Actually two things. ONE short blow downs like open mufflers. Polishing doesn't do anything. In fact can actually hurt as laminar flow actually cuts effective cross sectional area of the port, a fluid dynamics thing . By raising the exhaust, that hurt you a tiny bit. Also unless u have stuffers in the crank like a 550, adding case volume can hurt a bit as well. Of course it's the "sum" of all the changes that matters. Back to the exhaust, that little Piston Needs MORE time under pressure on those not less if your wanting torque. I cut the cylinder base to get around 0 squish, THEN cut a popup to get around .018 squish in the final form. Gets more punch & effectively adding compression along with lowering the exhaust a bit. Love the video format and enthusiasm :)
@novicelumberjack
Жыл бұрын
I LOVE you Walt! I am so proud that I got you to watch my channel! I have watched and learned from soooo many of your videos. Thanks for commenting. I watched your 555 build up, but I'll watch it again with more of a critical eye. This build I did end up giving a bit more torque over stock, as it holds its rpm better in the cut. I did another video putting it up against my ThunderKitten (ported Echo 4910) with a 22" bar. With all that bar buried in red oak, it was able to hold its rpm and walk away from it where the ThunderKitten slowed down under the heavy load. So even though it isn't any faster in smaller wood, it really holds its rpm in the bigger stuff, acting like a much bigger saw. I was so impressed with it that I went ahead and purchased myself a Redmax 5000. When I port it, I will concentrate on doing things as you suggest to raise compression and keep the exhaust roof lower since I now know that you can't really get any more rpm out of these but you can substantially increase their torque.
@ChattanoogaDan
Жыл бұрын
I bought a 545 mark II as a farm saw. I cut a ton of trees every year, probably 15-20 full grown oaks and several pines, hickory etc. This saw is incredible out of the box; reliable, strong and manageable all day long
@Southpaw226
Жыл бұрын
Do you run .325 or 3/8? I run the 325 xcut and oregon lpx on a 20” bar, considering trying 3/8 on and 18” bar
@KRAVATTNET
Жыл бұрын
The bottle neck on the 5 series is the air intake. Open up the top cover with big holes around the air filter and big gains are found.
@Houseworksaws
Жыл бұрын
I agree!
@craigunderwood4353
Жыл бұрын
The 545 is the best 50 cc saw out there period! Nothing comes close to it!! I have taken down a 25" red oak with it, bucked and everything!!!
@paulherman8961
Жыл бұрын
Best video on saws I’ve seen and appreciate honest saw talk. New subscriber here with a 2013 545 Auto-tune Husk w/ 18” stock bar and .325 chain. I love it!
@joshuajohnson4396
Жыл бұрын
I ran a 550xp and it was a great cutter once you learned how it liked to be ran. Very impressed for a high cut speed style saw. Thanks for your knowledge that you give us all through watching your experience
@novicelumberjack
Жыл бұрын
Exactly, 550 likes to stay high in the rpm's.
@Mark-Marine
Жыл бұрын
Thanks for your honesty - not just in this video, but all you’ve shown. I’m getting ready to heed your advice. Thanks again
@justintime8095
Жыл бұрын
I think the dyed plastics make it faster. Love your channel. No need to beat yourself up. You content is high class
@novicelumberjack
Жыл бұрын
They definitely look good, that's for sure!
@eriklong6390
Жыл бұрын
Very happy to see that you didnt try to exaggerate the gains that were gotten (or not gotten) from porting that saw. That is why I keep coming back. I like that I can trust your word and your opinion is honest. Thank you for posting the true results. Also, looking forward to seeing Hot Rod and SOFT HANDS STEVE!! HAHA! You did a great job with those characters of yours. Love it.
@duck-n-cover477
Жыл бұрын
You saved me from tearing into a couple factory saws. They run great already, but it's good to know there aren't a lot of gains to be had. You validated Husqvarna delivers greatness from the factory. Love my saws, Husqvarna (545 mkii) and Stihl (400c), so not biased. They're straight up great saws.
