Great video, thank you. I only have 4 1/2" above my garage door, but I am inspired to put pulleys in other areas of my garage for tables and coolers.
@Housebarons
Жыл бұрын
Hey Syd…, Great! Thx for watching!
@barbaraness4507
2 жыл бұрын
We don’t have a garage, but we do have sheds that this device would work well in. I actually like it for my cabin (she shack), especially because I can also use the additional table space for making things on.
@Housebarons
2 жыл бұрын
Hey Barbara, Nice Thx for watching!
@B_Van_Glorious
3 жыл бұрын
Holy cow. Your choice of music is amazing. I'm inspired, I kid you not.
@Housebarons
3 жыл бұрын
Hey Brian, Thanks for letting us know. Much appreciated. And thx for watching!
@SniperUSMC
2 жыл бұрын
Best set up I've seen, probably cheapest and easiest to install too. Could have used more pulleys to increase mechanical advantage for raising and lowering. Any back up fail safe measures?
@Housebarons
2 жыл бұрын
Hey Sniper, yes. More pulleys would help - no fail safe but I only keep lighter objects up high. Thx for watching!
@arphaksad01
2 жыл бұрын
That's slick.
@Housebarons
2 жыл бұрын
Hey Arpha.., Thanks & thx for watching!
@2-old-Forthischet
Жыл бұрын
Genius!
@Housebarons
Жыл бұрын
Hey Too…, 😃Thx for watching!
@fatalknowz
3 жыл бұрын
Can you tell me what size eye hooks and lag screws u used? Also what maximum weight capacity could this setup hold ?
@Housebarons
3 жыл бұрын
Hey brooklynn... The eye hooks were 3/8-1/4 shaft dia. It’s important to make sure that they will hold the weight - so check the rating of the hooks. They should have a tag stating what they will hold. ( Max is 100lbs for the harness I used ) but I dont max the weight out. I’m only comfortable w/ 60 pounds or so. The biggest challenge I had was clearance because I wanted it to be above the open garage door which was a tight squeeze. Thx for watching!
@kayBTR
4 жыл бұрын
I think you should treat yourself to a second drill, one for predrilling the pilot hole and the other with the screw driver attachment. I got so tired of changing back and forth on a little job and I could have finished in a fourth of the time. Huge time and effort waster for me.
@Housebarons
4 жыл бұрын
Hey KayBTR , I actually have an impact driver as well but didn’t have a drill bit attachment. You are correct - efficiency is the name of the game!! Good point. Thx for watching😃
@stevenhill478
3 жыл бұрын
This is super dangerous. Those kayak lifts are not meant for that kind of weight. Not to mention, the nylon cord that comes with it is junk and frays as it rolls over the pulley.
@Housebarons
3 жыл бұрын
Hey Steven, The lift is rated at 100 lbs. thx for watching!
@stevenhill478
3 жыл бұрын
@@Housebarons right, and your wood alone is 30lbs. That means you can only put 70lbs on that lift.
@B_Van_Glorious
3 жыл бұрын
@@stevenhill478....what are you an insurance rep? Off the cuff it has a safety factor of at least 3x. Most things are 10x. I'm going to assume it's 1/4" as OP said it's rated 100. 1/4 nylon rope has a breaking strength over 1500lbs. I wouldn't use it to pull 1000 lbs; tho you COULD. It's would just melt and be its last run, imo. He could put a trampoline on that and be fine. Stop busting peoples balls when you won't even look up the stats. Safety police are as bad as Grammer nazis. Here ya go. www.engineeringtoolbox.com/nylon-rope-strength-d_1513.html
@stevenhill478
3 жыл бұрын
@@B_Van_Glorious I have 6 of these lifts. Just using them for kayaks and bikes the rope gets frayed which completely negates your safety ratings. I would never attempt to store more than 100lbs on it.
@stevenhill478
3 жыл бұрын
@@B_Van_Glorious and I’m not busting balls… I’m warning potential DIYers that don’t know any better. Too much bad info on KZitem and I don’t want anyone thinking they can lift a lawn mower.
Пікірлер: 24