please do more videos regards transmitters, valves, RTD's,.... thanks a lot; best I've seen yet. thanks
@malikgarrett2036
5 жыл бұрын
This video is the best in explaining all steps. I just start taking instrumentation class
@derina.maleek9408
5 жыл бұрын
Please make more videos it is best video I ever seen don't waste that lab you have keep going and we are supporting you
@qzorn4440
6 ай бұрын
An Amazon $80 Riiai 4-20mA 0-24V precision 0.01mA calibrator will work just fine. Hundredth's of a milliamp is adequate. This will save $13,000 of buying a Fluke 754 😎 Nice video
@randiahmed860
5 жыл бұрын
Thank you , it's very interesting information please don't stop up load like these videos .
@1quickchevy2
7 жыл бұрын
Nait was a great place to learn. Great labs, and great instructors.
@shaiksaleem06
8 жыл бұрын
thanks for the video its very helpful for people who didn't have practical knowledge
@geethsri4914
9 жыл бұрын
thank u sir . this most use full and he explain very good and basic knowledge Pearson all so understand
@JZ-Sensor
7 ай бұрын
I love it
@karimtalebi7111
8 жыл бұрын
Great. Please put more videos. I waiting for anothet excellent training like this. Thank You!
@abdulrazaq6581
7 жыл бұрын
Karim Talebi
@abdulrazaq6581
7 жыл бұрын
Karim Talebi nice
@andrewtaylor5972
3 жыл бұрын
What’s the calculation to derive 0.49kPa? Thanks
@athilaldurry5880
3 жыл бұрын
many thanks
@TheCommonSenseProfessor
8 жыл бұрын
I am totally jealous of your lab!
@kaunghtethein3322
4 жыл бұрын
Very useful, thank you. One question, can i not use pressure regulator in the first place and use the actual water level to calibrate? If yes, what difference would that make? Anyone please ...
@megamanwins
3 жыл бұрын
Why you do not upload anymore? its been like 7 years! :(
@rodelpabito7292
7 жыл бұрын
procedure for boiler level dp tansmitter....here the lrv-= -6.683kpa urv= -1.343kpa wet leg type span = 5.34
@estradacantu
8 жыл бұрын
Great explanation
@abdulbilakhiya6026
3 жыл бұрын
Appreciate
@bac4998
5 жыл бұрын
Thanks.
@shamshadall-rounder7619
Жыл бұрын
Why you not mention 250 omh In series conection ? Branch type calibration need also 250 omh
@unupeter7657
Жыл бұрын
U don't need a 250 ohms resistance if u are not hooking communicating device...... The 1151 series transmitter are purely analog and are not hart enabled, the there will be no beed to reduce the loop impedance. Thanks 🙏
@CavadCavidHuseynov
8 жыл бұрын
Superb
@prgomad5392
3 жыл бұрын
What is the name of this facility lab
@totoilongo6132
6 жыл бұрын
Thanks
@Q1W2E3QW
8 жыл бұрын
at minutes 3 you start sir to connect high side to regulator and Instrument Air Supply !!! this made me confused ... what I know , its connect to process - bottom of a tank
@gr8bastard
7 жыл бұрын
Q1W2E3QW the instrument air connection is used for bench calibration purpose.
@Q1W2E3QW
7 жыл бұрын
ok .... why you not use pressure transmitter for open tank instead of using DP Transmitter. as you know, its more expensive ... plus a manifold related to differnial transmitter is more expense than manifold of pressure transmitter...in addition, you dont have to wary about low side to elemenate dust and wind impact.
@rahulmavath4291
4 жыл бұрын
Why you calibrate with Lrv of 0.49 kpa. why you choose that value
@KevinRocket01
3 жыл бұрын
cause its the equivalent pressure of the reference or datum line of the tank. it is the measured pressure where tank is considered zero level. it is common in level measurement to compensate the sludge or sediments settling down at the bottom of the tank.
@amirimaf4203
5 жыл бұрын
tanks
@attacknblack1984
9 жыл бұрын
Can you post some vids about square root extraction
Пікірлер: 38