Hi bud,your setup is damn good👍 ..we had more or less the same setup back then,cam was bigger and was stroked to 2.1. . Best bet is to go twin 40s,or 45s. We ran with 40s because we didn't have the funds for 45s then,the carbs is easy to setup if you know the carbs well,but dont give up...lot of potential there bud👌🏾😁good luck on the future mods lol👀😅
@matthewtolmay7160
Жыл бұрын
😂people that think 45s work on a 8v
@ritchiesridemk1vwbuild853
Жыл бұрын
H there. Thanks for liking the build. And supporting my channel.
@hackerofcarsyoutube
Жыл бұрын
I sorce fit and tune webers
@ritchiesridemk1vwbuild853
Жыл бұрын
Hi there. Will keep you in mind thanks.
@joshthomas3285
2 ай бұрын
What did you do with the MaF sensor? Just remove comletely? Any need for tuning after that or just unplugged? Im thinking of changing my standard air filter to a similar bolt on option
@shouldbetrailered9046
3 ай бұрын
Thank you for all the interaction with the community, I have learned so much watching your videos. When you ran the 288 cam did you move to solid lifters? where did you go to get the solid lifters? how was the difficulty setting lash?
@ritchiesridemk1vwbuild853
3 ай бұрын
Hi there. The cylinder head is still hydraulic it's now a 298 cam, where it was a 288 cam. 298 is the biggest you can go on hydraulic. If you want to go bigger like 305 to 320 cam then you change to solid lifters. Thanks for you comment 👍
@claymunsamy
Жыл бұрын
Like the videos.what did you do to make the carb work with this cam
@ritchiesridemk1vwbuild853
Жыл бұрын
Hi there. Sorry late reply don't always get my comments on time. Just air and idle mixture, got it right. Thanks for your comment and support
@claymunsamy
Жыл бұрын
@@ritchiesridemk1vwbuild853 thank you for posting these videos and sharing your knowledge.i wanted to use a 32/36 with a 300 degree cam thought it wouldn't work
@louvendran7273
Жыл бұрын
Ek ken jou frustrasie. Ek is besig met 'n 2001 mk4 VR6 24V 4MOTION. Hoekom het jy nie 'n ABF of VR6 ingesit nie? Is daaide die oorspronklike motor? Jou hele enjin setup klink al veels mooi. Daaidie 298 cam is nie goed in Gauteng se verkeer. Geluk & sterkte met jou bou. Groete van Auckland af. Lekker.
@ritchiesridemk1vwbuild853
Жыл бұрын
Hi there. It's a 1.8 polo block! Everybody is going vr6 and 1.8 20 valve ABF too. Would love to do that but funds right now is a problem but will get there. Thanks for your comment.
@mrchilli8901
Жыл бұрын
Were there any issues with the 288cam?
@ritchiesridemk1vwbuild853
Жыл бұрын
Hi there. No the 288 cam work very well with the weber carburetor set up. Just I wanted a bigger cam and that was the 298 cam.
@cherricobouillon3854
Жыл бұрын
Where did you buy the weber
@cherricobouillon3854
Жыл бұрын
And what modification did you have to do
@ritchiesridemk1vwbuild853
Жыл бұрын
Hi there. Ace motor sports look them up on the internet. They will help you out.
Пікірлер: 21