@slomango7927
Жыл бұрын
Crazy combo! I just bought a 545 and was eyeing the 400c lol currently have a echo 450 also
@adrianjackson4561
Ай бұрын
400c i was not impressed with it i have a jonsered 2172 and that thing smoked it while running a 28” bar and the 400c was using a 20” only a 3 cc difference
@donaldsmith6404
6 ай бұрын
I love my 545 mark 2. One the best firewood saw I’ve ever owned
@SNELLERIZED
9 ай бұрын
I never found much gain when porting a 550, which is why I did very few of them. Perhaps others have them figured out better than I did.
@elijahskiver6429
Жыл бұрын
I dont have much experience porting but every video i watched on the 550 mark 2 said that the air flow was constricted. Are opening up the muffler a bit it definitely helped, especially by not needing to be run at the highest rpms for a good cut.
@1212zorz
6 ай бұрын
Great video! I've just torn into a 545 M2. Also noticed the super short blowdown right away. And that the exhaust side of the piston and upper transfers are black. It seems to be a pretty dialled saw from factory with the exception of the what I can only assume to be emissions regulations encouraging husqvarna to choke their mufflers and and re-burn their exhaust gases.
@KEWS54
Жыл бұрын
Thanks for your burial honesty!
@Jesusiskingamen7
Жыл бұрын
This is my favorite firewood saw love this saw
@Houseworksaws
Жыл бұрын
I have 3 550xp MKII and just love the damn things. I’m going to send one out to get ported. Should be a blast to run after that.
@novicelumberjack
Жыл бұрын
Send one out? Figured you'd be doing it yourself.
@Houseworksaws
Жыл бұрын
@@novicelumberjack If I end up getting a bigger lathe then I’ll do it myself. It’s a real pain to cut the squish with my small lathe.. I gotta step up my lathe game and sooner than later.
@0808dsmith
Жыл бұрын
I sure looks and sounds better under load to me! On the downstroke there appears to be little to no change, but the tug up looks slightly better! If you were porting for torque, I believe you got some gain!
@ToddAdams1234
Жыл бұрын
1st, haha! Seriously though, glad to see you back. I’ve got to go to a neighbors and cut some wood for him and all that he wants is for me to haul away the wood, it just happens to be good firewood as well. We’ll see how it goes!
@jonathanhensley8685
Жыл бұрын
Awesome video man You’re the man for being a man. A little tidbit of information that I hope may help not you cut out of the cylinder and made flush with the transfers when the piston is it bottom dead center it covers that up and slows down the transfer of fuel Transfer before bottom dead center You can scallop the bottom of the piston lining it up with that same area be sure and take some measurements so you don’t Freeport in my experience you can only take about half to 2/3 off the piston that you take off the Cylinder. If that makes a lick of sense
@novicelumberjack
Жыл бұрын
I think I understand you. I will have a Redmax GZ5000 in soon. When I port it, I'll be on the lookout for what you're talking about.
@novicelumberjack
Жыл бұрын
And watch the Wack-Off of the 545 vs the ThunderKitten. I was really shocked. Torque for days on that little bastard!
@jonathanhensley8685
Жыл бұрын
There good saws. you got some good content and you make me me Laugh. That’s a 2 for 1 lol. I have a 550 xp mark 2 on my bench I can send yon pic. If you have phone number to seen to.
@Anthony071177
Жыл бұрын
Really good video. I thought the side by side comparison was pretty surprising because I honestly ain’t very familiar with that model. After porting it definitely seemed a little stronger an consistent but it was so close finishing. But like you first set out to accomplish, you wasn’t trying to make a performance saw, but just a strong working saw with a little more torq. So mission accomplished.
@Boone860
11 ай бұрын
That’s why I love this channel because you show the good the bad and the ugly
@novicelumberjack
11 ай бұрын
I try. Sometimes the truth hurts.
@duck-n-cover477
Жыл бұрын
You've also shown well, how a strong smaller saw 50cc (16" or 18" bar) can cut quick through big wood, because of maintaining faster chain speed (with a shorter bar and without the load of larger sproket) along with a sharp chain.
@Revellersaws
Жыл бұрын
If you have to work in the elements all day every week, just the idea that your saw is ported and you are getting more done than without it is a mental leg-up. You wont run tests like these on the job, so if it feels faster, its done its job. Even tough lumberjack guys have feelings.
