This video helped me out was struggling all day haha thanks
@bryanmcdonough2436
3 жыл бұрын
Thanks a million bro for this video!!! I’ve searched everywhere for a video on how to install the push rods and set timing on that motor and u are the only one I found that actually shows wat to do. After removing the gov on mine the front rod fell out with the cam gear. And I put it back in and thought everything would be fine. Then it wouldn’t crank for shit :/ after seeing this I’m almost certain that the rod isn’t on the valve and that’s the reason it won’t do anything. I’ll find out for sure this weekend but thanks to u, now I know wat to do with that rod so it will work again. I hope this video gets u a million views cuz I’m sure I ain’t the only one with this issue lol
@theperfectpaintertoolreview
3 жыл бұрын
Anytime, it always feels good to know I've helped someone. Just make sure those pushrods go into those lifters, or "caps" as I called them. U may have to look in there with a flashlight as u put the rods in. The camshaft pushes on those lifter and raises the pushes rods which opens and closes this valves. Make sure ur valve clearance is at no more then 3 thousands of an inch of it's a predator 212. Don't listen to the ppl that say 6 or 8 thousands, I bent valves that way before. It'll run as long as ur timing marks are lined up and valve clearance is correct. Also lube all metal on metal with oil or assembly lube. If the motor is gonna sit for awhile after assembling use assembly oil or lucas oil stabilizer, it's much thicker.
@bryanmcdonough2436
3 жыл бұрын
@@theperfectpaintertoolreview hell yea bro I got it that evening. Pulled the valve cover off and both rods were off the valves so that was my issue LOL but I need to go back and set my clearances again cuz I set the exhaust to 5 and the other to 4. My next issue is now fine tuning the knockoff mikuni I put on it, I think it’s gonna need a bigger jet but I’ll get that figured out later, just glad my issue was something simple that I did and nothing major from doing something minor during gov removal, thanks again bro and hope you have a great future in the years to come!! Peace bro!
@theperfectpaintertoolreview
3 жыл бұрын
Thanks bro I appreciate that. Glad to hear u got it running 👍 the factory spec on the intake valve clearance is .003, the exhaust is actually .0025. it'll probably be ok where u have it but I've had the best results with the factory settings unless there is a upgraded cam or rockers or something like that. 3 thousands on both will be fine tho. If the gap is too big the valves will hit the piston. If u lose power at top speed u need a bigger main jet. If it's only running on choke u probably need a pilot/idle jet. U can get a whole kit with both on Amazon for like $10.
@theperfectpaintertoolreview
3 жыл бұрын
Here is one of the kits. Look closely at the holes on the emulsion tube and compare to the one in your carb, make sure they are rite. There are a few different styles that look very similar www.amazon.com/Amhousejoy-10pcs-Carburetor-Pilot-Keihin/dp/B07VPSMKKY/ref=mp_s_a_1_4?dchild=1&keywords=terbel+20pcs+jets+kit&qid=1611416941&sr=8-4
@bozebohz8297
2 ай бұрын
The same thing happened to me takinh off the governor and I cut the throttle return spring to short bro do u think you can make a video on how to do it properly
@fullpinnedvlogz1832
3 жыл бұрын
I did some upgrades on my engine. Would you mind making a vid on how much play the cam should have because mines knocking and it think that might be the culprit
@regain8951
2 жыл бұрын
Hey the same thing happened to me when I was removing the governor and oil sensor. But the push rods didn't fall out and only the cam did. Can I just put the cam back with the holes aligned? Or do I have to do something else?
@theperfectpaintertoolreview
2 жыл бұрын
U can just put it back in but the dots have to matchup perfect
@adamgonzalez2045
4 ай бұрын
@@theperfectpaintertoolreviewdoes the engine need to be TDC? I lined up my timing marks and it still won’t start
@SeanErpelding32
2 жыл бұрын
Does it have to be top dead center before you do all that or they just go before cam and slide right in?
@theperfectpaintertoolreview
2 жыл бұрын
Not for camshaft removal/install. When u turn the crankshaft to pine up the timing marks it will push the piston up. Top dead center occurs every other revolution of the crankshaft. As long as your timing marks are perfectly line up ur good to go.
@norcal8718
2 жыл бұрын
Does that compression release have to hook up to anything or is it like centrifical?
@theperfectpaintertoolreview
2 жыл бұрын
Sorry I'm just seeing this. It is centrifugal. Hope I'm not too late answering your question
@BubbleWayz
Жыл бұрын
Mann I don’t know what the problem with my 212 I did everything right with my push rods it’s on the lifers i set my lashes to .003 I’m making sure I’m TDC IN MY MOTOR STILL WONT CRANK I JUST DONT UNDERSTAND WHST IM DOING WRONG I have spark
@Jayhla1
3 жыл бұрын
Did you have to clearance???
@theperfectpaintertoolreview
3 жыл бұрын
As long as u don't loosen the nuts on top the valves u shouldnt have to, but it's always good to check valve clearance after something like this.
@christiansmith4803
3 жыл бұрын
does it mater witch push rod go in the slot
@xxzeroxgamerxx-6735
2 жыл бұрын
Absolutely not
@toonsszn8418
3 жыл бұрын
Can I just put a new cam in with out changing the valves
@theperfectpaintertoolreview
3 жыл бұрын
Yea just don't touch the valves. When u take out the cam make sure those lifters/caps don't fall out or else the pushrods will fall out also. Then you'll have to take off the valve cover. I would lay the motor down on its side before removing the cam
@theperfectpaintertoolreview
3 жыл бұрын
U don't need to change valves when putting in a new cam.
@toonsszn8418
3 жыл бұрын
@@theperfectpaintertoolreview thanks for the quick response
@theperfectpaintertoolreview
3 жыл бұрын
No problem bro, hope it goes good for u.
@alasdhuntersgaldiano8226
3 жыл бұрын
Nice sir
@theperfectpaintertoolreview
3 жыл бұрын
Thank u
@alasdhuntersgaldiano8226
3 жыл бұрын
@@theperfectpaintertoolreview just visit my house if you like it tnks
@Hoodadventures602
Жыл бұрын
Thank you sir 😎
@christiansmith4803
3 жыл бұрын
Bcause there a aluminum one and a metal on witch one go were
@theperfectpaintertoolreview
3 жыл бұрын
Are u saying u have 2 different pushrods? One is metal and one is aluminum?
@theperfectpaintertoolreview
3 жыл бұрын
On a predator 212 they both should be identical and can go on either exhaust or intake side. U should be able to put them on either side
@bozebohz8297
2 ай бұрын
I didnt align the 2 dots and my mini bike wouldn't start
Пікірлер: 33