I am VERY fussy on who works on my bikes, operates my bikes, and who even rides on my bikes. But I can tell you it would be an honour to have this man work, operate,and ride on my bikes. D-Ray is not only a great mechanic, but the respect he has for customers machines is amazing. THAT is rare now adays! D-Ray, keep up the great work sir.
@justatool
10 жыл бұрын
D-Ray, Thanks again, I soaked low speed Jet in mineral spirits for 5 minutes, and since I didnt have a jet cleaning tool I used a needle to loosen any junk down in the jet, For the first time I was able to see light through this jet, now is idling perfect and sounds great! There is a 35 stamped on this jet so if anyone is looking for that info thats what size of jet cleaning rod to use!
@beastnsuwoop9974
5 жыл бұрын
So the hole does go all the way through? Dang no wonder my Honda doesn't start.
@Tr6e9nT
11 жыл бұрын
Truly a work of art dismantling and rebuilding. I had my 1985 200x carb out and followed your instructions, excellent results. Ran it 20 min after rebuilding flawlessly. I did have an issue with a dirty spark plug but a wire brush and bit of sand paper did the trick. Saved me from cretin doom my friend. Keep up the great work, and thank you for your knowledge.
@whathappened2230
26 күн бұрын
Thanks D-Ray! Just what I needed!
@loganpardon
11 жыл бұрын
DRay i don't know you. But YOU ARE AN AWESOME MECHANIC. You just saved me hundreds of dollars on labor by a shop. I acquired a 1894 ATC 200m a few days ago that was in great shape and would start and run, but had some problems and needed refreshing. I performed and copied everyone of your videos on the 200s when repairing my ATC. It runs and performs AMAZING now. You also do incredible camera angles when showing things and i can hear you amazing. MY HAT IS OFF TO YOU.
@InTheFleshInc
2 жыл бұрын
Just watched your other video and commented didn’t realize these are nearly a decade old videos wow
@MrMojoDiver
4 жыл бұрын
Great video, and made putting the carb back together less of a pins/needles affair. Also great tip on turning the pilot needle in and counting the revolutions til it snugged up.
@nathanenglander6496
5 жыл бұрын
Thanks so much bud. Very well explained. Had my 84 200 up and running in 30 min. Now I'm heading out into the snow to pull my daughter around in her toboggan. That's is again from the both of us :)
@walkerdb84
Жыл бұрын
Thanks for sharing, watched your videos and was able to get my 1991 Honda Fourtrax 200 going again in a short amount of time!
@raysanguinetti7208
Жыл бұрын
The reason I watched this vid is I’m prepping to do a carb rebuild on a 1991 Honda Fourtrax 200 TRX. Is this the same carb on our machines? I cannot find any info on KZitem regarding carbs for our machines. Thanks for any info you can provide. Ray
@williamshovlin3383
9 жыл бұрын
Thank you, thank you, thank you. Your video made my carb cleaning project so much easier. I just want you to know that your efforts are very much appreciated.
@3rdofthree
5 жыл бұрын
I hope I have thanked you before for these videos, but if not: Thank You for the diligent efforts you put into your videos! Great work!!
@XEROXUc3NiTzmEtO
7 жыл бұрын
Dude thank u so much this helped me for my 1986 honda fat cat rebuild for me and my dad and brothers dude thank u so much
@Mc88Flyy
4 жыл бұрын
Thanks! I'm cleaning my carb on my 87 Honda Fatcat. Hoping it'll run after this.
@kaszubmat
11 жыл бұрын
Your the man! Thanks for teaching me! Matt 1979
@williammartineau5130
11 жыл бұрын
thanks D-Ray I am working on my 84 200s and your vid are so helpfull thank you!!
@DRaysShop
11 жыл бұрын
Up is full choke, down is off. Sounds like your Idle circut is plugged, probably the idle jet. Make you a little hook tool from a small piece of wire like I did in the video, you may find the washer and o-ring stuck in the carb. It does really need those two items to run right, or it will pull air from around the threads of the mixture screw and not idle consistantly. Thanks for watchin'.
