Just got through watching 50 pallet breakdown videos on youtube. No cost, no welding, no construction. Pure genius. The Egyptians did it like this. Two people make this a walk in the park. Thank you so much.
@DEshav2b
9 жыл бұрын
Outstanding! I had to sit back and shake my head to think of all they ways I have tried, and here you are using two boards. My hat is off to you sir!
@nardibarrios
8 жыл бұрын
Sir, I just got back from my garden, tried your trick, and I had to come in the house to tell you this is the best way to breakdown a pallet, and I can tell you that I´ve tried quite a few different ways. You just got my respect.
@rockwithface
8 жыл бұрын
Thank you so much
@amarjitbassan7310
5 жыл бұрын
One reciprocating saw - £50 One Pallet breaker £25 Set of crowbars £20 All I needed was a couple of bits of wood. I've watched many a video on how to break pallets but this one is up there as being the most impressive. Maximum respect
@SwedeEad
5 жыл бұрын
I just tried this at home! Works a treat. No expensive pallet ripping tool required! Thanks a bunch! (Sorry for all the shouting but something this simple and useful fully justifies shouting about!!!!!!!!!!!)
@RIPCD318
8 жыл бұрын
This is so ridiculously simple. The best method of dismantling a pallet I've seen yet. It's amazing what a smart man with two sticks can accomplish!
@robertdamron7144
5 жыл бұрын
I dont care if this is two yrs old Easiest DIY video I've seen ....even old pallets that have many many splits and cracks come out clean ....thank you sir
@soniacowart5474
7 жыл бұрын
I love this low tech highly intelligent approach! No crazy fast power tools and no expensive prying bars! Thanks!
@akamiguelsanchez9985
2 жыл бұрын
You absolutely genius! I’ve watched so many bloody videos of people suggesting the ‘easiest way’ and it’s either some power tool I don’t have or it ends up splitting the boards. Tried your way and I even got up a board that had already split easily.
@nwkwok
5 жыл бұрын
I tried the method where you circular saw the ends and use a crow bar to loosen the middle nail till you get it to pop off / get the head of the nail to pop out enough to claw it out with a hammer - took me forever, broke the wood often, stripped the nails at times and it drove me nuts. Almost bought a pallet buster cause I was so discouraged. Hopped on KZitem and saw this video, went out to my garage and BAM! broke down a whole pallet in 15 minutes with two 2x4s with ease. THANK YOU, PAUL!
@rockwithface
5 жыл бұрын
Get the pallet wet the night before and it works even better, thanks
@julianlxix
6 жыл бұрын
I return days after watching this video to say thank you. I've tried just about all methods and this one is by far the easiest and most efficient. Thank you!
@GrowWithKit
7 жыл бұрын
Thank you, You have saved me so much time. I found that if you do the middle last it helps avoid the end flinging up.
@tallcedars2310
7 жыл бұрын
Leverage is a great tool, thanks, this is the best method I've seen, and the least expensive! Cheers
@mattcatlett2677
6 жыл бұрын
I agree!
@jorgesantamarina5888
8 жыл бұрын
Thanks, I used this technique. this was very helpful . I saved money because I was going to puchase a tool and there is no need.
@elmarkaz
6 жыл бұрын
Great and elegant solution
@annashiegl
7 жыл бұрын
as a woman, I found this method very good. thank you for sharing
@rockwithface
8 жыл бұрын
For best results with no cracks , let the pallet get wet from rain or wet down with water, the night before to soften the wood. Use even force to remove the boards.. Thanks for watching.
@rockwithface
7 жыл бұрын
Yes
@janecornelius2205
7 жыл бұрын
you need a tride down pallett machine i have one for sale it runs great asking $4500.00 if our intreast init
@tanalee09
6 жыл бұрын
I think I'd try just flipping the pried slats over to use them for leverage. Can't wait to try this. Thanks!
@badberttube
7 жыл бұрын
This is the best vs. simplest method I have seen yet; great idea. Thank you for sharing!
@MrWcampbell2
7 жыл бұрын
Hands down the best method. Just tried it out and worked like a charm. Does take a little muscle, but far easier, and faster than hammer and crowbar method.
@rockwithface
7 жыл бұрын
Thank you
@UriValdez
4 жыл бұрын
Best method ever! I broke down 12 pallets in less than 1 hour, which is pretty amazing.
