Just an added piece of information, would be to go ahead and check clutch alignment to make sure the belt is not riding on one side or the other on either of the primary or secondary clutch sheaves. Misalignment will cause premature belt failure and slippage and then again with misfire codes. Which is just at that point, essentially a timing issue between the crankshaft/output shaft and the input shaft of the transmission. The ecm knows no different, just that there's a timing issue somewhere. Nice video. Keep up the good work 👍🏼
@BackboneADV
7 ай бұрын
Good point. Another piece of information related to that is to check the transmission mount bolts in between the motor and the trans. Those bolts can jiggle loose and throw off your alignment. We see that quite often.
@Jacksonville_thrashers
Жыл бұрын
I just wanna say thank you very much for the video. 👍👍
@free4life79
Жыл бұрын
Great video, well done
@jocsanromero5388
2 жыл бұрын
Thank you so much for this video! I borrowed my cousins RZR and this same thing happened to us. Now I can return it in tip top shape. Life savers!
@user-ji7dn6wg2m
7 ай бұрын
Nice to meet you where are you located
@nandodrea
Жыл бұрын
It can also be your spark plugs
@drd1924
Жыл бұрын
Dang tell that girl she knows her stuff, how to diagnose a belt, how not to cross thread stuff, that's about 5 more things than most people using these machines know.
@BackboneADV
Жыл бұрын
I'll tell her. She's a great little mechanic and tough as nails.
@kellydavis4954
2 жыл бұрын
how could a bad belt cause a misfire code ,just got a 22 rzr xp 1000 and am all in on any information i can get
@BackboneADV
2 жыл бұрын
Honestly, I don't know. All I know is that for me, it's a regular thing. At least 3 times a week it happens to one or more of my fleet. You can also get a cylinder misfire code when one of the injectors isn't working. 99 times out of 100 it's a broken or shorted wire in the main wiring harness near the motor mount. In your RZR, it's a green wire for cylinder 1 and a pink wire for cylinder 2
@kyledandoy843
Жыл бұрын
Just had cylinder 2 misfire code and turned out the fuel pump went out. Was only getting 15psi of pressure. Should be getting around 58. RZR 1000
@BackboneADV
7 ай бұрын
You're right. That is another common problem with these things. Easy fix though. We use the All Balls fuel pump and they seem to hold up well.
@brittmann3600
7 ай бұрын
hey have a 2018 general 1000, has a cyl misfire code, even at an idle is only running on 1 cyl, ive checked all wires going from ecu to injector all is good, will lose injector pulse to cylinder on drivers side.......any ideas?
@cameronwilfong8388
Жыл бұрын
Hey man I’m haveing a problem on a 1000s no spark or feul in cylinder one good compression both cylinders new clutch belt all that new coil pack plugs and wires
@flatfootfun9524
Жыл бұрын
Forgot the most important part on the clutch. The little plastic washer
@BackboneADV
7 ай бұрын
You got that right. Those damn things wear out so quick. Sometimes when we rebuild a clutch, that washer is completely gone.
@jakepeters3291
Жыл бұрын
Is there a way to reset the check engine light on a 2016 Polaris 900
@Super-no1fx
Жыл бұрын
Love ur vids guys!!..is there a course online or another tech course available specifically for Polaris rigs? Hell I’d love to come work with u guys for few weeks and learn what I can .. what will it cost me ?
@BackboneADV
Жыл бұрын
We find a lot of help on google forums and youtube, and polaris does make some great how to videos and blogs. For learning with us- email estesjeep@gmail.com and see where that could get ya
@Super-no1fx
11 ай бұрын
@@BackboneADV thank you Madison!!
@MotoXXX7
5 ай бұрын
You forgot to torque the primary bolt with a torque wrench.
@dgensher
2 жыл бұрын
Can anyone help me please I have 2015 Polaris rzr XP4 with code P4405, can anyone help please?? Can't find any info on it
@user-ji7dn6wg2m
7 ай бұрын
Nice to meet you where are you located 4:06
@israelapodaca8060
Жыл бұрын
How did the check engine light go off after you fixed it or does it go off by itself?
@BackboneADV
Жыл бұрын
You can disconnect the battery and touch the positive and negative cables together for a few seconds and then hook it back up. Or, you can drive it at over 4000 rpms a couple of times for a few seconds each time. Sometimes that misfire code will come on because you run the machine in high range going too slow on steep hills. Basically, if that belt starts to slip quite a bit, that code will come up.
@bmf24
2 жыл бұрын
First thing I was told to do was to change those square pucks to rollers.
@BackboneADV
2 жыл бұрын
Yep, for sure
@tazzthedoodle7861
Жыл бұрын
Is that your daughter? She is very smart. My clutching advice is to get rid of those square pucks in the secondary and go back to the rollers.
@MiguelGomez-cd7fk
2 жыл бұрын
Did the cylinder misfire code ever get cleared ?
@BackboneADV
2 жыл бұрын
Yes
@mariasalvator4831
2 жыл бұрын
Hi I could use your help on like what to do for our polaris 2016 rzr 900 it turned off on my sisters bf when he was riding it’ll turn key but won’t turn on all the way , & no check engine light is on the dash
@BackboneADV
2 жыл бұрын
Oh damn! Back in 2016 and 2017 I ran RZR 900's. I had 4 or 5 of them do that to me. In every case it was the damn wiring harness. We ended up replacing the entire wiring harness on 2 of them before we got sick of that bullshit and just traced down the bad wire. It was a chore either way.
Пікірлер: 37