V10Absolute purchased July 2018. Fluffy Head stopped spinning. As there was nothing obvious stopping it from working assumed it was a motor problem and as a replacement was going to cost $A170+ which I was not prepared to pay decided to let an electrician friend have a play. Using a meter thingy he ascertained one wire not connecting (no power) so started to disassemble (as above but did not actually have to remove the motor itself) which led to removing purple concertina tube and red buttons (challenge in itself). The broken black wire was in a slotted section in the round grey plastic tube which surrounds the purple concertina hose. Long story short....as he could not get access to do a complete re-wire, he joined the broken wire, drilled a hole above the red button on the backside and another in the clear plastic bracket that holds the brush head onto the part with the concertina hose and pulled both wires through and although I now have the wiring on the outside the whole outfit is working as new . I'd post photos if I could.
@DadsDo_eMTB
Жыл бұрын
Thank you very much for the video. The fluffy head didn’t spin around so I had to take it completely apart to get all the hair out and twine. Now it works perfectly and you save me £65
@choppertbs
3 жыл бұрын
This video saved me!! Disassembled to clean but unable to assemble back! Thanks for this step by step video!
@OpenMeUpTec
3 жыл бұрын
thanks for your support
@KriptoSeriak
5 ай бұрын
Helped me a lot with your clear instructions, including showing where the screw or piece will be placed. Thank you for this! Cleaning made the battery last longer too.
@OpenMeUpTec
5 ай бұрын
thanks for your support
@moderntouchfurniture
Жыл бұрын
Wow this video really helped me after I took the head apart and couldn't figure out how to put it back together, thank you!
@sedonaj1
6 ай бұрын
Haha! Me too!
@typeinyourname
11 ай бұрын
Straight to the point, clear and simple. Thank you, mate!
@seanward5211
5 жыл бұрын
Your attention to the details is very helpful. Very well done. Thank you!
@OpenMeUpTec
5 жыл бұрын
thanks for your support
@TjB2653
Жыл бұрын
Thank you soooo much for this! I've just spent half an hour removing the hair which had become tightly wrapped around the spindle on the rear, small roller with an old (blunt) steak knife. I wish I'd thought to look on KZitem first! Having followed your instructions and removed the side bit and the fluffy head, I was horrified to see how much hair had wrapped itself around the spindle. Now that I've removed it, I can try and clean the fluffy head itself with a bit of detergent and an old toothbrush. Thanks again!
@Monoperty
4 жыл бұрын
Thank you 🙏 I’ve been able to fix a blockage after watching this 👍
@OpenMeUpTec
4 жыл бұрын
thanks for your support
@OpenMeUpTec
4 жыл бұрын
thanks for your support
@sandragipsy
2 жыл бұрын
The most detailed and thoughtful, though clear how-to. Was very helpfull. Thank you so much.
@OpenMeUpTec
2 жыл бұрын
thanks for your support
@davidc2072
Жыл бұрын
Thank you! Mine doesn’t have the rear roller, but I simply needed to replace the big one and don’t have a coin slot on the side. All the videos showed coin slot on the side and none were like yours explaining the fact the slot on bottom needs to be vertical, and how to pivot the side piece with the arrow. Thanks!
@OpenMeUpTec
Жыл бұрын
thanks for your support
@DelwinHamm
Жыл бұрын
Excellent! This was very helpful although I simply used the first step to open and clean it! Thank you!👍
@ongdanny1843
4 жыл бұрын
Thank you! I had a crack at the grove of the motor, watched your teardown and managed to taped it back. roller head working once again. Cheers!
@OpenMeUpTec
4 жыл бұрын
thanks for your support. good to know i was able to hel you
@CsabiMolnar85
Жыл бұрын
Another awesome tutorial! Watching you video saved me a lot of headache. It was very easy to clean my motorhead thanks to your great step by step video guide. Much appreciated 👍!
@OpenMeUpTec
Жыл бұрын
thanks for your suppport
@renegraff795
4 жыл бұрын
Thank you! Was struggling with the cover on the motor side. Ended at your video browsing YT for guidance and this was very helpful!
