Excellent. Many thanks for this. Am about to do a brake bleed on a mk7 GTD after having to fit a new rear caliper. Ah the joys of the EPB!! Agree that the Haynes manual says to use the bleed sequence as you have it here. This is a bit odd / novel as I’ve tended to do the brake furthest from the master first, which is a common approach, but I’ll do this new sequence. Agree with the tools and sympathetic approach to the process however, I’ve just got a vacuum bleeder, which I hope will be useful for all sorts of suction jobs. These are not perfect but might have a few more general uses than the pressure system, but I know these are pretty good as you show. I think my rear brakes are the same as you have here and it can be hard to access the nipple. The Haynes manual also recommends bleeding the clutch when doing the brakes and again the details are scant. Great to see the technique (bleed, pump bleed) you used here. Very many thanks!! Is the VCDS ‘brake bleed’ setting only necessary if the master cylinder or ABS module have been drained, do you know?
@fatwalletboy2
Жыл бұрын
I would add 2 things; 1. Always wash your hands before entering the car for the test drive.....you dont want fluid anywhere on the leather touch points or plastics. Or use disposable nitrile gloves. 2. Wear eye protection when you undo the nipples as the fluid could spurt out under the pressure. Did the pedal feel any better after after the fluid change? The old stuff did look bad. Also I take it all the valves are open in the ABS unit for a full fluid clean out?? £3 for those bolt caps is an absolute bargain but wheres the link?
@MauriceNL1
Жыл бұрын
On my A3 8V the fluid was a little bit darker and the pedal feel has gotten a bit better after changing it to DOT5.1
@colinboyle7955
7 ай бұрын
Good explaining everything I love it. Where do you get that print out of instructions to bleed the brake and clutch fluid?
@MonkeyKong21
6 ай бұрын
glad somebody told me that my clutch pedal also uses the brake fluid. I would've guessed it pulled a steel cable
@JamesGadbury
Жыл бұрын
Thanks for the thorough walkthrough. Good stuff, will help loads of people 👍
@volkswizard
Жыл бұрын
Thanks James, helping other is what it is all about 👍🏻
@Sverigebilden
Жыл бұрын
Nice video, is the procedur the same on a left hand drive? Front left, front right ,left back and right back?
@pequod1
Жыл бұрын
I'd consider DOT5.1 as something between OEM and a 'track' fluid a la RBF600, it's ridiculously cheap at GSF now too.
@volkswizard
Жыл бұрын
I will check that out, thanks
@garybocking4541
Жыл бұрын
I had Brembo 5.1 in my Ed30 pedal feel was great.
@roadnwater
23 күн бұрын
Great video. I had a strange situation and wondered if you or anyone had the same. I have a MK7 also and did clutch the same as you did with a pressure bleeder. After bleeding 100 ml from the clutch I had a firm clutch pedal to do the 15 strokes. I then bleed the extra 50 ml and removed the bleeder. Afterwards my pedal went to the floor when I tried to start the car. After pulling it off the floor and stroking numerous times I was able to get a good pedal again. I am puzzled why it happened. Thanks
@volkswizard
23 күн бұрын
Did you just do the clutch as that might be something to do with it if so ?
@roadnwater
23 күн бұрын
I did the brakes first just like the video. I have been driving for a day and clutch feels good so I don't see what happened.
@respectmefu
24 күн бұрын
Thanks for the video! I never found one that explained how to drain the clutch. Quick question, does the manual say you have to have all 4 wheels raised when bleeding? I think it would be much easier for me to do one wheel at a time. I always find it tricky when I try to put my Golf on 4 jack stands.
@volkswizard
24 күн бұрын
In a workshop the car will be raised on a lift and quite often the techs won’t take the wheels off for a BFC. It doesn’t need to be in the air but it helps. I agree it’s tricky on the ground with a jack but not impossible. An axle stand or two helps 👍
@jwester7009
Жыл бұрын
Why are you only bleeding it on one side on the car? Maybe I'm doing it wrong but I always start bleeding the brakes at the wheel furthest away from the brake pedal and I do it on all four corners until I see new clean brake fluid coming out. During the process I keep adding new brake fluid to the reservoir. This process is to make sure all the old fluid is out of the entire system along with water that has been condensing into the system over time
@mda5003
Жыл бұрын
Indeed, most will say to do just that - furthest away first. But, according to the manual for my VW it says left-hand front first then right-hand front followed similarly with the rears. I've no idea why.
@michael6125
Жыл бұрын
He’s only showing us from one side of the car maybe for time convenience as it’s the exact same process for the opposite side on that axle. However he does include a caption stating that the side he’s showing us is after the other side opposite. Also to add he is following the actual manufacturers guide on how to bleed the system so he’s doing exactly what the manufacturers instructed us
@964tractorboy
Жыл бұрын
A job well done. It's easy to see why DIYers aren't too enthused by the task, but there's no excuse for a dealer-maintained car to miss out on such basic work. Hope the track-day goes well!
