Thank you for the clear and concise explanation. I'm looking forward to your next Bently Nevada video.
@jimdiggins101
3 жыл бұрын
Thanks for watching. I am working on an axial thrust installation video.
@ValenBKW
3 жыл бұрын
Thank you for excellent recearch.
@jimdiggins101
2 жыл бұрын
Glad it was helpful!
@athul3459
3 жыл бұрын
Thanks for your explanation and clear information
@jimdiggins101
3 жыл бұрын
You are welcome
@kithtube
9 ай бұрын
Good exlonation jim,thanks.
@chouitala1727
4 жыл бұрын
Thank you very much
@nelsonzhang3996
3 жыл бұрын
Hello sir, we are PLC/DCS company in China. If you need any model, you can contact us. We'll send you a quotation. Whatsapp: +86 18059275924 email: nelson@nseauto.cn
@zahidjummal7709
3 жыл бұрын
@@nelsonzhang3996 which dcs
@JesusEmmanuelGoneCadena-pd2ug
Жыл бұрын
Dear Jim thanks for video, I only have two questions, at the end we obtained values that were out of tolerance, right? And this was probably because we use other extension cable model, right? In advance thanks for your response! And good job!! 🤘
@jimdiggins101
Жыл бұрын
Correct. Incorrect length is the most common cause of error
@jeanoliveira8837
8 ай бұрын
WOULD YOU LIKE TO SEND THE TALEBA FOR SENSOR CALIBRATION
@crunchyrollo7474
Жыл бұрын
Thank you very much for the information, although I have a question, at minute 2:24 you put the value of 1 in the voltage column. why 1? What shouldn't be 10mil*200mV= 2V?
@jimdiggins101
Жыл бұрын
The response rate of 200mV / mil is only valid within the range of linearity. 0-10 mils is outside this range.
@thyagarajanbalachandran7669
Жыл бұрын
Hi this was a very good presentation I request if you could explain how the graph could be configured
@jimdiggins101
Жыл бұрын
I can do that.
@user-hi7rf3bp8h
Жыл бұрын
What do you supply proximity power with? What kind of lines?
@hondat7435
Жыл бұрын
hello, when i connect the power supply 24VDC positive to the com and negative to the Vt(-24 VDC) it creates an alarm on the power supply and shut down the power supply. Please advice on wiring?
@jimdiggins101
Жыл бұрын
Power to com and -24. Output signal to out.
@SuperPhianh
2 жыл бұрын
if ISF% bigger than the manufacturer's standard, how recalibrate?
@ShuhardRedd
Жыл бұрын
Thank you!
@jimdiggins101
Жыл бұрын
Welcome!
@nazimhalim7106
2 жыл бұрын
Good sharing
@engenhariaeletrica-calculodesc
3 жыл бұрын
hello, How did you determine the standard deviation in the table below the graph?
@jimdiggins101
3 жыл бұрын
I no longer have that spreadsheet to check. I believe each value represented the deviation from the expected value for the associated test point in relation to the linear span of the uncontrolled variable. In addition I think I performed a best fit using the "least squares" method (=LINEST) for the collected data, then compared that array with the stated manufacturer's and flagged a fault using conditional formatting if the difference exceeded the stated tolerance.
@kantipudijanakiramayyachow2844
Жыл бұрын
Thanks
@hatemmoussa7467
Ай бұрын
How much is this kit?
@zacktaba1025
3 жыл бұрын
Hi mr Jim, can help me to make this table plz?
@jimdiggins101
3 жыл бұрын
Yes.
@zacktaba1025
3 жыл бұрын
@@jimdiggins101 where can i download this table?
@jimdiggins101
3 жыл бұрын
@@zacktaba1025 It is not available for download. I can help you through email.
@kasumy17
3 жыл бұрын
i can sent the table and how you calculate de sensitivity
@jimdiggins101
3 жыл бұрын
@@kasumy17 My email is listed on my channel.
