timed this video better 😅 had a mare installing a record vice revently.. got there in the end. Good to see how the pros get over the errors
@alansimpson596
Жыл бұрын
I've been a hobby woodturner for about 10 years and I've learned so much from the howlers that I made and continue to do so.
@peterpage7322
Жыл бұрын
And there was me thinking you were perfect! Well, I still think your work is 😂! Also it’s nice to see that you are human too and another great video, thank you, you just gave thousands of viewers some hope!
@andyc972
Жыл бұрын
Well that was very honest of you Peter, I hope you feel better for that ! 😉😁 It's so often the case, you take hours to plan and cut the parts to size, then decide to get a wiggle on or just lose concentration for a moment and boom it's all gone off piste, much better a small (albeit annoying) cosmetic fault than injuring yourself though, which is an alternative scenario ! ☝🚑😬
@10MinuteWorkshop
Жыл бұрын
Thank you! 👍
@54mgtf22
Жыл бұрын
But at least you did it, ‘Your Way.’
@christopherjacklin7589
Жыл бұрын
We've all been there. All the cabinets in my kitchen are a few mil shorter than I intended as I spent a whole day with my rail fractionally out of square...! The only people who don't make mistakes are people who don't make anything.
@davidmeyer9204
Жыл бұрын
Thank you for sharing this! When I start to make something I always tell my self "make it look like some one else made it"
@kristoffscuba5466
Жыл бұрын
I made some Millard-style fitted wardrobes last year. Biggest project I’d ever done. Massive things across the whole room. Took my time on breaking the sheets down and the dowel assembly, got them all perfect, but i fitted the hardboard backs to the carcasses as a rough fit, face down; and routed the excess off with a trim router. That seemed to me a quick way of doing it on these massive wardrobes. It was clearly stupid though as it meant I couldn’t guarantee the carcasses were square. Which of course they now wernt. I glued them all up and fitted them together on the plinths, screwed them down, made the scribed trim, went to fit the doors and realised my mistake. I had made parallelograms not rectangles. 😡😡😡. I had to trim the doors all skewiff (Millard term) to correct the error and I’ve never swore so much in my life. You’d never know to look at them, but man that was 12 months ago and I’m still fuming each time go in the room. The amount of headaches that caused. And I saved maybe 5 minutes over track-sawing the backs to the correct dimensions and fitting them.
@dougsaunders8109
Жыл бұрын
lol, I have made the parallelogram mistake
@10MinuteWorkshop
Жыл бұрын
Classic! We’ve all been there - and it always hurts the most when it’s something you have to look at daily! 🤷♂️👍
@michaelburton4521
Жыл бұрын
Hullo Peter A few weeks ago, I assembled an IKEA wardrobe for a client. I was putting the last 10 or so nails in the back and I realised the white side was facing outwards. And those nails are ring shanks, so they are difficult to get out without damaging the laminate. Later on in the same job I drilled a lovely 4.5mm hole for the handle - in the hinge side of the door! The closest IKEA to Walton on Thames is Reading, about an hour away. Sheesh
@10MinuteWorkshop
Жыл бұрын
So easily done as well Michael! At least it wasn’t bespoke! 😂👍
@robertcrossley9803
Жыл бұрын
we all make mistakes. It's a good man who knows of a mistake Its a great man who will put up his hand and say he has made a mistake. Great video's Peter thanks for taking the time
@10MinuteWorkshop
Жыл бұрын
Thanks Robert! 👍
@Andy-te6jj
Жыл бұрын
who does not make mistakes, still turned out great, no one (except you) will ever notice that the grain matches perfectly, like the way you react and not over react
@10MinuteWorkshop
Жыл бұрын
Thanks! 👍
@tonysutton6559
Жыл бұрын
My night school woodwork teacher used to say "don't call them mistakes, call them features" while at work in my day job I used to say "don't look on it as a mistake, tell people it's an opportunity to find a solution"
@kevinwood9993
10 ай бұрын
Thanks for sharing, as always, always a joy.
