You guys are rollin! First start right around the corner!
@Weissworx
Жыл бұрын
Hopefully Friday. Still need a couple of odds and ends to get it all buttoned up.
@leoraffin9071
26 күн бұрын
Hi guys, I didn't found the repaire book, could you please tell me where you found it or send it to me? Have a nice day guys
@Weissworx
26 күн бұрын
Please email us. Weissworx@gmail.com
@timz9406
Жыл бұрын
Hey. Nice build. I am trying to fix one of these. The problem is it was picked up by a forklift before and the forks have broken the oil pan and probably damaged the oil pump. I tried to measure oil pressure and I am getting around 5 psi which is very low compared to ~20 psi. The oil pump looks good and I am not noticing any scratches or broken parts. I also noticed there is small piece of metal that looks like it was broken, but it is behind the oil pump which makes no sense. Do you have any suggestions or reasons why I might of got it broken or if the bottom block skirt can me bend or damaged?
@Weissworx
Жыл бұрын
Hey Tim, how long was the motor sitting before you got it?
@timz9406
Жыл бұрын
@@Weissworx Not sure how long but at least two months I think. However, I probably did find the problem why I am getting low oil pressure. The oil filter housing adapter was broken when the filter was changed and I have already ordered it and will be testing it in a bit. However, a small piece of metal that was missing behind the oil pump is still a mystery to me because it is inside the block, there is nothing that is touching it, and there was no signs of broken metal in the oil pan or anywhere near
@Sleepymk6
Жыл бұрын
My engine block has a hole as well as the upper oil pan , do you guys recommend I just get another engine or is it cheaper to rebuild it ?
@Weissworx
Жыл бұрын
In your situation I would suggest find another motor.
@psiturbo
Жыл бұрын
what happened with the follow up videos of this MK7 rebuild?
@Weissworx
Жыл бұрын
Thanks for the reply. What follow up are you referring to? It was just a rebuild series
@psiturbo
Жыл бұрын
@@Weissworx back in the engine, etc, prime, first crank, any gremlins from the build, final thoughts.... and so on
@Weissworx
Жыл бұрын
@@psiturbo no problem give me a couple days and I can work on that we have some footage of first start
@victorserrano8167
9 ай бұрын
Muy bueno Master y de gran ayuda,pregunta en un motor 1.8tsi,el torque de bancada y bielas cuánto lleva,gracias
@Weissworx
9 ай бұрын
Connecting rod torque. Is 45nm plus 90 degrees
@victorserrano8167
9 ай бұрын
@@Weissworx gracias Master..
@lamerankala8432
11 ай бұрын
Hey.... I am mechanic from Botswana, can you please share with me all VW Engine repair manual you have "especially torque sepcs'' via EMAIL
@Weissworx
11 ай бұрын
Please email me at weissworx@gmail.com
@danwedderburn5550
Жыл бұрын
I would of really like to of listened what you guys had to say, as im just about to attempt a strip & rebuild of one of these. Sadly that stupid music you played prevented me from doing so, so i switched off.
@Weissworx
Жыл бұрын
Thanks for your input. We still have a lot of room for improvement on vlogging If you have any questions. Email us. Weissworx@gmail.com
@Sebas0889
5 ай бұрын
It is possible to share the VW manual. possibly via email or a link, thank you very much in advance
@Weissworx
5 ай бұрын
Shoot us a email weissworx@gmail.com
@Sebas0889
5 ай бұрын
@@Weissworxwill do, thanks
@davidut55
10 ай бұрын
When i honed, like you, the cylinders on my mk2 jetta, old rings had 0.4-0.5mm gap, original engine with 200k km. After some km maybe 1000km, disassembled again, and the rings were over 0.6mm gap. So my honing did worse, the finish wore down the rings in very few km. I am curious how much oil does it burn after this repair.
@Weissworx
10 ай бұрын
We have put almost 20k on the mk7 since the rebuild, oil consumption is around half a qt between oil changes. Well within tolerance. Sold the car to our buddy 4 months ago. It is now his daily and hasn't had a issue. Although after others advice. The last few motors we have built. We slowed the drill down and slowed the strokes, so the cross hatch angle is more with in spec.
@Britcherbrianjr
Жыл бұрын
If I’m going to take advice from someone about a vw, it’s going to be someone with a vw tattoo
@pescatudo
Жыл бұрын
top parabéns
@timz9406
Жыл бұрын
2:45 the piece of metal is missing right under the number 14 which is right on top of the oil pump
@Weissworx
Жыл бұрын
Good Evening Tim, Can you send A picture to our email? Weissworx@gmail.com lets get you squared away!
@timz9406
Жыл бұрын
@@Weissworx yeah. I’ll send you some pictures tomorrow. I also think that due to the low oil pressure the oil filter housing adapter creates, the head-cams run a little bit roughly so I try to run the car as minimal as possible.
Пікірлер: 30