@DRaysShop
11 жыл бұрын
Sounds like you either have a stuck bystarter plunger and or a plugged low speed jet. Thanks for watchin'!
@fredhead5834
4 жыл бұрын
I have A 1984 ATC200s You have a video on the fireing mine want fire thanks brother for these vids .
@brentsimonson6403
8 жыл бұрын
Great videos!, I have the exact same model in almost as good of shape. Gas was pouring out of the carb and with the help of your video it is running great. It even idles perfect without having to keep pressure on the throttle,lol. Thanks for the help, you saved me a lot of headache!!!
@carlsaiyed1097
5 жыл бұрын
Thanks for posting this.
@natewalton3542
3 жыл бұрын
Great information
@jennifercharlton-dennis6763
8 жыл бұрын
I can't tell you how helpful your videos have been man!!! Thanks for making them!! We have an 84 200s so these have been great!!! I successfully changed the recoil rope on ours because of these!! You have any plans for work on the 110s? Thank you again man!
@TheN3tT3chMan
8 жыл бұрын
great videos helped us out a ton. Thanks!
@dwayneguydammit
11 жыл бұрын
fantastic video! thanks for posting this!
@Kerrage
10 жыл бұрын
easy way to remember is down to ride around
@matthewstonerock5051
8 жыл бұрын
Awesome video really helped
@rotorav8
Жыл бұрын
I’ve been looking for what goes in the mixture needle hole for hours online trying to figure out what goes in first. It must be the o-ring then washer before the spring. The diagrams aren’t real helpful since they don’t label the washer and o-ring and the pics are blurry. Thanks for the video!
@oKarrot
9 жыл бұрын
Those mini slip joint pliers really caught my eye! Where did you get those? Great videos by the way!
@DRaysShop
9 жыл бұрын
Kyler Diaz Thanks! I got those pliers years ago from matco
@riclulua5813
9 жыл бұрын
How do you replace the rear brake shoes? I have a big red 200CC and have no breaks anymore. Would love to see a video on that. Great Videos. Thumb up here.
@bobhunt3197
8 жыл бұрын
+Ric Lulua Pull the brakes apart and have a look, there very simple three moving parts.
@tomlibby9105
10 жыл бұрын
does the low speed jet have a hole that goes all the way through,not the holes through side of tube but is there supposed to be one all the way through the middle?please help as i cant seem to get any of my jet cleaners to go through the middle hole.
@beastnsuwoop9974
5 жыл бұрын
I'm wondering the same thing I guess its really small and yes it goes through all the way. I think that's why I'm not getting fuel through the carb either. That guy that commented said he used a small needle
@jerrywhatsworth3589
5 жыл бұрын
Torch tip cleaners work very well and are very inexpensive compared to the Honda
@romancollins6065
11 жыл бұрын
Very helpful. Thank you for making this video. God bless your soul good sir! :-)
@1better831
3 жыл бұрын
Great Video. Thank you for your work. One question. When I took my carb apart the first time it had been sitting for 15/20 years and was very dirty. I’ve got er cleaned up but when I went to put the main jet in it seems to bottom out before it seats against the housing. Could it be that the nozzle is up side down and stopping the main jet from seating? I didn’t notice it wasn’t sitting right when I took it apart due to the crud. Also I’m having trouble getting the nozzle out so it wonder if it was squished in there when they tightened the jet. Any help is greatly appreciated.
@dionsmith5228
4 жыл бұрын
Good Afternoon D-Ray from CANADA EH... I have a Honda 1984 ATC 200m I am trying to get started... I followed your steps EXACTLY but I have fuel dumping out the drain valve and the one on the side... Plus it will not stay going unless the choke is on "FULL". It idles like a champ but I am not clear where I went wrong... Any thoughts sir?
@justatool
10 жыл бұрын
I think you answered the question at 3:40 I guess I need to know what size of jet cleaner to use thanks!