@10MinuteWorkshop
10 ай бұрын
Thank you! 🙌
@janesimons3068
Жыл бұрын
Peter, made the same mistake on a small book shelf, that Festool came to my aid. Thank you for sharing. I took up wood work in my late sixties, love every bit of it. Ps I am Great Grand Ma
@10MinuteWorkshop
Жыл бұрын
Thank you Jane, and congratulations! 👍
@saiiiiiii1
Жыл бұрын
Peter the kind of guy you want to have as a neighbour 😁👍
@10MinuteWorkshop
Жыл бұрын
That’s not what my neighbours say after a summer of building work… 😬
@Viken43
Жыл бұрын
Any fool can make mistakes, but it takes a craftsman to resolve them. Thanks Mr Peter, just shows you are human after all 😂
@10MinuteWorkshop
Жыл бұрын
Thank you! 👍
@splinters_66
Жыл бұрын
The old saying, the difference between a professional woodworker and an amateur woodworker is the ability to hide your mistakes. I prefer to think of them as challenges, mistakes can always be fixed.
@Mr_Judge_Benny_Hinn
Жыл бұрын
And bad mistakes - I've made a few - I've had my share of kickback on the table saw But I've come through... We are wood workers my friends...And we'll keep on wood working till the end...
@lollybolly1000
Жыл бұрын
I'm making four simple boxes to store towels and bathroom items. I have cut a couple of sheets of mdf down to the size boards I need and marked them up with which face should be inside/outside. Where all the peanut fixings should go etc, but I then left them hanging around for a month as I kind of got anxiety about all the simple mistakes I can make during the process of routing and assembling the boxes. I am literally assembling them in my head daily and working through all the possible mistakes I can make. I have ploughed on with plenty of other projects, but I'm stuck on this one. Guess I should just crack on with it and work through any mistakes if and when they happen. If it turns out to be a potential I've made a few mistakes video in my head, well so be it.
@donaldbiehl1733
Жыл бұрын
Two things… a Swiss cabinetmaker told me forty-five years ago a mistake is something that can’t be fixed. As apprentices, they had to compile a notebook of their mistakes and why “it” happened so they would only make them once. The best students were those with the thickest notebooks. And, number two, you still some smaller Baltic birch pieces to work with. JSK Koubou provides many KZitem videos utilizing such smaller pieces.
@terrychristian672
Жыл бұрын
Thanks Peter. Glad I’m not the only one making bonehead mistakes.
@johnthresher259
Жыл бұрын
A couple of mm out is fine to use mere mortals Peter! The trick is don't tell anyone. Only Robin Clevett would notice! 😂
@10MinuteWorkshop
Жыл бұрын
😂😂👍
@hendrst1918
Жыл бұрын
I definitely enjoyed this. Let me contribute my own recent mistake. I tapered one of the legs on a cherry coffee table on the wrong side. All of the legs have two tapers facing the inside. I tapered one leg with one of the tapers facing the outside. Unfortunately I didn't notice the error until well after glue-up so it can't be fixed. The odd thing is that it is not obvious to a casual observer and even fooled me for a few days. I think the reason is that curves fool the eye. If I had the tabletop even slightly out of alignment or if the legs had been straight and one slightly thicker than the others I would have noticed it immediately. But curve those legs and you can (almost) get away with even a major error. So the table will not be in the living room but will be consigned to the upstairs office. Still pretty to look at even with a bum leg. PS: I have never made anything without some error mostly fixable though.
@10MinuteWorkshop
Жыл бұрын
Classic! 🙌
@MCsCreations
Жыл бұрын
Well... As an old and wise man once said... Shit happens. 😬 A good idea is to mark the parts with blue tape and write on it with a thick pen, instead of marking directly in the wood, Peter. Because, this way, it's much more easy to spot the right side. 😉 Anyway, stay safe there with your family! 🖖😊
@anthonyseiver7000
Жыл бұрын
Pity party has a confession corner obviously. Drilling through a finished tabletop twice 😢
@10MinuteWorkshop
Жыл бұрын
😂👍
@kevinthomson6324
Жыл бұрын
As a person who almost never marks parts at all thinking how hard is it to keep track…. That’s why I’ve never even considered “grain matching”
@MrSmith-uk8hq
Жыл бұрын
School boy mistakes, you naughty boy Peter! Watta mistakah to makah....