@OpenMeUpTec
4 жыл бұрын
thanks for your support
@donglobal
3 жыл бұрын
Thanks for sharing and your patience in dissembling and putting back together.
@OpenMeUpTec
3 жыл бұрын
thanks for support
@xiomuki9228
2 жыл бұрын
İ think some models doesnt have a back roller it just has weels first you need to take apart the four screws at the bottom than the tiny screw in the left if you are looking from the back (there is no screw under the label) then turn it upside down and pull the part that has big weels it will come up a little And pull from the part that is in the spot of the back roller it will come off and its same from there
@OpenMeUpTec
2 жыл бұрын
yes that is true depends on how new or old your head unit is. this is the newer model but should give you an idea where to look for the screws
@marcoegging2348
4 жыл бұрын
Your tear-down video was well done showing clearly both the disassembly, and refitting considerations, at each stage. Great job !! PS. See, I had a problem like Jl Wel2 (1-Jul-2020)
@OpenMeUpTec
4 жыл бұрын
thanks for your support
@patbarry2123
4 жыл бұрын
Excellent “how to” - best available!!!
@OpenMeUpTec
4 жыл бұрын
thanks for your support
@sandlinjames
2 жыл бұрын
Absolutely amazing. Perfect level of detail. Thank you!!!
@OpenMeUpTec
2 жыл бұрын
thanks for your support
@AlexanderTheGrateful
3 жыл бұрын
Farout I thought I was watching myself there, I do all my work in those pharmacy tote lids as well lol
@OpenMeUpTec
3 жыл бұрын
thanks for your support
@judybridges8796
8 ай бұрын
Thank you, very clear and organized instructional video😊
@Necronox24
2 жыл бұрын
Have a V12 absolute. I HATE this stupid design. If you have someone in the house that sheds long hair, this machine is a PAIN to clean and untangle. You need a torx screwdriver to clean this machine. I have switched to a Roborock vacuum machine with a dust bag assembly in the docking station. My life has been so much better since. I just need a cloth to wipe the hard to reach areas once in awhile and I'm done. Maintenance of the robo-vacuum is basically tool-less. These machines are supposed to make your life easier... Not harder.
@59isfine
2 жыл бұрын
Thanks for the video. I had a screw stuck in the head of my v11.
@kanittawiprakasit3738
7 ай бұрын
Thanks! Simple and clear. Much appreciated 🙏🙏
@kirill-1983
3 жыл бұрын
Thank's a lot for this video. Simple and informative!
@OpenMeUpTec
3 жыл бұрын
thanks for your support
@Adventure.AS.25
3 жыл бұрын
Good video. I've ordered some Torx drivers to do the disassembly.
@OpenMeUpTec
3 жыл бұрын
good luck
@jimdow6470
Жыл бұрын
Thank you for the video. It does not however, show how to clean the tiny plastic rollers on each side, between the rollers. These become clogged almost immediately, with dog hair, and become immobile, causing the head to drag across the floor. Any ideas?
@OpenMeUpTec
Жыл бұрын
can you watch the video and show me where i can see the roller? i have a newer version of the video on my channel which should have it
@maibeppu9
9 ай бұрын
Great video but you didnt take apart the motor and show how to resolve internal problems with the torque gear wheels.
@paulbeharrell
3 жыл бұрын
Thank you very much for this excellent how-to!
@OpenMeUpTec
3 жыл бұрын
thanks for your support
@abrahamvargas3693
3 жыл бұрын
Thank you I had a hard time opening it
@OpenMeUpTec
3 жыл бұрын
thanks for your support
@KXYZ32
4 жыл бұрын
How to disassemble those small wheels...hair stuck in there we need to disassemble and clean.
@noodlefu_
4 жыл бұрын
I just took a knife and tried to pry it all out. Full of the girlfriends hair...
@OpenMeUpTec
4 жыл бұрын
i have a new video and in that one it shows you how to remove the wheels
@OpenMeUpTec
4 жыл бұрын
@@noodlefu_ i have a new video and in that one it shows you how to remove the wheels
@gruskoda8511
4 жыл бұрын
@@noodlefu_ were you able to successfully pry it out? I fiddled with it and almost ended up breaking the wheel and axle
@edelyntong590
3 жыл бұрын
@@OpenMeUpTec May I know which video is it?