@Peterv832
11 ай бұрын
Sorry to ask. I am unclear if I should remove the pressure bleeder when doing the clutch fluid? I recently did the brakes. But need to go back to do the clutch and not sure if i should connect the pressure bleeder. Thank you
@conradorodriguez9498
7 ай бұрын
Perfect man! Saved me 35 dollars!
@Jon-mo9ks
10 ай бұрын
If you're only bleeding the clutch, does it matter which wheel you extract from?
@jpgpearson
Жыл бұрын
i use my oil suction kit....which i use for the sump.....first suck old brake fluid out of the reservoir...put fresh brake fluid in.....move your oil suction kit to the nipple and then suck out old fluid until it changes colour making sure you top up the reservoir.
@papillon5537
Жыл бұрын
Mk7 share same brake and clutch fluid? Has to replace them separate way?
@thecomanche1
9 ай бұрын
It says in my VW workshop manual that the bleed sequence must be performed 5 times per calliper. Only if air is in the system though.
@rohrbaughfab
Жыл бұрын
I wonder if since my brake fluid is so dirty it would cause the master cylinder to freak out for the clutch
@wilstw
5 ай бұрын
if you have EPB electronic parking brake..should the EPB be switched off for the bleeding oil at rear brakes
@volkswizard
5 ай бұрын
I think they bleed ok either way as epb is electric, not hydraulic
@stco2426
4 ай бұрын
@@volkswizard Thanks.
@malchowle5618
Жыл бұрын
Bleeding brilliant.. Thank you 👍
@sorbetingle
12 күн бұрын
Stuck nuts...in the past to avoid breaking off a corroded nipple or nut, i have first tried to tighten the nut a tiny amount, that has the affect of unseizing a stuck nut, then undone as normal.
@davidchambers7622
Жыл бұрын
Really enjoyed this Video Andrew, 8 years ago my Porsche dealer quoted me £180, a specialist £90, however I can see the labour involved in this process thanks for sharing 👍
@volkswizard
Жыл бұрын
Thanks David. I am sure some workshops don't do as thorough a job (some don't even do it at all even though they say there have as it's not easy to tell). Some I gather don't take wheels off and do it on ramp, so either they have a better drain hose than me that doesn't drip or they pour a lot of water or they damage paint on inside of wheel :(
@NoName-st6zc
Жыл бұрын
I know those racingline wheels are just your trackwheels and everything but holy crap do these look sheit compared to the pretorias. Just my two cents of course... Apart from that : super useful video explaining something that's done way too rarely on a lot of performance cars where this should be done yearly really. You're absolutely smashing it with your content lately. Keep it up mate!
@Deceptive24
Жыл бұрын
Legend. Such a clean presentation.
@michael6125
Жыл бұрын
Was it me who missed the process of filling the brake system with the new fluid?
@iansaxton8684
Жыл бұрын
Nope, I was just going to state exactly the same?
@volkswizard
Жыл бұрын
The new fluid is in the pressure bleeder, it’s what pushes the old fluid out
@michael6125
Жыл бұрын
@@volkswizard Thank you for this. Just that explanation has taught me something new. Didn’t know it was the new fluid that pushes out the old. Thank you
@e-proyects6691
6 ай бұрын
Where did You find the manuals from vw
@eamol
Жыл бұрын
Good video but I would add one major thing and it's nothing to do with the actual brake fluid change.....Screwing on wheel studs/ bolts with a power tool is the surest way to destroy the threads instantly...
@DrFod
Жыл бұрын
Nothing wrong with that as long as you use a low torque setting and finish tightening with a torque wrench.
@eamol
Жыл бұрын
@@DrFod Everything wrong with it as no one uses a low torque setting to begin with....
@volkswizard
Жыл бұрын
I do as my gun is really old and it doesn't have that much torque, I only use it to thread the bolts into hub to save time, and then I use torque wrench which always needs to tighten them a bit. TBH I used to tighten then way too much before I had an impact gun and a torque wrench like most DIYers probably do as 120nm is not all that much
@simonvazquez6751
Жыл бұрын
Great watch, really detailed 👍. Pertinent for me as I recently had the brakes on my 7.5 GTi bled at Inchcape VW Manchester; They came back feeling spongy and soft. I took it back, they cast an eye over it "fine to us" however still not right. Must buy this bleed kit and do a proper job myself 💪
@volkswizard
Жыл бұрын
Sorry to hear main dealers couldn't do this basic job right. On plus side at least your nipples will be loose :)
@jake15470
Жыл бұрын
Imagine the amount of chips on that mint front bumper after 1 track day let alone of a lorry on motorway! Scary
@volkswizard
Жыл бұрын
The front end is PPF protected, I've done loads of track days and never got a chip even without PPF. Stonechips are annoying but cars are for driving so you just deal with them when they get bad enough
@jake15470
Жыл бұрын
@@volkswizard i have been watching your videos for along time.... fair play buy it and use it for its purpose 👌
@merk8641
4 ай бұрын
What seats are those?
