Vibration monitoring thought to be most complex but you made it simpler. Thanks
@jimdiggins101
3 жыл бұрын
Thank you for the compliment!
@siyabonga6156
10 ай бұрын
Very good explanation, now I have a better understanding of Proximity probes.
@s0nnyburnett
7 ай бұрын
Simple to the point explanations, thank you.
@diamondraj3868
2 жыл бұрын
very good ,explained clearly thank you sir.
@jimdiggins101
2 жыл бұрын
Thank you for the kind words.
@arunswamidasan537
3 жыл бұрын
Continue upload videos, It's so informative .thank you
@jimdiggins101
3 жыл бұрын
Thank you, I will
@bestofwagar7777
3 жыл бұрын
Excellent explained.... great job...
@jimdiggins101
3 жыл бұрын
Thank you!
@kithtube
2 жыл бұрын
Awesome instruction.
@jimdiggins101
2 жыл бұрын
Thanks
@muhammadrizwan1223
3 жыл бұрын
out class presentation...God bless you
@jimdiggins101
3 жыл бұрын
Thank you friend!
@indranag1965
3 жыл бұрын
I got great information... Tq brother
@jimdiggins101
3 жыл бұрын
I'm glad you liked it, thanks for the feedback.
@Blades-fm6ck
2 жыл бұрын
Great, clear explanation. Excellent.
@jimdiggins101
2 жыл бұрын
Thanks!
@divyangpatluwala7425
2 жыл бұрын
great video..thanks a lot
@CATips
3 жыл бұрын
Nice explanation
@jimdiggins101
3 жыл бұрын
Thank you!
@noceng7686
2 жыл бұрын
thank you God bless you, that was great
@jimdiggins101
2 жыл бұрын
Glad you enjoyed it!
@afs6884
2 жыл бұрын
Bom dia, muito bom o vídeo obrigado vai me ajudar muito no trabalho!!
@djb4programming
Жыл бұрын
Thank you
@jimdiggins101
Жыл бұрын
You're welcome
@asadiqbal87
2 жыл бұрын
very informative
@jimdiggins101
2 жыл бұрын
Thank you.
@cavourmartinelli9381
4 ай бұрын
Simple explanation, but hard to find it. Do you know any supplier I can buy proximeters from? I am located in Brazil.
@jimdiggins101
3 ай бұрын
I don't know. Baker Hughes owns Bently Nevada and they have a global presence. I'm sure there is a local representative. I would check their website.
@xrafter
8 ай бұрын
How does the eddy current generate in the metal? Does the varrying magnatic field has something with it?
@jimdiggins101
8 ай бұрын
You are correct
@trinhminhkhoa1969
Жыл бұрын
Thank you for your video. I have a confused question " Can vibration monitoring module supply +24VDC and -24VDC ?"
@jimdiggins101
Жыл бұрын
Are you referring to the proximitor card on the bently nevada monitoring rack?
@trinhminhkhoa1969
Жыл бұрын
@@jimdiggins101 Yes, Sir
@husseinjavan-bg6sv
10 ай бұрын
Dear sir. I have two probes with different part number, PN: 86691-08065-0435-25 and PN:86691-09246-0435-25. I only know they are 2.5 m length but i am not sure they can be used interchangeably. Is it possible? What are their differences?
@jimdiggins101
9 ай бұрын
I don't have that manual, so I cannot say for certain. From a performance standpoint it should work. Difference will be in the custom features. Such as mounting options, length of armored jacket, etc..
@syedaslam2856
3 жыл бұрын
Can we do the adjustment in proximitor like we do in transmitters
@jimdiggins101
3 жыл бұрын
You cannot adjust the proximitor. This is because there is no scaling taking place inside the proximitor. This function occurs at the monitoring rack. Good question.
@SuperPhianh
2 жыл бұрын
if ISF% bigger than the manufacturer's standard, how recalibrate transducer?
@jimdiggins101
2 жыл бұрын
This procedure verifies accuracy. You must determine the amount of acceptable error based on machine tolerances. Excessive error usually indicates a mismatched or faulty component. The resistance test can help diagnose.
2 жыл бұрын
At 3:13, what is actually the neutral point of the oscillation ? Is it the initial gap voltage when the shaft stops spinning or when there is no vibration ?
@jimdiggins101
2 жыл бұрын
The neutral point is the mid point between upper and lower travel during vibration. If the shaft is not vibrating, there is no neutral point because the voltage is not fluctuating. Or are you asking what the expected DC voltage will be during vibration?
2 жыл бұрын
Thank you, I got your point. But what can we do with the DC voltage when the shaft is vibrating, or we just care about the AC voltage and use it to calculate frequency & amplitude of the vibration ?
@jimdiggins101
2 жыл бұрын
@ DC voltage is still used in Radial Vibration. Most people track DC voltage and set alarm points to warn if a probe is out of range. It can also used for measuring shaft movement while it is rotating for diagnostic purposes. Bearing wear can cause shaft drift over time, which can be identified with gap voltage while it is running. Pressure dam bearings cause the shaft to ride on an oil wedge. Radial vibration probes can monitor this shaft movement with the gap voltage. This is why it is important to set all probes at the exact same voltage so you can monitor movement across the shaft length.
2 жыл бұрын
Thank you. I learned alot.
@agusgimbuk8365
Жыл бұрын
Excuse me sir. My name is agus. I have some question related with vibration system. 1. Whats the function for minus DC power supply? 2. Whats correlation between DC power supply and AC power supply which generated by probe?
@jimdiggins101
Жыл бұрын
Answer 1: The polarity doesn't matter unless you are a transistor, which in this case is why the polarity is reversed. For the purpose of understanding how it works, it makes little difference.
@jimdiggins101
Жыл бұрын
Answer2: Think of the AC as DC with a wave. Normal AC changes polarity, this doesn't. You just have to switch a meter to AC to measure the dynamics of the sinewave that is created. It's AC with a voltage bias.
@arjunkulshrestha78
2 жыл бұрын
The supply given is -24 Volts. Why not a positive supply?
@jimdiggins101
2 жыл бұрын
This product was originally invented a long time ago. At that point in time, due to the availability of semiconductors, it was more practical and cost efficient to apply a negative voltage, which provided the proper gate voltage for the more common semiconductor type. It is no longer a thing that people consider during instrument design. The -24volts has been adopted by all the newer iterations of the product line.
@Jokesxxl
2 жыл бұрын
Great video! How do you put in and out the override switch? Normally this is via the monitor software?
@jimdiggins101
2 жыл бұрын
I'm not familiar with an override. Are you referring to the bypass switch?
@Jokesxxl
2 жыл бұрын
@@jimdiggins101 in between i figured out, every slot has a digital input alarm. At our plant we can override with a switch the DI!
@kasumy17
2 жыл бұрын
@@Jokesxxl you mean, trip multiply??
@Jokesxxl
2 жыл бұрын
@@kasumy17 i looked further, i mean a override switch for alarm if you replace a sensor
@kasumy17
2 жыл бұрын
@@Jokesxxl okay, you mean bypass the alarm, while you replace de sensor during an operation machine??
@agungandritzson2736
3 жыл бұрын
Jadi ini sensor proximitor atay vibration mas. Maaf masih awam
@idontknowidonrknow4622
2 жыл бұрын
Hello, this video was very useful. How can we contact with you?
@jimdiggins101
2 жыл бұрын
I have my contact information listed on my KZitem page. Thanks for watching.
@kasumy17
2 жыл бұрын
sr. if you need more info about it, i can send it to you,
Пікірлер: 67