@ashleycox432
Жыл бұрын
Ah, mistakes. I recently build a new router table, the intention being ot build a nice table top and a cabinet to go underneath. However I made so many mistakes on the cabinet I ended up bolting my new table top to the old legs of the original Rutlands router table and smashing the new cabinet to bits to at least reuse some of the material. I made mistakes on the table top too, forgetting to tighten the micro adjustment on the router fence when cutting the table fence slots which caused the router to wonder and cut a curved slot that had to be routed out and replaced with acrylic plates, though that was actually an advantage as it makes the fence lock securely to the table as the bolts aren't biting into soft MDF. I don't know what it is about some projects, but some of them just don't go well no matter what you do. For me it's usually cabinetry. A couple of years ago I spent £200 on B&Q oak-effect melamine shipboard furniture board (stupid) and used it to build a hi-fi cabinet. I didn't have a track saw at the time, nor a table saw that could accommodate a big enough cross-cutting sled. So I resorted to cutting the panels with a straight edge and a router to get a clean cut that didn't chip at the edges. The problems arose as some of my panels weren't perfectly square, and the chipboard core was utter crap. When the cabinet was eventually together I set about drilling the shelf pin holes with a Kreg shelf pin jig (which itself is utter rubbish) and the variable density of the chipboard core caused the holes to wonder out of alignment. It wasn't much, only a half a millimetre in either direction, but it was enough to cause the shelves to rock or to sit out of level which wasn't good enough for sensitive stereo components. The worst part is I'd glued the cabinet together with polyurethane glue, so I couldn't get it apart without involving a hammer. I smashed that project to bits out of sheer frustration and kept some of the material for use in other projects, but eventually I realised the material was just rubbish so junked the log. Kept finding small pieces all over the workshop for months, as if it were coming back to haunt me. I still regret that failure even now, so much so I have yet ot find the confidence to repeat it and ended up buying an Ikea cabinet for the stereo gear. It's nice to know that people who have been doing this for a lot longer than I still cock it up.
@dougsaunders8109
Жыл бұрын
I have smash stuff up in frustration…..😂 Definitely good materials make life easier. The other thing is a jointer and thicknesser. You get straight square stock to work with
@10MinuteWorkshop
Жыл бұрын
Ashley, I’ve made so many similar mistakes it’s not even funny any more. And I 100% agree that some projects just don’t go well; it’s not your day and things aren’t meant to be. But you know what? The day ends, another day - and another project - begins, and as long as you learn from what happened the next project will be better. 👍
@MikeSplicer
Жыл бұрын
Once put the 5th mirror in a set of doors the wrong way showing the back of the mirror to the world. Used my tracksaw to cut out the mirror from the frame and reverse it
@10MinuteWorkshop
Жыл бұрын
Got to love a tracksaw! 👍
@rickkinney1249
Жыл бұрын
i have been there!! rick
@DesandSam
Жыл бұрын
I was doing a 'modification' to an existing IKEA (sorry) tv/media unit. I'd bought a new surround sound amp that was slightly too deep for cabinet. I decided to remove the flimsy hardboard back, glue it to a sheet of mdf, cut out a port to accommodate the amp and all its cables then remount the more robust back panel. After much marking out, measuring, remeasuring, careful cutting and sanding, I offered up the new panel in all its glory, it slipped beautifully into place. And none of it lined up. Not even close. I don't know what I did wrong. I had to cut out an even bigger (gaping hole) rectangle. Not the finessed bespoke solution I was hoping for. I call it a practise piece.
@10MinuteWorkshop
Жыл бұрын
You always need a test piece. 👍
@Cradley684
Жыл бұрын
Suck it up Pete, we are human xxxx happens, try and have a nice day Mate !!!. 👍👍.
@coop_coop007
Жыл бұрын
Confessions of a closet maker. I'm sure these films were popular in the 70's....
@10MinuteWorkshop
Жыл бұрын
😂😂 Confessions of a driving instructor; do you know the way to Oldham..? 🤷♂️
@billk8780
Жыл бұрын
Thanks for this. It's why I avoid pens and only use pencils which have erasers on them.
@kevinthomson6324
Жыл бұрын
You may need to look up this reference. But to quote Al Bundy. “There’s no mix up a sander can’t fix up !
@70newlife
Жыл бұрын
I think the key point you need to take care of is get up from the right side of the bed In the morning!! 😂😂
@10MinuteWorkshop
Жыл бұрын
😂😂 Absolutely! 👍👍
@johnfitzgerald4274
11 ай бұрын
Always, always mark face side, face edge, and stick to your own rule about orientation, i.e. face side inside, face edge to the front (or back), may I suggest.
@electronerd
Жыл бұрын
If it weren't for the splintering, you could have put grooves on the outside of the rest of the drawer fronts and called it a detail :D
@ExMachinaEngineering
9 ай бұрын
Is the title a reference to the Bohemian Rhapsody? Cool vid by the way.