@msmelohamid1469
2 жыл бұрын
This is very helpful.. Thank you and truly appreciate your effort! 👍🏼Can I ask whether can we wash the roller..?
@OpenMeUpTec
2 жыл бұрын
yes you can wash the roller by hand. the garden hose is a good solution. otherwise soak it in soapy water and wash
@msmelohamid1469
2 жыл бұрын
@@OpenMeUpTec thank you for your prompt response sir. Will proceed as per your advise. Have a good day 👍🏼
@djispro4272
5 ай бұрын
Great tutorial! Thanks!
@jlwel2616
4 жыл бұрын
I had an issue with my roller not spinning. I took it apart, cleaned it and then turned on the Dyson without putting the roller on to see what the motor was doing. The cross looking part at the end of the motor would rotate couple times and then stops spinning. Do you think there is a repair for that? Should it be rotating the entire time?
@OpenMeUpTec
4 жыл бұрын
so at 8.00 in the video thats the motor. it should be spinning as long as the trigger is press. i recommend you to disassemble everything and just test the motor itself. if it is not working it is most likely dead. it is a simple product therefore i dont beliebe you can fix a dead motor.
@jlwel2616
4 жыл бұрын
Thanks!
@marcoegging2348
4 жыл бұрын
@@OpenMeUpTec + @JI Wel2 .. My soft roller is not spinning when connected to the vacuum unit (V6 absolute) .. i tried the vacuum unit with other roller attachments and they all spin OK .. so its not a problem with vacuum battery (1month old), connectors, or shafts .. So I did the "open me up" teardown too, but found only small clumps of dust fibres to clear - nothing significant .. While the motor was isolated (as per video 10:02), I held the roller motor wire terminals directly onto (kitchen knives inserted into) slots of standalone Dyson battery - the motor spins for a whole second after pressing the battery switch button .. Also I tested and confirmed connectivity from the roller motor terminals back to the power pins of the roller's shaft .. Overall I could not find a problem aspect .. I just reassembled it carefully and re-tested, but it still behaves the same as before the teardown .. ie the vacuum is sucking but roller is not responding to battery. Any ideas ??
@OpenMeUpTec
4 жыл бұрын
@@marcoegging2348 go back and do everything till 5.55 and testing the roller there by placing it back in the vacuum. the motor should spin if not then you have a motor issue
@marcoegging2348
4 жыл бұрын
@@OpenMeUpTec Thanks, Yes - it must be a motor issue of this soft roller. When the power trigger is pressed, motor spindle may do quarter or half turn only; switch off and on, and then maybe get another quarter turn if assisted. Internet has motor assemblies for US48 plus shipping which I will skip, since I can use our brush attachment as 2nd best instead. I would consider getting just a motor, but I could not see how to open the motor assembly casing to access it. Cheers, M
@johnmillett2831
3 жыл бұрын
Great video. Found TONS of hair and fuzz.
@OpenMeUpTec
3 жыл бұрын
thanks for your support
@witthoftah
2 жыл бұрын
I can see some wear on the padding on the sides. How can you maintain, clean, and/or replace those pieces?
@martiangod
3 жыл бұрын
What size torx please ? Great video 😀
@OpenMeUpTec
3 жыл бұрын
you need 2 different types and a phillips. i believe it is t6 or t8 and you need a bigger torx which is like t10
@toodle171
3 жыл бұрын
like button smashed! Thanks
@OpenMeUpTec
3 жыл бұрын
thanks for your support
@theozhang5327
2 жыл бұрын
I have a DC72, I would like to ask whether this way can fix the head stopped spinning problem?
@jamesisonfire4925
Жыл бұрын
Thank you! This really helped me out
@Mr.LarryLar
2 жыл бұрын
Done deep clean mine. Great & helpful video. Love the artwork of Dyson. The only thing now is the small roller got hair stuck on one side(left side - my view while watch this vid). Is there a way for me to open that roller as well? Can't find any visible screw.