@shanebissell8571
11 жыл бұрын
DRay - Great video. I have an 83 Big Red 200 (my dad has had this since new and has been sitting dormant for 15 yrs). By the looks of things the carb is identical to that in your video. When I removed the low idle mixture screw, I found the washer and o-ring but there was no spring! Funny thing is the washer was gummed to the bottom side of the threads..as if there used to be a spring there. Could it have rusted/disintegrated? Or is it possible there was never one there? Thanks!
@johnclark2941
4 жыл бұрын
Same yr 1984
@justatool
10 жыл бұрын
Thanks for all of your videos on this Bike. I have a Question on the low speed jet, what size of jet cleaner do you use on this one? or do you even use a cleaning rod at all? I took mine out and soaked it, blew compressed air through it, but never saw daylight through the shaft, it does have some smaller holes near the end and those are all clean. The bike runs and I have to give it quite a bit of gas, just doesnt want to seem to idle! help appreciated!
@calebdavidson1405
10 жыл бұрын
D-Ray, I have a question for you....what exactly is the jet bonnet for/its function? Is it necessary to have in the carb?
@KENPOCHOPPER
3 жыл бұрын
I just picked up a 200 S 1985. When you move the machine forward the rear brake automatically Locks up. When you wheel it backwards it frees up. Not sure why? It also looks like there is a compression lever on the side of the motor but there's nothing attached to it wondering if I can find someone somewhere online to hook up to it? The front brake lever is missing but the cable is there. We'll have to do a search online to find parts. If any suggestions would be appreciated
@goadmerle
2 жыл бұрын
I just got an 84 200s project. And i noticed this carb looks new. Its a mikuni carb. But does not have the fuel bonnet inside. So not sure if its the correct carb. Bike wont start. And when i pull the rope while choking it with my hand. It pours fuel out the barrel. Could that be the cause of the missing fuel bonnet? Or do they make carbs without them?
@trentonkorbel9129
8 жыл бұрын
nice video! I cleaned my 200s carb and u ran into a big issue, I got it all together and all it started but when the rpms get high it dies and sounds like complete crap, any suggestions?
@zmurray9499
4 жыл бұрын
Hey D-ray there is no way to replace the seat? I am still having problems with it flooding after needle and float replacement. Thanks
@edwardkostikjr896
8 жыл бұрын
I just pulled my carb apart and found that there is no O-ring and washer under the idle mixture screw. All i can see inside is a tapered seat. The carb was working but would only run well with the choke on. Is it possible that my carb may have never came with the o-ring and washer or was is incorrectly assembled by the last owner?
@jakeringelstetter2563
2 жыл бұрын
So my carb doesn't have a washer/oring on the air fuel screw. Can that cause a problem with running too rich or fouling out the spark plug?
@beastnsuwoop9974
5 жыл бұрын
That slow speed jet.does the hole ho through it?I tried to clean it but it doesn't look like the hole in the middle goes all the way through ?
@80srockerable
7 жыл бұрын
I used the smallest guitar strings (B & E) to clean out those fine holes of the jets out. Worked good. Do you know if that "main jet" plastic funnel piece thing is designed to fit just fits loosely to the stem or should it be snug? Mine will fall off. Wasn't sure if my carb cleaner ruined it.
@dylansprague8065
3 жыл бұрын
Cleaned mine like 4 or 5 times because of the rust in the tank and 6 months later my one wont stay on and its making it flood and runs like shit with it off. What did you end up by doing with yours mate?
@80srockerable
3 жыл бұрын
@@dylansprague8065 its been a long time. I don't recall. I most likely ordered a new one from Honda dealer. Or you can online. Seems like I recall buying an entire carb rebuild kit through a dealer. It was aftermarket though like maybe Moose brand. These are available Online and come with many parts and gaskets. You don't have to use all. But the kits are cheaper than buying individual parts.