@FALLONMICHAEL1022
Жыл бұрын
I’m glad I watched this video before I got into modding my 545 thanks! And I’m with you on the torque over speed. Although I’m just a firewood arborist!Lol
@cajun3197
Жыл бұрын
Almost like husky knew what they were doing with that super short blowdown😂😂😂. Can you make more gain from those? Maybe sure it’s possible, but them things out if the box are amazing running saws. Good vid Boady keep it up 👍🏽
@edzeigler1164
Жыл бұрын
I think it didn,t make enough difference to need porting. They are really good right out of the box.
@RainVale
Жыл бұрын
Can't wait to see this saw against the Thunder Kitten! I've had good experiences with the 550xp mark II, and the 545 seems to handle the same, great saws.
@Brian-Outdoors
Жыл бұрын
550XP Mark II is an amazing saw.
@jasonmorton4168
Жыл бұрын
Thanks for being so honest not many would be
@novicelumberjack
Жыл бұрын
Thanks! Watch the upcoming Wack-Off, it really comes alive with a big bar and big wood!
@cajun3197
Жыл бұрын
Sexy lil saw! That make some great runners🤙🏽
@Witschor
Жыл бұрын
I just ported one of my two 545 Huskys. My experience is , if you go to 78 Intake ,she comes rich barking out of the idle ,if you let her idle 30 seconds after the cut. like she´s overfueling.You can hear it at 10:01min. I went to 100 ex and 78 intake with stock Trans and throw a Red barn Popuppiston in to compensate the less Compression caused of the less 4 deg Ex Timing.She cuts real Nice with s tiny Mufflermod, but i think 78 is to much for mine. Please show the Mufflermod. I Dyed mine like yours and it seems ,that the Cover turned out kinda violett like mine did. Starter is dark black like mine. Maybe it hast du do with the age and heat that got to the Cover. Brand new Covers turn out dark black.
@jeffreyhagelin5927
Жыл бұрын
Raising the exhaust hight also lowers head compression.
@GREGSGUNSONLINE
Жыл бұрын
Thanks you learn what I have learned X torque is a hot saw out of the box.
@novicelumberjack
Жыл бұрын
It did end up livening up and had considerably more torque. Noticed it with a longer bar. With the small bar, it wasn't any faster because it could pull it just fine, even in stock form, but when I switched to a 22" bar and in bigger wood, it wa capable of holding rpm better and therefore faster. It pulled a 22" bar as good as a stocker pulls an 18" bar. So in the end, I did get what I was aiming for. Watch my other videos with this saw and you'll see what I mean.
@derekbush8442
Жыл бұрын
Gained a new sub here ! Thanks for your honesty! Awesome little saw!
@blacksmoke5009
4 ай бұрын
What is the reason for pulling out on starter cord before shutting off saw ? I’ve seen several videos of this but never knew why ? Thanks for sharing 👍
@aaronpowell4885
Жыл бұрын
Love it❤ thanks for sharing👍🏻
@novicelumberjack
Жыл бұрын
You're welcome!
@jwoods345
Жыл бұрын
I've heard the 545 has a wider sweet spot in the power band than the higher powered 550 which makes it more forgiving when leaned on.
@novicelumberjack
Жыл бұрын
Precisely. 550 is high-strung.
@troy3052
Жыл бұрын
Thanks for the honesty
@majorpixchannel7146
Жыл бұрын
Awesome content 👏 👌 👍 🙌 😎 Started my channel inspired by you! I'm also going to do a nock-off of the wack-off lol we should race 🏁 and build videos... I have lots of the same saws! I follow your old channel and came to this one! Thanks 😊
@CutterCH
Жыл бұрын
I keep looking at getting a 545. I need a 50cc class saw. I'm an Echo and Husqvarna guy. The 4910 & 501p are great saws but I want to be different and let Husqvarna handle my next 50cc class saw.
@nickbauman5596
Жыл бұрын
Thanks for your honesty
@novicelumberjack
Жыл бұрын
You're welcome. I'm nothing if not honest.
@Daniel-pr3we
10 ай бұрын
I have the 1st generation 545, and I did muffler mod on it, and that thing screams. I almost believe it will out cut my echo CS590 with 620 mods.
@JS-oy6nn
Жыл бұрын
I only run ported saws have for years. XS saws are my favorite. Kevin is an incredible guy. His work is exceptional and his saws are extremely powerful. Stock saws just don’t do it after running a ported saw. You have really got to be careful WHO you send you’re saws to because there’s too many HACKS out there pretending and only want you’re money.
