Great video, I noticed my oil pan gasket was leaking a bit during my last oil change, I'll definitely be doing this job very soon
@chrispeters4405
2 жыл бұрын
without having to lift the engine! you have to do the main bearings
@yeddyidk9707
2 жыл бұрын
Thank you sir. Saved me 3,000
@omar__0rtega409
3 жыл бұрын
You mentioned that it was struggling to accelerate was this really the solution to that my pressure has been dropping as well
@jesusalvarezsayula1784
3 жыл бұрын
Yes it worked for me, i think that rock blocking the screen was the actual problem lol. But just went ahead and changed the pump anyway
@jesusalvarezsayula1784
3 жыл бұрын
Also my oil pressure sensor was burnt up pretty bad so i changed that too.
@mogeking56
3 жыл бұрын
She said take the dipstick out before having the baby. That makes sense to me 😵💫🤓
@tc50cal888
2 жыл бұрын
Great video! Thanks for sharing!👍
@TheSmoothGrind
3 жыл бұрын
Nice video. I am going to change my oil pan in my 2001 ram plow truck next week. The pan rusted out and is pissing oil. I was hoping to do it in spring/summer with nice weather, but I can't wait any longer and still use the truck. I appreciate your info on bolt sizing and your video of you dropping the pan. I was worried it wouldn't clear the cross member, but looks like you got it out of there fairly easily. Thanks again!!!!
@jesusalvarezsayula1784
3 жыл бұрын
Thank you ! Its not too bad, just sucks that theres very little room to workaround. Hope it helps you out thanks for watching👍🏼👍🏼
@tylerknight4723
2 жыл бұрын
Hell wait till summer I'd use JB weld all over the bottom of the oil pan basically create a shell that way you can make it to at least spring just don't go near the oil pan bolts
@TheSmoothGrind
2 жыл бұрын
@@tylerknight4723 Might of been able to do that, but meh, I don't like rigging stuff. I swapped it out last January in like 10 degree weather on my driveway. It wasn't so bad.
@danielwillover450
3 жыл бұрын
You should do a video on how to put it back on but changing the rear main seal also
@jesusalvarezsayula1784
3 жыл бұрын
I will look into it !
@donking8662
3 жыл бұрын
@@jesusalvarezsayula1784 did you figure out how to put rear main seal in ??
@jesusalvarezsayula1784
3 жыл бұрын
@@donking8662 hey man, no i havent actually its been sitting for a while im in the process of painting it but if i do end up doing the seal i will post a video
@donking8662
3 жыл бұрын
10 4 that will be a big help for me , im finna have to do the seal on my 01 dodge 4x4
@barrybennett1292
2 жыл бұрын
If you have fluctuating oil pressure, it also pays to check your pressure sensor and connector before dropping the pan.
@martinhudson2657
4 жыл бұрын
Look like you have a broken engine mount bolt too, looks like it, key word
@jesusalvarezsayula1784
4 жыл бұрын
What minute did you see it at, i should probably check it out!
@tomhutchins1046
2 жыл бұрын
Or a tooth off a nylon timing gear. The oil pressure going up and down was probably the sender
@shawnb8234
4 жыл бұрын
I have the same truck did u have to Jack up the motor to get the oil Pan out
@jesusalvarezsayula1784
4 жыл бұрын
Sorry bout the late reply, yes i did my truck is lowered 3 inches up front
@jesusalvarezsayula1784
4 жыл бұрын
@the Accountant the lowering? I bought it like that but i believe its a 3 inch lowering spring and djm control arms or calmax.
@Rchan925
3 жыл бұрын
@@jesusalvarezsayula1784 I'm wondering the same question. Jesus did you have to jack up the engine? Not is ur truck lowered
@jesusalvarezsayula1784
3 жыл бұрын
@@Rchan925 fortunately no i didnt have to lift the engine up, i was able to get it out witj engine in place, mine is a 1994 5.9, 2wd..46rh trans if that helps.
@Rchan925
3 жыл бұрын
@@jesusalvarezsayula1784 thank you It does
@malcolmveganlifewoods1399
2 жыл бұрын
I have the 1994 dodge ram B250 trying to remove the oil pan is a pain, not enough clearance between the outer bottom oil pan and the cross member I haven't t removed the oil dipstick maybe that's what is holding the oil pan. I'm not for sure, I will try again the next day and give it a go any tips or suggestions to help pull this thing out?
@tomhutchins1046
2 жыл бұрын
Looks like a chewed up valve seal. Umbrella type. Some are white plastic
@martinhudson2657
4 жыл бұрын
When your taking about your gasket oil pan gasket I seen it, check video the part that unexplaining about the gasket
@billjunking_fool5549
2 жыл бұрын
I am guessing that's part of a timing gear
@flukesofevolution5693
4 жыл бұрын
I have a 1995 ram van 2500. 5.9 engine. I was told I had a bad oilpan gasket and it was easy to replace so I bought all the stuff I needed and tried to do it myself. Didn't know I had to lift the engine. I got the pan detached but I can't remove it. There's too many obstructions. I removed the starter and the brackets holding the transmission to the engine. The pan won't drop down. Im not a auto mechanic. Just your average DIY cat. Does anyone have any advice? I'd sure appreciate it. Thanks.
@stanleygardner146
4 жыл бұрын
Jack the engine up with wood underneath the oil pan. Unscrew the motor mounts and jack up and put wood under the motor mounts
@johnfitbyfaithnet
3 жыл бұрын
@@stanleygardner146 great tip
@martinvalencia6141
3 жыл бұрын
Did your truck get fixed with the pump and pickup replacement?
@jesusalvarezsayula1784
3 жыл бұрын
Yeah it works good now, i also had a burnt up oil pressure switch that i changed out too.
@keithsims86
3 жыл бұрын
@@jesusalvarezsayula1784 Did you prime the pump?
@Namelesshero-e8k
Жыл бұрын
@@keithsims86 how do you do that
@1141Nan
3 жыл бұрын
Is this a 2wd or 4x4?
@jesusalvarezsayula1784
3 жыл бұрын
Its a 2wd
@dirtyboy8336
8 ай бұрын
I just don’t Understand why Most of Guys that Fix on vehicles never wear protection glasses so any dirt or fluids dropping in their eyes
@martinhudson2657
4 жыл бұрын
As soon I looked at your video
@jesusalvarezsayula1784
4 жыл бұрын
Ill take a look at it, thanks 🤙
@matthewdougan3816
3 жыл бұрын
It was a pain in the ass to put in
@jesusalvarezsayula1784
3 жыл бұрын
It really is. It helps to use zip tied in a few bolt holes to hold the gasket in place
@12569781cdn
3 жыл бұрын
@@jesusalvarezsayula1784 really appreciate the zip tie idea!
@luckylascala7572
2 жыл бұрын
You said V8?
@jesusalvarezsayula1784
2 жыл бұрын
Yes, v8 5.9
@luckylascala7572
2 жыл бұрын
@@jesusalvarezsayula1784 I thought come inside a straight 6
Пікірлер: 49