@spills_n_thrills
Жыл бұрын
I watch Golf GTI videos despite owning an Octavia vRS 245 because no one cares about the vRS, even though it's a GTI with 2" longer wheelbase but better day to day practicality (and arguably better interior)
@justinkirkhope8810
8 ай бұрын
Agree, nice car - same with my Superb 280, with the exception of 4wd, much the same on brakes, chassis etc
@robc5955
Жыл бұрын
Thanks good reminder, did I see/hear you say do passenger side first then driver? Also, stupid question I guess but if you have either wet or dry clutch dsg there is no brake fluid operated clutch slave? Thanks
@volkswizard
Жыл бұрын
The order is definitely as follows; front left front right rear left rear right Left or right is as if looking from sat inside the car The video shows front right just because it suited me for filming So start on passenger side front for RHD cars Not a stupid question re clutch as DSG has 2 clutches but none use brake fluid. HTH
@robc5955
Жыл бұрын
@@volkswizard thankyou
@ivanb3303
Жыл бұрын
Very enjoyable and when you reach 50K I trust 75k and beyond is in reach
@chrisp4899
Жыл бұрын
Definitely needed it , have you ever used lanoguard to protect the underbody I'm thinking of doing the rear axle on my polo
@volkswizard
Жыл бұрын
I'll be using the Bilt Hamber protectant now the weather has warmed up
@b4b516
Жыл бұрын
A grade A brake fluid change! unfortunately it’s a dying practice for many no good reasons. I think you should add to these maintenance videos if you haven’t done so before on where the correct locations to jack a VW are. Crushed sills plagued the classics but we can still save the ones to come 😂.
@volkswizard
Жыл бұрын
Good point re jacking points. I don't enjoy jacking any sill but it's better than slipping off some other bit
@joeboycott147
Жыл бұрын
I like the T-shirt, where did you get it from?
@volkswizard
Жыл бұрын
That's very old - I bought it from an official VW Motorsport stall at Rally GB somewhere muddy in Wales in November 2014 I think. Not seen them for sale anywhere since.
@kentowers2802
Жыл бұрын
Andrew Have you tried removing the clutch slave delay valve / dampener? It’s a really good little mod to do while bleeding the clutch
@volkswizard
Жыл бұрын
I haven't removed that yet Ken but having now driven it on track, assuming no side effects, it's got to go as it's awful. Remember it from my first CSS, weirdly my Cupra didn't have it so must have been removed.
@kentowers2802
Жыл бұрын
@@volkswizard I did on my CSS, 7.5 GTI and cupra. Definitely worth doing Also there’s a spring on the pedal which works against the return spring so make the pedal return very slowly Try removing that before the delay valve - it was terrible on my CSS with that spring on the pedal, it just pops off in a few seconds
@philipguacci6452
Жыл бұрын
What about braided brake lines. Race Pads. Wheel bolts rather than nuts, to prevent wheels shearing off. George and Misha at the Nurburgring have done this to their GTI. Or is this to extreme in this case. Cheers from me Andrew.
@volkswizard
Жыл бұрын
Thanks again Philip for the input - braided brake lines are a good idea when upgrading brake hardware so one for future. Same goes for upgraded pads. On a VW you can fit studs to the hub and use bolts to hold wheels on (like on a Ford!) , Racingline do this kit but I feel safer on correctly torqued wheel bolts personally, only benefit really is to make wheel swaps quicker and easier, more important for a racing car where they swap wheels on the grid before races as well as pit stops.
@man1to
Жыл бұрын
You not driving it hard enough then if you say that braided lines are for upgraded brakes ....I've done my first track with my OEM GTi and 3 laps my brakes were gone. Came back at later date with braided lines... motul rbf660 fluid and mintex m155 pads and the difference is night and day. If you going to Nürburgring in the OEM setup your brakes will be gone after a few corners guaranteed!
@davidhaygarth648
Жыл бұрын
Wife hates pumping the pedal...lol
@malcolmscott4150
Жыл бұрын
Now off to the track 🏎🏎🏎🚒 🎯👍
@volkswizard
Жыл бұрын
Pretty much as you typed that, I was indeed setting off. It was an interesting evening that if for sure...........
Пікірлер: 75