@novicelumberjack
Жыл бұрын
I've only seen Kevin's saws on his KZitem channel and they look excellent. I have been told of him before and his abilities. Seems very solid. This evening I will be posting a Wack-Off between my Briso ported Echo 4910 and this 545. I'll say this, the 545 came alive with a long bar on it, and the torque I was hoping to get from the porting is abundantly clear. VERY happy with the results after further testing.
@Orefamilylawncare
Жыл бұрын
My guess is that since it's a auto tune saw the computer always making adjustments is probably why you aren't seeing the drastic changes you normally would see.
@user-sv9sf1ns7g
Жыл бұрын
would be interested in watching 545 vs 550 xp def interested in both about 50 dollars in price difference
@adrianstefan23
Жыл бұрын
Like 👍👍👍👌👌
@EcSsAwS
Жыл бұрын
I miss that 545. Send it back to me
@roostercoggburn7436
Жыл бұрын
Great honest video! Keep them coming! Love to see this head to head with a ported/muff modded echo cs490/4910
@novicelumberjack
Жыл бұрын
It's coming this evening!
@novicelumberjack
Жыл бұрын
It's coming this evening!
@kingsaws
Жыл бұрын
Nice kkg shirt and good job on the 545
@ToddAdams1234
Жыл бұрын
What was your squish like? How many thou? I’m just wondering what that compression was, like how many PSI?
@archiemills7251
Жыл бұрын
I don't really need a 545, but I'm thinking about getting one anyway
@crazyfeller5704
Жыл бұрын
👍conservative changes, conservative gains.
@coreycorp7048
Жыл бұрын
What was the squish and compresion before and after porting? If it had gained compresion it would have alot more torqe. My ported 550 mark2 is night and day stronger than my muffler mod only 550mk2.
@Houseworksaws
Жыл бұрын
Band and base was probably cut tho..
@coreycorp7048
Жыл бұрын
@@Houseworksaws Yeah cutting the band and base is part of doing a good port job.
@mmholling87
Жыл бұрын
Who ported your saw?
@Fishinmech24
Жыл бұрын
Way better saw
@edzeigler1164
Жыл бұрын
Yes torque is nice
@roofertilldeath2071
5 ай бұрын
Advance the timing!!!
@laszlopap19
Ай бұрын
I see that I would only give you a Chinese machine for cutting wood it's okay if it breaks. Of course, it is no problem with a lying tree everyone can go there, there can be no problem
@user-cc7db1sv3m
Жыл бұрын
Where was the upgrade parts located I have a 545 mark 2 I want to upgrade and is the bass gasket delete worth it?
@SCouch-cw6je
Жыл бұрын
Difference between the 545 and 550 the 550 has stuffers the 545 like the 555 does not. The mark2 I’ve done you delete the base gasket the piston stops on the band.
@novicelumberjack
Жыл бұрын
Stay tuned for this evenings Wack-Off. You'll get to see how this 545 comes alive when expected to pull a long bar.
@vikingnorm6935
Жыл бұрын
Subbed
@rebeccarobinson7024
Жыл бұрын
Nice job ya torque is sometimes better and love my stock 545 mark 2 and was wondering if I had it ported if would make difference and this video just answered that question lol
@novicelumberjack
Жыл бұрын
Hang in there, today's Wack-Off is going to really showcase what the porting did for this little saw. It isn't faster in small wood, but boy oh boy, did it come alive in the big stuff!
@rebeccarobinson7024
Жыл бұрын
@@novicelumberjack OK waiting for that lol now got do a wack off against the timber kitten 590
@novicelumberjack
Жыл бұрын
@@rebeccarobinson7024 are you a female? Or using your wife/girlfriends account? Don't have many female viewers.
@williamkangas4187
Жыл бұрын
Never heard of a 645
@rebeccarobinson7024
Жыл бұрын
@@williamkangas4187 lol ment say 545
@matthewsmyth903
Жыл бұрын
Bought mine from Lowe’s and chain guard was broken could not start
@wilkey40
Жыл бұрын
There are old bulls and young bulls I prefer to be the old bull
@lumbearjack1439
Жыл бұрын
Try it with a longer bar, I bet it will it with authority. You didn’t really do much to increase speed but I bet the torque is greater with a big load
@novicelumberjack
Жыл бұрын
You are gonna love today's Wack-Off.
