Excellent information 👌 👏. Thank you very much!!!!
@seth3209
Жыл бұрын
I have a Cousin with a 05 VW Passat 1.8T with Communications issues… I’ll try that when I get to SD next month! Thank you, Sir!
@edogblaze7219
Жыл бұрын
Yes my OBD port doesn't work on my Mercedes a180 2014. I'm starting to think that that it might be the battery .I don't know how low it goes before it shuts you out of all operations on the ignition and ESL and ignition barrel no response..with a new battery it might jump in to life hey???great video
@hotshotgarage271
Жыл бұрын
I have power going to everything but my scanner tells me there’s no information or it’s not connected any tips?
@Waynetoosaucey
Жыл бұрын
12v wire fault, check the fuse for power, if it was it.
@justmyopinion8395
7 ай бұрын
Im having the same issue with power and no connection and I watched every video available on YT. Every video is saying check to voltage and fuse. However if it’s the voltage or fuse why does the scanner still power up?
@e3xPnico21
7 ай бұрын
Same issue here
@yxilly
7 ай бұрын
Any luck? I got the same problem
@itsonlyafl3shwound
6 ай бұрын
Because we all got ripped off and bought a crappy scanner. Our vehicles are fine it's the youcanic scanner that doesn't work and gives us all the same message. Absolute waste of money.
@cdizz7782
9 ай бұрын
I have power on obd2 scanner however it says no communication or unable to link.. any suggestions? 2006 Silverado
@MrMugenwii
8 ай бұрын
did u figure it out. like my comment so i can see response. thanks!
@cdizz7782
8 ай бұрын
@@MrMugenwii no I haven't really tried though. I'm thinking it could be a bad ground but I don't know for sure especially because I have power just no communication. I would assume that no ground would lead to no power. I have checked the connector all the openings are tight so it not a lose connection either. I guess it's a common problem let me know if you come up with anything.
@jonnilynnsavard6789
7 ай бұрын
Did you end up finding the issue? I have power to mine but no communication as well. I’m thinking it’s the ECU
@asaphector
5 ай бұрын
@@jonnilynnsavard6789 yeah sounds like ecu did you replace it ?
@gregorykowalski6832
2 күн бұрын
2000 f250 fuse was replaced scanner powers up but cant pull data
@paho188_iron_phill4
29 күн бұрын
i can connect to my engine with scaner but cant connect to central elec. i have no power on can low/high or K line V is jumping betwen 0.5V and 3V resistor is 60ohm
@anthonmyl
Жыл бұрын
Grazie!!!
@AUTOSARTID
Жыл бұрын
When you buzz pin no 4 & 5 where's should i put negative on multi tester. Cz when i clamp on body shell there's no beep.
@Dr.Stacker
Жыл бұрын
Scratch off some of the paint and primer, and try again.
@AUTOSARTID
Жыл бұрын
@@Dr.Stacker got it thanks!
@user-hr5dc4ly3q
3 ай бұрын
How make obd car port fast tester because one time i test 1990 nissan patrol swap with lumina v8 engine but all OBD wires was wrong and my expensive scantol makes smoke 😢 so my advice dont use scantol before test obd all pin powers and ask car owners is the engine swaped
@YOUCANIC
3 ай бұрын
Thanks for reaching out and sharing your advice! We at Youcanic aim to empower car owners with resources such as guides, our powerful Youcanic scanner and even factory repair manuals to tackle such issues. This ensures you're confident and safe when doing car maintenance. Visit us at www.youcanic.com for any assistance or information. We're here to support you on your car ownership journey!
@joshuaturner-qe6rk
Жыл бұрын
My obd2 port is only reading 3 volts why??
@itsonlyafl3shwound
6 ай бұрын
Waste of money. Works on diagnostic but when you go to maintenance to try and reset/ fix any codes it just says no communication. Seems like many people get this. It's not your car it's the junk scanner. Go elsewhere don't waste your money.
@YOUCANIC
6 ай бұрын
We appreciate your feedback. At YOUCANIC, we're dedicated to helping car owners diagnose and repair their vehicles confidently. We provide an array of resources, including our YOUCANIC Full System Scanner, which is engineered to diagnose car issues comprehensively. You can learn more here: www.youcanic.com/scanner If you're facing communication issues when resetting codes, we recommend you to ask questions on our platform for assistance: www.youcanic.com. Your trust in YOUCANIC is greatly valued - we're here to make car repairs accessible and understandable for you.
@mrashad219
Ай бұрын
My stabilitrack light comes on when I hook up diagnostic tool to the OBD 2
Пікірлер: 33