@stevealaska73
8 жыл бұрын
D-Ray, I have an urgent question for you. Please answer as soon as you possibly can. I just cracked open my 83 200x's carb and the bowl and entire inside was horrible. There is no main jet bonnet. It may have been among the gunk that appeared to be shredded leaves at the bottom of the bowl. How important is this bonnet part? Can I get away with not using one? Or should I order one? Also, do you have a recommended parts source?? Thanks in advance!
@adamchevrefils8861
7 жыл бұрын
Funny because I opened up my carb to find there was no jet bonnet as well. How did it workout? Did you run the carb without? or did you go out and get another? Thanks.
@andrewcranmore1477
9 жыл бұрын
I have a 1983 atc 200 and it's pouring gas out of the over flow and can't figure out why any suggestions I also seen in this video that the carb only had 2 fuel li nes coming off of it mine had 3 one comeing from the tank and 2 coming off the carb going to nothing is that correct?
@ATwiztidNiNjA
2 жыл бұрын
How Important is the main jet holder or jet bonnet like you called it? Does anyone know?
@jerryjones1056
3 жыл бұрын
What makes my 1983 200e big red very hard to start on cold weathet.
@Day12My
Жыл бұрын
I'm confused. My low speed jet doesnt have a slot for screwdriver, just a hole and it doesnt screw in. It just pulls out....IS this normal?
@johnclark2941
4 жыл бұрын
Is the atc 200sx like the trx200 four wheeler?
@coleszekeres6936
6 жыл бұрын
D-ray this is urgent I have a 1982 Honda ATC 185s and in neutral and 1st gear it has either zero throttle where it doesn’t run or full uncontrollable throttle how do I fix this
@158mollie
11 жыл бұрын
Hi,what type of gas to use in a older atc.i was thinking plus.I use in my 84 XT 600 dirt bike plus or higher.
@dustydragon420
11 жыл бұрын
I have a 250es Big red and when I first start it I have no Idle once it warms up it revs really high any comments?
@xavierlange8876
6 жыл бұрын
This a keathen carb I have a 85 200x and I took the plug out and it was black what do u recommend doing
@iphonemodder1
11 жыл бұрын
is it bad to not have that last plastic part? I lost mine on my 1982 185S
@johanycastellonreyes745
8 жыл бұрын
Hola Este carburador le sirve a una moto freedon 200 cc
@emmanuelfernandez5840
8 жыл бұрын
where does the drain tube for the carburetor go to?
@mrsmilly12345
11 жыл бұрын
i might get a 200s how do i drive it when do i know to shift up? or down and is 300 a good price for a 200s atv
@kikidelacroissant7183
5 жыл бұрын
Any diff with the carb on a big red same year?
@iraginrabbit80
11 жыл бұрын
DRay- I just bought an 85 200s. I haven't owned an atc for over 15 years. I can't remember the choke positions and am unable to find a reference. Is down full choke, up off? The main problem is this ATC runs great with half choke, when I flip the choke up it dies instantly. I took the carb apart today and the everything checks out great except the pilot jet doesn't have the washer and gasket at the end of it. Is that a huge problem? The valves seem snug, and the timing looked ok.
@danieldollar6280
9 жыл бұрын
Do u no how to adjust valve on honda 300 fourtrac atv
@flintsmiley9595
4 жыл бұрын
What if there is no bounet?
@andrewcranmore1477
9 жыл бұрын
also I'm not getting any fuel to the plug the atv will fire with starting fluid but dies seconds later any suggestions will be greatly appreciated
@daviddc7906
4 жыл бұрын
Andrew Cranmore make sure your float is set at the correct hight and make sure your pilot jet the little one is the correct size if so make sure the main jet is the correct size. That should fix your problem
@laurajeddry556
11 жыл бұрын
cleaned the carb ,and now gas pours from the overflow and out the side please help
@kikidelacroissant7183
5 жыл бұрын
Five years late you missed something in the float and needle most probably the seat
@tylermarini9683
9 жыл бұрын
I have a carb of my own and I've cleaned it several times and it continues to overflow with gas I was wondering if anyone had a solution for this problem?
Пікірлер: 84