@lumbearjack1439
Жыл бұрын
@@novicelumberjack awesome! Every time I log into KZitem I refresh my feed looking for the next video you post!
@bethanyhaskiell9116
Жыл бұрын
Do you cut the keyway on the flywheel to advance timing along with port work to see if its worth any power
@novicelumberjack
Жыл бұрын
I haven't yet. But I am looking forward to trying it in the future.
@bethanyhaskiell9116
Жыл бұрын
@@novicelumberjack I think you will see a little bit of a gain on a ported saw but probably not as noticeable as if the saw was stock with just a muffler mod
@tedneitzel
Жыл бұрын
Little saw rips
@j.c.lawntreesnow6272
Жыл бұрын
Boedy do the transfer caps have restrictions in them like the 365?
@novicelumberjack
Жыл бұрын
Nope. At least, I didn't notice anything.
@jerseyjoshua4818
Жыл бұрын
Yes they have restricted caps like the 365 X-torq. You can replace ALL THE TRANSFER CAPS on the 545/550, 555/562, 565/572. The transfer caps along with crank stuffers are the big differences between the saws.
@jerseyjoshua4818
Жыл бұрын
All those saws share the exact cases within each cc class. The transfer caps being larger & less restricted in all the XP models. The 4 series is the only homeowner, non professional offered by Husqvarna. All the 5 series are professional grade. XP model just getS MOAR POWWA.
@novicelumberjack
Жыл бұрын
@@jerseyjoshua4818 So, sounds like you are saying that they are smaller and therefore more restricted, not necessarily a "restriction" inside it...right?
@jerseyjoshua4818
Жыл бұрын
@@novicelumberjack Boedy correct. You can switch the caps on the 365 X-torq and essentially turn it into a 372. I do believe they have different cards on the 3 series. That's why I was telling you to switch the caps on the 2258, so you'd in essence make it a 2260/562.
@FernandezCycles
Жыл бұрын
1:33 same
@Jesusiskingamen7
Жыл бұрын
Do you buy new stickers to put on after yiu dye plastics?
@novicelumberjack
Жыл бұрын
Nope, just drop the whole thing in, stickers and all. Some stickers darken up, but the Husky stickers don't seem to be affected at all.
@kingsaws
Жыл бұрын
Dude I almost bought one the other day but talked my self out of it
@novicelumberjack
Жыл бұрын
Do it. I've always been a bit hesitant of the Jonsered 2252 because I thought I would never be happy knowing the 550xp mkII was out there. Not anymore. Tonight's Wack-Off will really showcase the torque the porting made with this little 545.
@kingsaws
Жыл бұрын
@@novicelumberjack I'll be watching it
@alexstromberg7696
Жыл бұрын
A 550 would be even better
@Fishinmech24
Жыл бұрын
Nope I’m not impressed with the 550 100% truth. Why we go with the 545.
@robertclifford1099
Жыл бұрын
@@Fishinmech24 What don't you like about it? Narrow power band?
@alexstromberg7696
Жыл бұрын
@@Fishinmech24 the 55p weights the same but more power
@Fishinmech24
Жыл бұрын
@@robertclifford1099 it’s just not the same different power owning a brand new one and a 545 the 545 is in its own world. Much better saw
@Brian-Outdoors
Жыл бұрын
@@Fishinmech24 watch this video of a 550 Mark II with pulling a 32” bar stock and tell me that a 545 is better kzitem.info/news/bejne/qKhm3HtmsKOKopg
@Fishinmech24
Жыл бұрын
Put the 4510 and the 545 up also
@novicelumberjack
Жыл бұрын
That would be brutal!
@Veau88
Жыл бұрын
I told you testing the chinese knock offa would get the views… keep doin it
@novicelumberjack
Жыл бұрын
Got a 660 on the way!
@craigunderwood4353
Жыл бұрын
How much$ for a muffler mod?
@novicelumberjack
Жыл бұрын
I don't do small jobs like that. Far too much time to be worthwhile for me. Try a channel called Southern Firewood. He's a young guy trying to earn a buck and I betcha he'd be interested. He is building me a muffler for my 372 clone saw. I'll show it on my channel when I get it.
Пікірлер: 130