Hey Brandt.....you also need to press the RST button once you are finished with all the changes. I didn't and it did not save the changes. Just a heads up! 😎
@ChipperoniD
3 жыл бұрын
Thanks man, you've really helped me along the way. Truly appreciate you taking the time to cut a trail for us coming up behind you.
@BeardedBuildsCo
3 жыл бұрын
You’re welcome! Glad I could help!
@michaelsfabwork2985
2 жыл бұрын
Just got my chiller today so im going to try and get it set up. I will be following your video for the set up. Thank you. Take care and stay safe. I subscribed as well.
@tylerwiltsey6447
2 жыл бұрын
Couldn’t have setup my laser without your videos 👍
@Rover0010
10 ай бұрын
Thanks, don't know why OmTech doesn't relay this info on their web site, but your video was great and I hope that resolves my E3 Error.
@timetempest
3 жыл бұрын
Thank you for a quick and concise guide! Straight to the info I needed. 🙌🏻🙌🏻🙌🏻
@dgoddard
2 ай бұрын
Dude, you rock. I've been messing with this thin (newer CW-5200) for the last hour. The Chinese make great products, but they really need to hire someone who speaks English to write their manuals. LOL Thanks, bud.
@AceDaPig
Жыл бұрын
I found that I needed to set F0 to the water temp I wanted, because the changes made to F8 and F9 I believe are for the automatic mode. But we switched F3 for the control mode to be constant instead. I was finding that my water temp was not going to the settings from F8 and F9 until I made the change to F0 to be 18 instead
@SkullyWoodMetal
3 жыл бұрын
Thanks for the help and clarification. I have the 5200.
@BeardedBuildsCo
3 жыл бұрын
You’re welcome! Glad I could help!
@khertler
3 жыл бұрын
Can you describe a little more what these two settings actually do? I just received my first laser a couple days ago and I’m trying to understand as much as possible. Thanks!
@BeardedBuildsCo
3 жыл бұрын
Inteligente mode matched the ambient temperature and constant temp mode will keep the water cooled to the temp that you set.
@wrightswoodworks5199
3 жыл бұрын
Thanks man... super helpful!
@j-wings
Жыл бұрын
Note: for the CW-5202 I just purchased this week, this still works, but to activate the advanced control mode, you have to push the up arrow SLIGHTLY before you push the set button.
@michaelmargherio1716
2 жыл бұрын
Excellent to the point video, Thank you!
@jhdesignshouston1469
Жыл бұрын
Thank you again!
@creationsbyjni3858
3 ай бұрын
🎉🎉🎉🎉 love it thank you
@raysalvador7573
2 ай бұрын
Not working for me. I dont get the “F” displayed. Do I need to disconnect my hoses?
@Urmo940
Жыл бұрын
My 5200 Chiller temp keeps going up even in constant mode set at 16. I don't know what to do and I am never going to get this thing up and running if I keep running into issues :( I love your videos though!
@mariobrown9812
2 жыл бұрын
I just recently purchased the 5202 & it feels like there is water already inside it. Mind you, I purchased it brand new directly from OMtech. Is this normal? I can see & hear it. I just don’t want it to not be distilled or any other fluid not regulated for this device.
@smattt
8 ай бұрын
I live up north and my machine is in the garage. Guessing I'll need to use antifreeze mixed in with the water - what ratio would you recommend? I have the CW-5200.
@BeardedBuildsCo
8 ай бұрын
100% rv antifreeze
@PlanetrightPro
2 жыл бұрын
Hi, just wondering after I've set it up for 19 degrees on constant, the compressor doesnt shut off when it hits 19 degrees? Does it run continuously in constant temp mode. Thx
@chrisbrophy2818
Жыл бұрын
Setting up my CW5202 chiller with my new Omtech MF2028 60w. Connected lines(no kinks)to inlet/outlet Set A...filled to proper level and turned unit on. UNIT ALARM will not shut off and keeps beeping. Tube filled and do not see leaks. Do I need to set constant temp before alarm shuts off or can there be another reason for alarm. Appreciate any insight.
@BeardedBuildsCo
Жыл бұрын
Have you made sure that you have your connections correct? Chiller outlet ➡️ laser inlet Laser outlet ➡️ chiller inlet
@WestCoastPrepperRN
Жыл бұрын
If you have the 5202, you have to put a short tube on the ports you aren't using if you are just running 1 laser...ie: a short piece of tubing running from the input to the output ports on the back of the chiller as a loop, then run the lines like normal to the laser on the other input/output ports...
@deeplyrootedone
2 жыл бұрын
I've followed your instructions, which are great by the way. I even repeated the steps thinking that turning off the power strip its connected to, caused it to revert back to the default settings. However, my chiller still goes above the max temp. Is this normal?