@rockwithface
4 жыл бұрын
Uriel Valdez thank you
@wideawake5630
Жыл бұрын
Right in line with my philosophy that the best tools are a rock and a stick.
@CharlieboySLONDON
7 жыл бұрын
I never gave much thought to breaking down a pallet i thought it would take 5 mins well an hour and lots of broken boards later i was going to resort to power tools. Thanks for the top tip 👌
@theophilussampson618
4 жыл бұрын
Simple idea but very effective way of breaking pallet, you are a genius
@spankymonkey178
8 жыл бұрын
this is the way,tried it at work today,3 pallets done in about 5 minutes,with minimal breakages...or effort!
@northshorepx
7 жыл бұрын
Excellent technique. Thank you for sharing your idea. It's made my work with pallets so easy!
@aex-blacksmithuk2111
7 жыл бұрын
Nice one. So simple, like all good ideas! Thanks for the tip!
@davidbowman271
4 жыл бұрын
I was going to try and build a pallet buster using threaded pipes but seeing this cost free method I gave totally rethought this, thank you!
@rp6732
Жыл бұрын
Wow. That's awesome. I'm going to use this method. I also have been using my mom's tire jack even though it fits partially. I add a wooden shimmy wedge to help it. It works, but the two board method looks promising!
@madelyn7521
8 жыл бұрын
great idea - no tools required. Going to try this one. Love it. Going to screen my propane tanks with the board
@frankt6906
7 жыл бұрын
I've been doing it this way too. Instead of 2 boards though, I use a crowbar. Oh, and 2 or 3 hammers. And a saws-all. Etc. Yep, just like you. Nice work sir, I've been schooled.
@a.l.alexander3668
6 жыл бұрын
Paul, That looks awesome! On my way out to look for pallets now. Thanks for the additional tip of wetting the boards also. Too Cool!
@jamaljinin569
6 жыл бұрын
Genius! Simplest method I've seen so far. Thank you!
@martino.malley9276
7 жыл бұрын
Simple but effective. Great job. Thanks.
@rockwithface
7 жыл бұрын
+thanks Martin O.Malley
@Khamomil
7 жыл бұрын
There's a touch of genius right there!
@botadecasquillo
8 жыл бұрын
So far the best method I have seen, works grate ... Thanks for sharing
@andrettibark
7 жыл бұрын
I'm just watching this going "why the heck didn't I think of that?" I was doing a harder version by placing a lot of weight on the corners, and using 2 crowbars and spacer blocks on the ground. thanks for simplifying that for me.
@troxycat
8 жыл бұрын
This is brilliant! I no longer hate breaking down pallets!!!
@rockwithface
8 жыл бұрын
+Thank You troxycat
@patrickellis2626
6 жыл бұрын
A nice quirt way to take em apart My neighbors will appreciate it. Thanks for the video
@CammiesGarage
6 жыл бұрын
Shockingly simple and effective. Nice.
@ferriswilliam
3 жыл бұрын
Superb ... im amazed at such simplicity ... been looking around for ages for suitable method .. thank you sir
@Asrapx
8 жыл бұрын
Thank you very much for such an elegant solution.
@indianajones9244
8 жыл бұрын
This is a great idea also quiet so I can do this without disturbing my neighbours
@TheEasystreetster
7 жыл бұрын
Find the laziest man on the job, he will find the easiest way to complete the task. Work smarter not harder.
@MichaelDavidHiltner
7 жыл бұрын
My thoughts indeed! Just how I made it through life so far!
@punknhead23
7 жыл бұрын
Hmmm...the laziest man in my workplace leans back and watches everyone else get it done!!
@bingobongo9203
6 жыл бұрын
Tracey Vincent my father said a hard days work never killed anybody but he wasnt taking the risk
@Ginny2708
6 жыл бұрын
Genius test so simple. Can't wait to try this method.
@bearpitrock
7 жыл бұрын
Dude. So simple! Genius. Thank you!
@Cankuwicasa
8 жыл бұрын
This solution is genuinely "eloquent." The degree of labor and the investment of toolage is far and away superior to anything I've seen to date. A homeless wino could disassemble enough pallets to build a pretty decent shack in a couple of hours, never mind what a skillful, well- equipped wood work worker could do. My interest in palletized lumber has just been rekindled. Still got the problem of no salvage pallets to be had in my area, but the creative juices are flowing nevertheless.