@10MinuteWorkshop
9 ай бұрын
Thanks! And no, ‘My Way’ Frank Sinatra.
@SweSuf
11 ай бұрын
A too frequent one for me is to mentally be a step ahead, as in executing steps A, B, D, and E, and only then realising that C was skipped...
@jamespeterson686
Жыл бұрын
How does one purchase the LTJ30?
@10MinuteWorkshop
Жыл бұрын
There’s a link in the description, and a store link directly beneath the video. 👍 “Visit the 10MinuteWorkshop store for the Loose Tenon Jig 30 and ‘Square Enough’ assembly guides at www.10minute.shop”
@richardhart7652
Жыл бұрын
To err is only human,but if you arrrr your a pirate 😅
@Kiss4cooper
Жыл бұрын
I get the Frank Sinatra lyric reference 🙂
@richardmoss9188
Жыл бұрын
But at least you did it your waaaay
@hansangb
Жыл бұрын
When making shelves, I've been known to no mirror the left and right. So the rabbet for one is on the wrong side. That's the problem of batching...you go on auto pilot and a) it gets dangerous - not pay attention or b) you make the wrong cut.
@10MinuteWorkshop
Жыл бұрын
So easily done! 👍
@davidstreet3505
Жыл бұрын
Ha ha We have all been there and been bitten on the bum by a mistake or an oversight.
@10MinuteWorkshop
Жыл бұрын
Oh yes! 😂
@paulbarnard5267
Жыл бұрын
I’m forever putting dominoes in the wrong edge or plunging right through the panel. Fortunately I’ve not done it on a project I wasn’t painting so relatively easy to hide the errors. As they say, to err is human, to really screw up you need power tools.
@10MinuteWorkshop
Жыл бұрын
😂😂👍
@dougsaunders8109
Жыл бұрын
Those who make the most mistakes do the most work. No mistakes = no work Last night glueing up a door, classic shaker MDF with groove and panel, liberal amounts of glue everywhere I had not cut the domino slots deep enough because I had written the wrong size on the bag! A certain amount of equally liberal swearing I had cut 10mm off 12 dominos all good The most recent of many mistakes! Many due to grooves in wrong face like your draw front, so easily done
@10MinuteWorkshop
Жыл бұрын
Well said! 👍
@dougsaunders8109
Жыл бұрын
@@djstuc 😁 ok I may have been a bit of the wrong way around
@dougsaunders8109
Жыл бұрын
@@djstuc 100 whichever way you say it mate 👍🏻
@davidfarnall3211
Жыл бұрын
Ha! My first comment, maybe, added to my millionth mistake. Still learning from them though, bug with increasingly gritted teeth 🙄🤦🏻♂️!
@Ianf1x
Жыл бұрын
I would like to tell you all the mistakes I have made if you have 10 years to spare 🤣
@10MinuteWorkshop
Жыл бұрын
😂👍
@WPGinfo
Жыл бұрын
Perfection is overrated! Seriously! Life is complicated, messy and shit happens, despite our best efforts. The problem with social media these days is that we are shown [near] perfection; not by craftsmanship, but by video-editing the mistakes out. I think that poses a big problem for today's youngsters: How will they learn how to deal with 'real life', solve problems, manage [realistic] expectations, 'make do' with whatever comes out of the process... Dealing with / overcoming FUBAR is a valuable life-skill. We learn the most valuable lessons by messing up.
@brucewelty7684
11 ай бұрын
🤣🤣
@frankderks1150
Жыл бұрын
You are at that age to start considering measuring twice.
@riba2233
Жыл бұрын
Measure once curse twice 😅
@gavanwhatever8196
Жыл бұрын
But then again, too few to mention...
@PaulSage
Жыл бұрын
But then, again, too few to mention
@Scott-g9t
Жыл бұрын
I notice you don’t have any “bleeped” out audio ever…….are you that disciplined as to never let an f-bomb slip or do you just remove it during the editing process?
@10MinuteWorkshop
Жыл бұрын
I’m very disciplined when the camera’s running, not so much when it isn’t! 😂👍
@WobblycogsUk
Жыл бұрын
I bet you really kicked yourself when you routed that groove on the wrong face. We've all done it but knowing that doesn't make you feel any better at the time.