@OpenMeUpTec
2 жыл бұрын
can you watch the video and tell me at what time i can see the roller you are asking about
@Mr.LarryLar
2 жыл бұрын
@@OpenMeUpTec 2:55. The smooth/small roller
@OpenMeUpTec
2 жыл бұрын
@@Mr.LarryLar wathc my video on the OPEN ME UP! Dyson V11 and V10 High Torque Head Disassembly and Clean at 21:55
@Mr.LarryLar
2 жыл бұрын
@@OpenMeUpTec Sorry not the small roller but the soft roller(In this vid - the blue roller)
@theanimaster
2 жыл бұрын
The white wire on mine broke where the head swivels left-right. How do I pop off that red clip so I can run a new wire??
@OpenMeUpTec
2 жыл бұрын
there are screw on it. so turn it around and look for it there are 2 where the unit connects to the stick
@paulcohen1555
Жыл бұрын
Very good explanation. Can you give the electrical parameters of the motor?
@OpenMeUpTec
Жыл бұрын
sorry i dont know what it is to help you
@paulcohen1555
Жыл бұрын
@@OpenMeUpTec Okay,, that's too technical for this channel.
@vodkarocket1
3 жыл бұрын
Thank you for doing such a helpful video
@OpenMeUpTec
3 жыл бұрын
thanks for your support
@MattConquer
5 жыл бұрын
Very useful howto, thank you a lot!
@OpenMeUpTec
5 жыл бұрын
thanks for your support
@CWP1744
Жыл бұрын
Thank you!
@venjiunchee7443
3 жыл бұрын
Hi, does anyone know what are those Torx head sizes being used in the video?
@OpenMeUpTec
3 жыл бұрын
t8 and phillips the plus shape (+). there is also one t10 which is for the motor
@Shuttu14
Жыл бұрын
The screw mentioned at 3:07, I am unable to remove it. Can someone tell me what kind of screw it is ? It doesn’t have any kind of thread on it.
@OpenMeUpTec
Жыл бұрын
please watch my newer video on my channel that tells you kzitem.info/news/bejne/1Hh503tthHmnpqg
@Iannarellam
2 жыл бұрын
What are the screwdrivers you used I have one but it doesn’t take the screw out for the motor I have the T8 torx
@OpenMeUpTec
2 жыл бұрын
you need a t8 and a t10
@WiktorProsniak
2 жыл бұрын
0:46 my brush bar does not come off. Cant move it. What can i do?
@ms.tiennguyen7871
4 жыл бұрын
Good job!! It’s very helpful
@OpenMeUpTec
4 жыл бұрын
thanks for your support
@analouluwaton3647
5 ай бұрын
Thank you 🙏
@OpenMeUpTec
5 ай бұрын
thanks for your support
@sunethudaramirissearachchi5778
3 жыл бұрын
Thank you.. this is so valuable
@OpenMeUpTec
3 жыл бұрын
thanks for your support
@bolebobbi
3 жыл бұрын
Thank you very much for this Video.
@OpenMeUpTec
3 жыл бұрын
thanks for your support
@BigDDaavvee
4 жыл бұрын
Fantastic video
@OpenMeUpTec
4 жыл бұрын
thanks for your support
@chinchilla07
2 жыл бұрын
The problem I had with this head was that hair will get stuck at the wheels and they are impossible to remove. Do you happen to have a solution to this?
@OpenMeUpTec
2 жыл бұрын
please watch my video on the OPEN ME UP! Dyson V11 and V10 High Torque Head Disassembly and Clean kzitem.info/news/bejne/jqeQp6KdmnxkfKQ at 21.55
@chinchilla07
2 жыл бұрын
@@OpenMeUpTec is it the same way with the v10 fluffy head?
@OpenMeUpTec
2 жыл бұрын
@@chinchilla07 yes it is from the v10. but the v11 and v15 have the same head
@chinchilla07
2 жыл бұрын
@@OpenMeUpTec thanks. I will give this fluffy a try again on my v10. The tangled hair at the wheels was impossible to remove on my v6 fluffy 😅
@dipseadiver
3 жыл бұрын
Very helpful. Thank you.