@BeardedBuildsCo
2 жыл бұрын
At the end you need to press RST to finalize all the settings not SET
@absolom7691
3 жыл бұрын
Thank you!!
@andyvillegas487
2 жыл бұрын
My chiller when set and up are pressed it goes to -2, 0 never comes up. Is there another combo or am I pressing a third button?
@1010tesla
3 жыл бұрын
remember, if you live in a hot humid area a setting too low could cause condensation to form on your tube and potentially arc from the high voltage connection. ask me how I know...
@angeladelreal9046
3 жыл бұрын
I live in Texas you just described my weather what do you do about that?
@1010tesla
3 жыл бұрын
@@angeladelreal9046 the chillers have a mode where they regulate the water temp relative to the ambient temp. you will have to read that hard to understand chinese manual and work out what temp is right for your conditions while still keeping the tube at a safe temp. I live in oklahoma so we have similar conditions.
@randytaillon3818
3 жыл бұрын
I noticed you seem to have defeated that annoying chirping. Can you share how that was accomplished.
@BeardedBuildsCo
3 жыл бұрын
Right here… kzitem.info/news/bejne/tmyCzqmtqZOpdIo
@randytaillon3818
3 жыл бұрын
@@BeardedBuildsCo I saw that one already. I'm talking about the chirp from the chiller alarm.
@BeardedBuildsCo
3 жыл бұрын
A chirp from the chiller is not normal operation. Are you getting normal flow? Does it seem like the water is pulsing?
@randytaillon3818
3 жыл бұрын
@@BeardedBuildsCo I assumed it was announcing a swing in temp like the controller for my AC mains heatbed controller on my CR-10 with 750w bed heater. I followed the tube routing inside the machine and found a kink in the line at the Y. The kink was caused by a short run of tube that was actually too long. Chirp eliminated. Thanks for putting me on the right path.
@BeardedBuildsCo
3 жыл бұрын
Awesome! Glad you got it figured out!
@RussellRay
3 жыл бұрын
How come in the manual on number 6 it says press ret to save your changes and then exit? It says pressing set will not save your changes
@phototec
2 жыл бұрын
Yep, the video instructions are NOT correct (the video should be updated).....IMHO
@outragedpi3
2 жыл бұрын
I sat holding the two buttons for over a minute and 0 doesn't come up. Is my unit defective? Is there a reset?
@BeardedBuildsCo
2 жыл бұрын
Did you hold the correct two of the four buttons?
@angeladelreal9046
3 жыл бұрын
my water tube is building up condensation. what can I do to change this
@CHS10901
3 жыл бұрын
The easies would be to get some foam insulation like what is used for insulating copper water pipes in your house. You should be able to get that from Home Depot or any other home store or hardware store.
@albertdrew7235
Жыл бұрын
Hey Jeff thanks for the info. However when I press both Set & Reset I cannot get it to go to "0".. It starts to count down in two places. Thanks
@fellowshipsquareseniorlivi1289
2 жыл бұрын
tried it, no luck. It always showed -0.0 with not just one 0. I unplugged unit and tried again no luck
@SnailTrail4x4
2 жыл бұрын
@beardedbuildsco I am having the same issue, any idea?
@armydoggscreations8195
2 жыл бұрын
Same here
@armydoggscreations8195
2 жыл бұрын
I figured it out, when you get 0.0, go up to 0.8 hit set then you can follow the steps
@0711dogs
2 жыл бұрын
My F numbers are not coming up. What am I doing wrong?
@gregoryfletcher7170
Жыл бұрын
did you ever figure it out ? having same problem
@jackbrady7
9 ай бұрын
Me Too...@@gregoryfletcher7170
@tiffsdecorandmore
3 жыл бұрын
I press and hold and nothing happens
@1haggler
Жыл бұрын
Would like to know is the Constant Temp Mode necessary? Would running out of box suffice? Just trying to understand the difference, like is it more useful in regions that have extreme temps? Please advise Thank you
@thogg4
3 жыл бұрын
What settings can I use to keep my drinks cold while using the laser?
@frekuramusicyoutubechannel2961
Жыл бұрын
Need to press RST to save settings to finish
@BeardedBuildsCo
Жыл бұрын
Yep, that is clarified in the description
@sergiorodriguez1291
2 жыл бұрын
Literally me pressing the up arrow and set doesn’t do anything
@BeardedBuildsCo
2 жыл бұрын
What does your manual say to do?
@alicelaser7542
2 жыл бұрын
This is a knock off, not a genuine S&A 5200 chiller…
Пікірлер: 63