@TheSonu48
4 жыл бұрын
Nice video sir, sir can you provide this calculator please
@nelsonzhang3996
3 жыл бұрын
Hello sir, we are PLC/DCS company in China. If you need any model, you can contact us. We'll send you a quotation. Whatsapp: +86 18059275924 email: nelson@nseauto.cn
@djallildjalil1400
3 жыл бұрын
The test of linearity check is for proximetor or for the probe !?
@jimdiggins101
3 жыл бұрын
Probe, cable and proximitor. If you leave it connected to the card, it will also verify the monitoring rack and associated wiring.
@shinethilakan9491
2 жыл бұрын
@Jim Diggins Hi brother..Could you pls share a copy of the excel sheet if you dont mind. Will be really helpful..
@jimdiggins101
2 жыл бұрын
Sorry, I can't. That is why i uploaded a video showing how to make in excel. Follow along and you should be able to make one for yourself. If you run into problems let me know.
@kasumy17
2 жыл бұрын
i can sent it to you, if you send me your email
@amitbatliwala577
Жыл бұрын
@@kasumy17 please share to me amit.batliwala@gmail.com and amit.batliwala@inoxap.com
@karthikdhandapani1264
3 жыл бұрын
I AM TRY TO PREPER SPREED SHEET/ DEVIATION FROM STANDARD 2.19% HOW UR CALCULATING IN GRAPH BALANCE ALL DONE and graph model i cant get in excel
@jimdiggins101
3 жыл бұрын
I run two deviations simultaneously. One is a total slope deviation and one is a deviation in scaling factor. The most important one is the scaling factor deviation. For that one, you calculate the voltage difference (D) between test interval (A) and (B) (A-B=D). Then determine the deviation from the rated ISF for the given test point(ISFD), (D-ISF=ISFD). That difference is then divided by the rated ISF. The formula to this point is ((A-B)-ISF)/ISF=X percentage of deviation. Here is an example using a 200mV/mil (2volt/10mil) product with the following test interval..20mil=3.1Volts and 30mil=5.2Volts. (5.2-3.1)-2=0.1 0.1/2.0=0.05(5%deviation). The percentage of deviation on the total slope runout is performed by building a linear slope and comparing each individual test point to the shared location in the slope. As an example: An ISF of 2V/10mil starting with 1V@10mil would create a projected value of 9volts at 50mils. Your actual measured value at the 50mil test point can be compared to 9volts to create a percentage of slope change. This deviation value is not as important in vibration because the distance between the shaft and probe is not as important as the continuous change in voltage between the shaft and the probe. It is complicated to put in typing, hope it helps.
@karthikdhandapani1264
3 жыл бұрын
@@jimdiggins101 thank you for ur reply ,it very help full for me
@karthikdhandapani1264
3 жыл бұрын
@@jimdiggins101 can share ur e mail Id i will send u which i prepared spread sheet for your feed back, if possible karsta_kar@yahoo.co.in ,thank you
@jimdiggins101
3 жыл бұрын
@@karthikdhandapani1264 My email I'd is shared on my channel.
@nelsonzhang3996
3 жыл бұрын
@@jimdiggins101 Hello sir, we are PLC/DCS company in China. If you need any model, you can contact us. We'll send you a quotation. Whatsapp: +86 18059275924 email: nelson@nseauto.cn
@danperrin6441
2 жыл бұрын
Hi Jim, great video. Is the spreadsheet something you can send over email if i provide you an email address. I understand you have made a video to show how to generate one of ourselves but would appreciate if i can get this off you.
@jimdiggins101
Жыл бұрын
Sorry, I cannot.
@zahidjummal7709
3 жыл бұрын
Can u please share spread sheet on my mail id,
@jimdiggins101
3 жыл бұрын
I can send you the spreadsheet if you provide your email address. If you are interested in making your own, I published A video with instructions.
@zahidjummal7709
3 жыл бұрын
@@jimdiggins101 OK send
@jimdiggins101
3 жыл бұрын
@@zahidjummal7709 Where do you want me to send it to? Your email address is not listed on your page.
Пікірлер: 71