@OpenMeUpTec
3 жыл бұрын
thanks for your support
@jevgens0789
4 жыл бұрын
I can not take off the big brush roll from the motor, as if there is some screw that is blocking it from inside 😡 it is moving for 1 cm and then blocks.. do not want to force it ...please advise
@OpenMeUpTec
4 жыл бұрын
can you watch the video and tell me at what time you having problems with so i can understand how to advise you
@jorismak
4 жыл бұрын
I had the same thing. Forcing it from the motor side to push it off was what worked eventually for me. I managed to get a screw driver (or some other round stick strong enough to use as a lever) between the roller and the side cap. That 1cm moving you feel? That is _not _ the motor. You probably have the same thing as I have, the little plastic black ring has come off and is stuck between the motor and the roller.
@samclifton3456
4 жыл бұрын
Once I put the head back together, the main roller now is jammed and won’t spin once turned on. Any suggestions??
@OpenMeUpTec
4 жыл бұрын
you probably stuff up somewhere. therefore it is best if you disassemble it again and try again
@matejbandev6466
4 жыл бұрын
I’m having trouble getting the attachment can you please provide me a link here to get it from.
@MissSuperLu
2 жыл бұрын
Only got as far as the screw to take the motor out that thing will not come off 😢
@moderntouchfurniture
3 жыл бұрын
Excellent video thank you.
@OpenMeUpTec
3 жыл бұрын
thanks for your support
@paulcohen1555
Жыл бұрын
There is no sound beyond ⅔ of the video. Is it a problem in my player or your recording?
@OpenMeUpTec
Жыл бұрын
there is no sound for the reassembly part
@ao6bl
3 жыл бұрын
Your good and video is well explained 👍
@OpenMeUpTec
3 жыл бұрын
thanks for your support
@danpeters6
4 жыл бұрын
How important is the black plastic ring near the base of the motor? mine broke off as I was disassembling
@OpenMeUpTec
4 жыл бұрын
can you watch the video and tell me where this black ring shows up. so i understand what i am looking at
@danpeters6
3 жыл бұрын
@@deealba7298 i ended up installing it even tho it was broken, figured it's better than nothing. It's been a few months now and it's been running fine...
@OpenMeUpTec
3 жыл бұрын
@@deealba7298 according to dyson they dont know how to disassemble the head so the only thing left is to buy a new one.
@planouquier
4 жыл бұрын
many thanks for your help!
@OpenMeUpTec
4 жыл бұрын
thanks for your support
@nikw94
2 жыл бұрын
Sorry what type of screw driver do I need?
@OpenMeUpTec
2 жыл бұрын
torx screw driver
@JoeLKidz
3 жыл бұрын
May i ask, does anyone know, is the v10 and v8 ROLLER HEAD MOTOR exactly the same? My v10 roller head motor r broken, I saw v8 roller head motor parts from the web, not sure to buy it yet hmm
@OpenMeUpTec
3 жыл бұрын
it is the same.
@jorismak
4 жыл бұрын
My v8 fluffy is different. It doesn't have the blue small bar, but it has a little gray plastic bar there with two even smaller wheels. Those wheels eat up hairs and get stuck, but I don't know how to remove them. Anyone? (the little black ring one the motor snapped and got stuck between motor and the big roller. The roller was extremely hard to remove from the motor, scary stuff)
@jccc-ly9oy
4 жыл бұрын
What's the size of the philips (not the Torx) screwdriver that you used to remove that one screw on the motor side?
@jccc-ly9oy
4 жыл бұрын
nvm; i have a V11 fluffy and apparently, there is no philips screw; you just tap the shaft and the cover will loosen and you can pry off
@OpenMeUpTec
4 жыл бұрын
can you watch the video and tell me at what time i can see the screw. makes my life alot easier.
@OctozoidPRS
5 жыл бұрын
I am unable to undo the four screws on the clear head. What can I do to get the build up from in there?
@OpenMeUpTec
5 жыл бұрын
is there a reason why you cant. please watch the video and tell me what part(time) you have issues with so i can guide you correctly
@OctozoidPRS
5 жыл бұрын
I do not have a torque screwdriver, What do you suggest. I was trying to use a phillips head screwdriver, and it would not turn any of the four screws.Thank you for your reply.
