These are so easy to add and definitely add that extra protection needed just put these on my bt50 sp
@VideoShowMeHow
Жыл бұрын
Highly recommend mod this one if you're taking the rig offroad.
@wingzero743
Жыл бұрын
@@VideoShowMeHow yep even for on road as well you never know
@liang2512
8 ай бұрын
Hi Adam. I got some official spec for the tightening torque on that low shock nut. It is 152nm, not 96nm. Cheers
@philiplucky7170
2 жыл бұрын
Thanks Adam going to get them added to my setup
@thegriff9425
2 жыл бұрын
Where do you get all of your ideas from? Nice series. You make many mods look easy. Are you a mechanic? I hope we get to see the car in action on your trips. Looking forward to the updated tow test.
@VideoShowMeHow
2 жыл бұрын
Cheers mate 👍 Def planning on some trip vids yeah
@callumkeys6010
2 жыл бұрын
Are you planing on doing a lift? Munji diff drop?
@VideoShowMeHow
2 жыл бұрын
Yes, and possibly
@liang2512
9 ай бұрын
Hi, can you instal these while the front wheels sits on ramps with suspension loaded? And this install won't affect wheel alignment, right?And the tightening torque you mentioned in your video, is that from manufacture specification?
@VideoShowMeHow
9 ай бұрын
Yeah easy, can install without even removing the wheel if you want.
@liang2512
9 ай бұрын
Dumb question, they don't touch or scrub anything when steering is at full lock right?@@VideoShowMeHow
@liang2512
8 ай бұрын
Hi Adam. 96nm on the shock nut. Was this specification from Munji? Or you have Dmax workshop manual?
@liang2512
Жыл бұрын
I noticed that in order for a rock of something to damage that outer CV boot, it has to get past your tie rod first?
@VideoShowMeHow
2 жыл бұрын
CHECK OUT THE FULL DMAX BUILD SERIES HERE :) -> kzitem.info/door/PLloptHW8MGGhzVQRkJaMUeCIUh5ZEplfB
@4jj3
2 жыл бұрын
Quality vids mate
@VideoShowMeHow
2 жыл бұрын
Cheers bud 👍
@liang2512
Жыл бұрын
Hi, so noticed you have rated recovery point installed without a bull bar. Did you install that yourself? Do you have a video on it?
@VideoShowMeHow
Жыл бұрын
Yep an arb one. Installed video coming soon of a pair I'm replacing it with 👍
@liang2512
Жыл бұрын
@@VideoShowMeHow Thanks. Also, did you install the EGR delete module from Munji 4x4?
@VideoShowMeHow
Жыл бұрын
No, catch can does the job for me
@liang2512
Жыл бұрын
@@VideoShowMeHow What is the part number of your ARB recovery point?
@VideoShowMeHow
Жыл бұрын
Unsure, it's from ARB, left hand side
@MickMcN
2 жыл бұрын
Wasn't aware of this product but am going to order some right now. Thank you.
@VideoShowMeHow
2 жыл бұрын
Be sure to use the code mate, get some bucks off 👍
@liang2512
8 ай бұрын
Hey, did you buy and install these CV guards?
@MickMcN
8 ай бұрын
@liang2512 yes purchased a set for my 2014 model and installed myself.
@liang2512
8 ай бұрын
@@MickMcN Any issues with rubbing or anything? Are you running stock shocks? Did you make any mods or changes for it to fit?
@MickMcN
8 ай бұрын
@liang2512 no issues or rubbing. No modifications required to install and easy installation. Have ARB BP-51 suspension
@shaunmatthews9680
2 жыл бұрын
What’s that Ryobi gun/drill called mate? I’m a Ryobi fan.
@VideoShowMeHow
2 жыл бұрын
Hmm have had it for a while (my @ryobi addiction runs deep haha), just a rattle gun, I think there's a newer one out now
@shaunmatthews9680
2 жыл бұрын
@@VideoShowMeHow I had a drill finally smoke it up and die after 7 years. It was punished too.
@VideoShowMeHow
2 жыл бұрын
@@shaunmatthews9680 mate 10000% go a brushless if you replace, had the same and got a brushless, so much better
@Huda88754
2 жыл бұрын
Impact wrench
@cyclingzero2353
2 жыл бұрын
man this is a good idea except for some reason I only tear inner boots
@941SHINY
2 жыл бұрын
I installed these and the plates had only about 1-2mm clearance from the shocks (factory shocks). Took them off because I wasnt convinced they wouldnt rub against the shock. Emailed Munji about this asking for a refund weeks ago and didnt get a response. Wouldnt recommend.
@VideoShowMeHow
2 жыл бұрын
Hmm have had mine on for a good couple runs now and no rubbing so far? Did you have any rub marks mate? Maybe just bent out a little if concerned?
@941SHINY
2 жыл бұрын
@@VideoShowMeHow They were that close I didnt leave them on to find out. I dont have a vice or anything to bend them easily myself. Do you have a picture of how close yours are?
@VideoShowMeHow
2 жыл бұрын
No don't have a pic, you can kinda see in the vid though
@Huda88754
2 жыл бұрын
While there bolted on you can easily bend them out slightly no need for a vice
@LuckyDuckBoy
2 жыл бұрын
Was just about to order, thanks for the feedback. My concern would be rather than being to close or not bending or not, neither here nor there but not replying to a customer email is more than poor business, refunding is a whole other story. Reply to your customer. Great vid by the way. Love the idea.
Пікірлер: 43