@HaphazardHomestead
9 жыл бұрын
I'm going to try that! With 2 people, one on each side of the pallet, it would go so fast, and not be so noisy as other methods. Time for a pallet party!
@embwee
8 жыл бұрын
no cracks! thanks for the tip--a few days ago, with a crowbar and an uneven board, and a yard full of mud, you know that board had me up in the air in and on my back --- twice.
@TheMrpiggyboy
8 жыл бұрын
Wow! What a great idea, so simple and so easy.
@bobbymac1319
7 жыл бұрын
awsome video bro , thanks very much, saved me loads of time and energy
@raymondvandamme224
9 жыл бұрын
Used 4. But still resourceful. Thanks 4 sharing.
@GOLDSMITHEXILE
3 жыл бұрын
try using one single bar, insert it and stamp down hard and fast (no hesitation) They generally spring off in one piece. Thats how I did it as a pallet refurber on piece-work, and I had to get my stock of spare boards in my own time. Over the years the lads had tried all sorts of methods, and this was what we arrived at as the fastest and most efficient. In the time you did this video I'd have broken down 4 or 5 pallets with at least 80-85% usable boards (sometimes 100% depending on what timber was used, age and condition, wether annular rings or plain or wired gun nails were used, what size, single/double or triple nailed, how rusty etc) Anyway, I earned my crust and paid the mortgage on it.
@0neBadMonkey
6 жыл бұрын
What the hell!! The pallet you are taking apart has been made with love and is perfect with two straight nails at every section. Every pallet I've ever got my hands on was nailed together by a sexually frustrated trigger happy Psychopath.
@backalleykitchen
6 жыл бұрын
Glad I found your video! Thanks for sharing
@pauloroarty1799
3 жыл бұрын
Excellent process I will be doing this tomorrow.
@cactuswren9771
7 жыл бұрын
WONDERFULLY sensible and easy!! Thanks!!
@rockwithface
7 жыл бұрын
Thank you
@UriValdez
6 жыл бұрын
Genius! Lovely method
@jasonpatterson8091
8 жыл бұрын
I'm wondering how often one of these pops up suddenly and makes the worker wish he were wearing a cup... :-) Interesting method though; I really like it.
@MAGAMAN
4 жыл бұрын
If you were really worried, you could put something like a heavy blanket or moving blanket on the board.
@NaulterEgo
4 жыл бұрын
Not gonna lie was waiting for this exact thing to happen. One in a thousand and this method no longer makes sense.
@vicall67
7 жыл бұрын
Thanks! was wearing myself out, using a pry bar and hammer. This way is so much faster, too.
@vizorsdownontario
8 жыл бұрын
straight up well done!
@moisessaldivar4156
7 жыл бұрын
very helpful and inexpensive. great job.
@ether8494
5 жыл бұрын
This is a great way of doing it I use this way. But i like it when the pallet is wet they don't split and they come off so easy. 😊👍
@meliciouscakes
9 жыл бұрын
Def gonna try this method!!! Thanks!!
@thatboybilly
9 жыл бұрын
Thanks mate, I just used this technique and it work!
@johnswimcat
8 жыл бұрын
Looks good, very simple and no cost. I made a steel bar with adjustable L jaws which has been quite good. Once one side of boards are off I can open the jaw wider and lever the blocks or main members off the boards which doesn't cause any splitting. I have wondered about using my hydraulic ram with it's crocodile jaws and some drift timbers to force the boards apart but haven't tried this yet. To make a pallet really strong for use as a bench or table one could open the joints a little, get some good waterproof glue in there and close them again
@johnswimcat
8 жыл бұрын
Hmm! Maybe the same place that you typed your comment! Or perhaps a public library or a wine bar with wifi where you could borrow someone's tablet or phone... While drinking some wine...
@icecreamladydriver1606
6 жыл бұрын
That was really fun to learn. Thanks.
@tiffanytuttle1009
Жыл бұрын
This is a game-changer! Thank you!!!!
@rockwithface
Жыл бұрын
Thank you
@David-qe9lq
7 жыл бұрын
excellent. would never have thought of this. thks.
@austrorus
8 жыл бұрын
indeed,simple and easy to do... what are you doing withe wood from the pallets?
@RobertErickson
3 жыл бұрын
I've broken down a couple of hundred pallets. This way should always be the first one to try. How sweet it is when it works. But just like people, each pallet has it's own personality. Sometimes the pallet is cooperative. Sometimes it a battle. Sometimes all out war.