@OpenMeUpTec
5 жыл бұрын
@@OctozoidPRS flat head is good enough
@mikemark50
2 жыл бұрын
This is a completly different V7 head from the one I have
@OpenMeUpTec
2 жыл бұрын
yes it is since it depends wherer you buy it and what you buy it with. here is the newer version of the video kzitem.info/news/bejne/1Hh503tthHmnpqg
@steveh9229
4 жыл бұрын
Thanks for this but did you clean the roller with detergent. Would it be okay in the washing machine
@OpenMeUpTec
4 жыл бұрын
dont do any of them. the issue it you will loosen the glue and it will come off. go spray it in the back yard with the garden hose
@witphong
3 жыл бұрын
Thank you so much
@OpenMeUpTec
3 жыл бұрын
thanks for your support
@kundlikthopte8548
Жыл бұрын
India in maharashtra spare parts not available
@nadinemena1713
7 ай бұрын
Does this fit the v7 motorhead?
@OpenMeUpTec
7 ай бұрын
yes it fits the v7 to v15 . does not fits the v12 and gen5
@michelleelks9543
4 жыл бұрын
Thanks,this is excellent
@OpenMeUpTec
4 жыл бұрын
thanks for your support
@OpenMeUpTec
4 жыл бұрын
thanks for your support
@PenOtration
2 сағат бұрын
Thank you.
@katlynmitchell6404
4 жыл бұрын
are dyson v10 and v11 tools interchangeable? If I purchase the fluffy head will it fit on my v11?
@OpenMeUpTec
4 жыл бұрын
yes the dyson v11 v10 v8 and v7 are the same tools and will work with each other
@Rivster79
4 жыл бұрын
OPEN ME UP I read that there were voltage differences between some of the models (I.e. V7 vs V11), is this true or is there straight compatibility across the models you mention above with the accessories?
@OpenMeUpTec
4 жыл бұрын
@@Rivster79 yes they are the same thing and just work. voltage difference is the vacuum itself therefore, the head might spin faster in the v11 than the v7. but over all there is no harm
@Rivster79
4 жыл бұрын
OPEN ME UP great, thank you. By the way, super helpful video and content and very speedy reply! Have a great day.
@zihaowang4456
4 жыл бұрын
My wheel is stuck with hair, how to take those two little wheels off
@OpenMeUpTec
4 жыл бұрын
you can pry those off with a screw driver. please note you need to pry the side in the centre.
@nancybenamor873
4 жыл бұрын
what tool are you using to unscrew the soleplate? it's an odd shaped scewdriver head
@OpenMeUpTec
4 жыл бұрын
trox screw and they all start with TXX. they are star shape heads
@MissSuperLu
2 жыл бұрын
@@OpenMeUpTec hi, would you mind sharing which size screwdriver you used for this? I tried a torx T10 75mm and that was too big. Thank you!
@OpenMeUpTec
2 жыл бұрын
@@MissSuperLu it is mostly torx t6 and t8
@shaneyg1988
Жыл бұрын
Do you know how to remove the wheels?
@OpenMeUpTec
Жыл бұрын
in my other video i show you how to remove the wheels. watch the newer version on my channel
@shaneyg1988
Жыл бұрын
@@OpenMeUpTec thanks for the reply. I managed to figure it out about 5 minutes after asking though 😅
@winstonang9793
2 жыл бұрын
what size screwdriver is that?
@OpenMeUpTec
2 жыл бұрын
you need a screw driver set. but if you want to know you need t8 t10 and a phillips
@kroks06
2 жыл бұрын
and V6 ;)
@waulau8
4 жыл бұрын
how you clean the blue rubber hose ?
@OpenMeUpTec
4 жыл бұрын
disassemble it then run that put under water or use the garden hose like i do.
@slarsen791
2 жыл бұрын
Why can’t Dyson use a normal screw head?
@OpenMeUpTec
2 жыл бұрын
because everyone else use there types as well.
@tonyrioux5753
4 жыл бұрын
What bit is needed for the screw on the motor side under the floor rollers?
