Yes it a screamer that the way I do it the only way to get it done . Ya. As long as you never stop moving it. Very good advice . A pair of digital calipers and also knowing that some piston have a closed end on one side and will never take a clip can save a good amount of frustration and time.💯👍✌️
@thebug4046
3 ай бұрын
Exactly yup!
@GrandPitoVic
3 ай бұрын
Nice, thank you for the info brother.
@thebug4046
3 ай бұрын
No worries
@tonydetwiler2624
3 ай бұрын
be sure to add all the oil when done 👌
@thebug4046
3 ай бұрын
Always 😎
@zanderfowler7995
3 ай бұрын
Front bearing does seal the engine and not the crankshaft.
@zanderfowler7995
3 ай бұрын
Same as the concept of crankcase seals on rc engines.
@thebug4046
3 ай бұрын
I have several engines that run without any seal in the front bearing at all. I have tested The theory years ago and removed the front dust seal and ran the engine in a test stand and it made no difference in it's performance. Or leaking. Lots of airplane engines run with an open front bearing since they are not on the ground getting covered in dirt. I seen some guy on KZitem awhile ago pissed off at some engine manufacturer because his front bearing was leaking on a new engine so he replaced it and it still leaked. How did he test it? Buy plugging the exhaust and carburetor and blowing into the fuel line with the engine under water watching for bubbles. You tune it to rich on the low speed it will leak no matter what you do.
@zanderfowler7995
3 ай бұрын
@@thebug4046 well atleast none ready to run engines need the “dust cover “ for a seal. Seen it and had it happen multiple times haven’t tried the theory on a rtr engine.
@rclife420
3 ай бұрын
Lmfao I love your videos man, some of the shit you say makes me laugh 😂😂😂 Awesome video !! Super informative 💀💨
@thebug4046
3 ай бұрын
Glad you enjoyed it and thanks for watchin!
@420traxxasman
3 ай бұрын
👍👍👍👍👍
@tonydetwiler2624
3 ай бұрын
for me how I remove the front bearing I use a socket piece out of a wrench set that is a little bit bigger than the crankshaft that can hit the front of the bearing and then I hit on it from the back kinda like a dowel pin it's the socket size piece that I use to remove the glow plugs
@thebug4046
3 ай бұрын
You can do it that way as long as you add some heat so it doesn't stress the block And just make sure when you're putting the bearings back in not to hit the inner race
@lottiecooper609
3 ай бұрын
Hello, I'm new to the nitro world and I'm wondering if you might be able to to give me some advice. I have a cen Ctr 5.0 and the carb throttle arm is broken. The grub screw broke off and the arm keeps falling off. I can't find the part so could I possibly use a different carb? Any help would be greatly appreciated. Than k you. Great vids.
@thebug4046
3 ай бұрын
Hey man I'd have to see it. What I can suggest is going on Facebook and looking for the Nitro RC enthusiast group I'm an Admin in there you can post up about sead issues and we can point you in the right direction. I wish I could give you more advice but I don't really know anything about that model to be honest with you
@douglasperry1226
3 ай бұрын
Thanks for the tips! 🤘🏼Don’t use map gas you will melt it! Lmfao!
@thebug4046
3 ай бұрын
Hey no worries! I have for years it's all about heat control 😉
@douglasperry1226
3 ай бұрын
@@thebug4046 Like I said before most folks have no Mechanical experience. Was just pointing that out for you. ✌🏼👊🏼 😂 No worries is absolutely correct! I’m totally old school and love fuel aspirated rigs ! 🍻
@thebug4046
3 ай бұрын
@@douglasperry1226 absolutely man! I'm gunna try some odd ball stuff soon if all goes to plan
@douglasperry1226
3 ай бұрын
@@thebug4046 10-4 do it!
@andrewgates9518
3 ай бұрын
Can we all take 5 think how much hobbie time an cash thebug saves us viewers, I would 👍twice if I could ❤ ya bug, got your vids saved anytime I need advice
@thebug4046
3 ай бұрын
Hey man thank you very much for the kind words I really appreciate it and I'm glad that my videos are helping people that's why put them up since there's so much poor advice out there and things that aren't done properly which screw with people and cost a money time and patience. 💯😎🍻
@HillbillyNitroRC-qs9dy
3 ай бұрын
What bearings do you use?
@thebug4046
3 ай бұрын
Acre usually
@mikehollingsworth3814
2 ай бұрын
Yo bug, quick question... As I was putting together my engine I noticed that my clutch bearings were a lil stiff/tight but I put some oil in them and now they seem fine. Do you think they will be ok?
@thebug4046
2 ай бұрын
Replacement is a better option since they will do the same thing after a short amount of time and the oil will come out and make the clutch slip
Пікірлер: 30