@rockwithface
3 жыл бұрын
get it wet the night before for best results
@hannahloulou8417
6 жыл бұрын
Just did it. Thank you it really works.
@Whatthaonabout
7 жыл бұрын
Excellent method
@aprilpinkard9929
3 жыл бұрын
WOW😳. THANK YOU, Mr. Genius!
@Boemel
3 жыл бұрын
This is hands down the fastest way of doing so, it should have 10mil views. All u need is leverage.
@lindasuehundley6864
5 жыл бұрын
Pure elegance! Gonna try this. I'm hoping it's mostly leverage instead of upper body strength!
@GIRAF92
7 жыл бұрын
I dig it. Thanks dude
@stu7647
4 жыл бұрын
I have been using one spar in against all edges to remove the slats, it works a treat. Can dismantle a full pallet in under 2 minutes
@rogerdodger5415
2 жыл бұрын
Thanks so much! That helps a lot! ❤️🇺🇸❤️🇺🇸❤️🇺🇸❤️🇺🇸
@chrispeterson1195
8 жыл бұрын
like it thanks I think when I try it nail those leverage board onto the pry board thanks again
@CoachTMAC
4 жыл бұрын
GREAT ...... after taking apart 20 pallets to re-purpose for my home garden, I find your two board method. I will try it on my next project. P.S. I only needed six pallets, but keptbreaking the boards. haha.
@rockwithface
4 жыл бұрын
Coach TMAC wet the pallet with water the night before will reduce the cracking
@CoachTMAC
4 жыл бұрын
Paul Ashe - thanks Paul. With churches close up here in Ottawa, I have some extra time this weekend and about six pallets into take apart. It’s suppose to rain to day. Thanks.
@airbrushken5339
7 жыл бұрын
Simple, but I would consider using it on an old pallet... but for green timber, I got to give you credit!
@danielortizdecaracas
9 жыл бұрын
Thanks mate, good technique and it work!
@MaxMinXX
Жыл бұрын
Ok I need to try this tomorrow.
@fuqarhade
3 жыл бұрын
This is magical
@jason3000tt
8 жыл бұрын
Great work.....this really helps
@valeriemartin3704
9 жыл бұрын
Worked great!
@fuqarhade
3 жыл бұрын
I tried this idea, in fact, I was amazed by the result, the percentage of damage decreased to less than 10%, before that it was not less than 70%
@debraarizona4809
6 жыл бұрын
Iam impressed!! genius,awesome video thank you!😊
@dtriniboss
9 жыл бұрын
An easier and more efficient way to dismantle a pallet would be to rig up a some half inch angle iron bars into a 'U' shapes with nuts and bolts holding the form of each rig's 'U' shape. These U shaped rigs would then be pushed through the gap in a pallet. A hydraulic jack would then be mounted on the open end of the rigs to pry the rigs open. Thus forcing the pallets planks to separate from the post boards.
@christinatenhoeve4581
8 жыл бұрын
how would that be easier? ? didn't even understand what you said!? lol!!
@eltallerdefred1989
8 жыл бұрын
wonderful! thanks a lot!!
@susandruce1064
7 жыл бұрын
what a bloody good idea ....thankyou
@tinker2561
6 жыл бұрын
I've never seen this method before. Thanks for the pro tip buddy =) Duby
@d4m0nm
9 жыл бұрын
AWESOME! Doing this on a surface higher off the ground would save your back too!
@alansmith1931
8 жыл бұрын
Best Idea by a mile , well done :-D
@rockwithface
8 жыл бұрын
Thanks
@sukavuka
6 жыл бұрын
Bro that is awesome ty so very much.
@richarde5718
5 жыл бұрын
Sweet I have 100s of pallets to take apart I'm looking forward to trying this
@serenity6988
7 жыл бұрын
A thinker! Impressive!
@chanansiegel834
8 жыл бұрын
What type of boards do you need to use as the leavers?
@rockwithface
8 жыл бұрын
+Chanan Siegel any type of wood
@AntonioRey4
5 жыл бұрын
Great technique
@charlesacrosbyify
7 жыл бұрын
try this cut a notch on one side of your 2x4 at the end on the other side of the same and cut an angle put board in between edgewise works very easily
Пікірлер: 219