@10MinuteWorkshop
Жыл бұрын
Beyond angry with myself! Infuriating! 😂😂
@bigmonkey999888
Жыл бұрын
Hi Peter just lost my bet with myself though today you would be reviewing Benchdogs latest addition to Festool CSCSYS 50 Steve
@10MinuteWorkshop
Жыл бұрын
If I had it I would have! 🤷♂️👍
@fuzzzeballs
9 ай бұрын
confabulation errors, the falacy of the human mind
@10MinuteWorkshop
9 ай бұрын
Always! 🤷♂️👍
@pietdixon3232
Жыл бұрын
As an apprentice I was often told not to show the mistakes I made, certainly don't tell whoever was buying it. Just pretend that they are not there. Only another woodworker would notice. I was always of the opinion that I couldn't cheat the paying customer, It's dishonest, and I am always proud of what I make. Nice to hear you say the same. Thanks for showing us that even the Gods make them.
@10MinuteWorkshop
Жыл бұрын
Thank you! 🙌
@whitebeard2407
Жыл бұрын
Thanks so much for being willing to share your mistakes. The world of KZitem always makes things look easy and it’s not very often things go so smoothly in real life. It’s easy to lose confidence in your own abilities when all you see on the screen is perfection.
@10MinuteWorkshop
Жыл бұрын
Thank you! 👍
@petercarter5732
Жыл бұрын
Yes we all make mistakes but few own up to them I used PU glue for the first time normally use Pva - oh I put too much on - bit of a leaning curve I think
@john900ra3
Жыл бұрын
fantastic, keeps things real
@10MinuteWorkshop
Жыл бұрын
Thanks! 👍
@bigmonkey999888
Жыл бұрын
Hi Peter, some days it’s just turning the key in the workshop door! LOL Steve
@10MinuteWorkshop
Жыл бұрын
True that, Steve! 😂👍
@weldabar
Жыл бұрын
The internet is full of fake perfection, not just in woodworking. It leaves people thinking less of themselves. So YES it is absolutely okay to show us some of your imperfections. Remember: Measure twice, cut once. (or my personal version, measure thrice)
@10MinuteWorkshop
Жыл бұрын
👍👍
@ted6499
Жыл бұрын
Yes , your right , in this world of online sites , it seems nobody makes mistakes ….! Yes they do , even a master like you Peter …. Thanks for sharing , it makes us all feel like where not that bad after all !😅👍👍👍👍 10 minute workshop …. Ace ….👍👍👍
@10MinuteWorkshop
Жыл бұрын
Thanks Ted! 👍
@gordonlamb6034
Жыл бұрын
In the middle of my drawer project and making at least one mistake a day. Grooves in the wrong side of the drawer being the latest. Good job it’s only going in my garage. Thank you Peter for showing that you are human.
@10MinuteWorkshop
Жыл бұрын
Cheers Gordon! 👍
@johnmenarek8062
Жыл бұрын
It's refreshing to see a professional admit to some mistakes. I just accidently cut a 1.5 inch hole in the wrong place. Fortunalely this time is for a jig.
@10MinuteWorkshop
Жыл бұрын
Easily done! 👍
@romasandmo
Жыл бұрын
I have recently started making a trapezoid-shaped sideboard for my balcony. I have made the bottom and the side and the top. Unfortunately I made the rabbits for the top the same as for the bottom, but they had to be on the other side of top sheet. I do have another. It's not about woodworking. It is just to show my stupidity. I drove to my uncle from my grandmother's place to give him some vegetables from my grandmother. I gave him the vegetables and walked home (because we live close by). After a few hours I had to drive somewhere. I walked outside and I couldn't find my car. I thought someone had stolen it ;DD It took me a few seconds to remember where was my car.
@erickuehne4194
Жыл бұрын
I actually have more respect for you because you're honest about mistakes. It happens to all of us and discussing how you recovered is good.
@10MinuteWorkshop
Жыл бұрын
Thank you!
@brycegardner6171
Жыл бұрын
I've noticed that the longer I go between projects, the more mistakes I make. Thanks for showing your mistakes. It is nice to see your thought process on fixing things. I think dealing with things that go wrong may be the most useful/interesting part of build videos and usually left out.
@UKRussellSmith
Жыл бұрын
People have paid for this content and now you're giving it out for free, sucks to be them!
@10MinuteWorkshop
Жыл бұрын
People who have paid for the content have already had the content, and plenty more since. 👍
Пікірлер: 231