@OpenMeUpTec
4 жыл бұрын
you still need a torx bit but it is much larger i believe it is T15. can you please watch the video and tell me at what time it shows up as i believe you talking about the screw that holds the motor
@tonyrioux5753
4 жыл бұрын
OPEN ME UP 17:23
@OpenMeUpTec
4 жыл бұрын
thats the end of the video, there is nothing there
@tonyrioux5753
4 жыл бұрын
OPEN ME UP lol sorry about that. Should be 3:30. Appreciate your replies.
@OpenMeUpTec
4 жыл бұрын
@@tonyrioux5753 at 3.30 the screw i remove is the same as all the reset. there is only one screw that requires a bigger torx head which is at 7.05 which is the motor screw
@kennyblacklee
3 жыл бұрын
I accidentally washed the whole thing with a water hose. Leaving it out to dry for 24 hours now. I’m so worried that I’ve spoil the damn thing!! HELPPPPPPP
@OpenMeUpTec
3 жыл бұрын
it is probably not dry yet. if you want, you can open it up to dry it out properly. or as less remove a few things so it dries better.
@rid-rid
4 жыл бұрын
Wow! This is great! Thanks a ton mate. Could you help me figure out a squeaky issue with the motor head? Let me know if I could contact you via email and send you a picture of the part I'm referring to. I just got my v11 weeks ago. Your help would be much appreciated. Thanks
@OpenMeUpTec
4 жыл бұрын
what is the problem. just post the picture online and send me the link here. or watch the video and tell me at what time you have a problem or at what time the thing shows up
@rid-rid
4 жыл бұрын
@@OpenMeUpTec Here is the image. imgur.com/a/BP1bWkA | I have highlighted the problem area (yellow circle). So this wheel is squeaking. Whenever I move the vacuum back and forth, the wheel squeals. It is not loud, but definitely irritating. The sound was there before. I think I may have accidentally hit the vacuum on the floor to get some stubborn dirt off.
@rid-rid
4 жыл бұрын
Sound wasn't there before*
@OpenMeUpTec
4 жыл бұрын
@@rid-rid so you want to know how to remove those wheels. you need to get something to pry it out. you need to put your screw driver or prying tool in side close to the middle and ligt it up. it is a bit hard. you might want to disassble it and you can remove it from the back
@rid-rid
4 жыл бұрын
OPEN ME UP I really appreciate you taking time to reply. Can i just use oil instead? Not sure what oil to use? Someone said use WD40. But isn't WD40 a degreaser? Please advise.
@GeneralFuct
2 жыл бұрын
Sound cuts out half way
@OpenMeUpTec
2 жыл бұрын
watch the newer version of the video on my channel. it doesnt cut as i thought i dont need to explain how to put it back since i already show you how to take it out
@gianelio828
6 ай бұрын
Ma che complicazione...
@lenalomakova
2 жыл бұрын
Change the name of this video, v11 has different head..
@OpenMeUpTec
2 жыл бұрын
i have the dc59 to the v15 and can tell you this came from my v11. But then depending which model you purchase and where you live, you will receive something different
@inxlee
3 жыл бұрын
The damn hose part disintegrated
@OpenMeUpTec
3 жыл бұрын
you clearly had a good run. you can but a replacement i believe on ebay.
@yazmat96
3 жыл бұрын
The big torx is a 15, not 10 ;)
@OpenMeUpTec
3 жыл бұрын
thanks for your help. honestly i dont remember as i have my set infront of me and just use whatever fits.
@ClodFrax
3 жыл бұрын
Maybe it changes by the model? I have v10 and just used tx7 & tx10. Philips the first i found
@hoatam5213
2 жыл бұрын
go to here
@turtlemaster9000
Жыл бұрын
What a horrible design. That motor pipe at 8:36 cannot be removed unless you literally tear everything down cables and all. Mine is full of tangled hair but I cannot remove them because of this. Never buying Dyson again.
@gaoyang7685
8 ай бұрын
🇱🇦
@DadsDo_eMTB
Жыл бұрын
Thank you very much for the video. The fluffy head didn’t spin around so I had to take it completely apart to get all the hair out and twine. Now it works perfectly and you save me £65
Пікірлер: 229