Your video helped me A LOT I have Science Olympiad and, had no clue how to use this, your video helped a TON
@christhedemocrat
11 жыл бұрын
My friend is a Q/C guy and he brags on his job a lot but that ish is so simple. In 4.25 minutes I feel like I'm a pro already. I looked up how to use a caliper and that one was just as easy. Wow Im an electrical technician/foreman ...Maybe I need to change fields. Great video by the way . Im gonna put what you've taught me on my resume'...lol
@glenfenderman
11 жыл бұрын
Thanks for posting that. I'm taking a small engine repair course, and the textbook didn't explain that clear enough for me. You helped me get over a hurdle!
@shammaal-kaabi9524
10 жыл бұрын
I'm taking a Physics Lab course, and I had to use the micrometer several times and never really knew what I was doing. I've got my Final this Wednesday and I should say, I mastered reading the micrometer thanks to your video! Thanks a lot it really helped! very simple and clear!
@machiningmoments
11 жыл бұрын
My pleasure, I hope it was helpful. Thanks for stopping by!
@machiningmoments
11 жыл бұрын
My pleasure, thanks for stopping by!
@machiningmoments
11 жыл бұрын
I'm glad it helped thanks for watching and taking the time to post!
@harleypiper
12 жыл бұрын
just found a job at an aerospace co. and they told me about you.I see why.good video sir.
@machiningmoments
11 жыл бұрын
Your very welcome, thanks for stopping by. Good luck with your test!
@pallaviazazelpolarizer2150
11 жыл бұрын
THANKS A TON!! U EXPLAIN WAY BETTER THAN ANY OTHER PHY TEACHER I HAVE! THANKS AGAIN! :)
@machiningmoments
11 жыл бұрын
Any zero error should be adjusted out or calibrated. The sleeve can actually be be turned to adjust the zero for an error. Good luck on your test and thanks for your post.
@machiningmoments
11 жыл бұрын
Thank you for taking the time to watch and post!
@abhinavbajaj3101
13 жыл бұрын
Good work I like the way you teach us patiently
@machiningmoments
11 жыл бұрын
Glad it helped, thanks for stopping by.
@machiningmoments
12 жыл бұрын
It is called a "ratchet stop" it is meant to slip at a set pressure so everyone has the same measuring pressure.
@machiningmoments
11 жыл бұрын
I'm glad it helped and I really appreciate these notes, thank you.
@ChickRollercoaster
11 жыл бұрын
deffinitly, helped me to understand without any confusion, for my practical xams due 2morrow.
@machiningmoments
12 жыл бұрын
There is 12.5mm on the sleeve and .20mm on the thimble so 12.5 + .20 = 12.70mm. Your english is fine. Thanks for your post and good luck with your test.
@machiningmoments
11 жыл бұрын
Proper measuring pressure is set by clicking the ratchet stop.
@machiningmoments
11 жыл бұрын
Your welcome, thanks for stopping here.
@DamianSupra
11 жыл бұрын
thanks a lot I forgot all about this and you just explained it real good and quick :)
@machiningmoments
12 жыл бұрын
I'm glad you enjoyed the video and thanks for your post...I'm not sure what you mean about download.
@machiningmoments
11 жыл бұрын
My pleasure glad it worked for you. Thanks for posting!
@machiningmoments
13 жыл бұрын
@RyersonRobert Would a text box beside the measurement help with what you are looking for? That would be easy to do with the existing video. Thanks for taking the time to leave a message.
@machiningmoments
12 жыл бұрын
I'm glad it helped, good luck with your test!
@machiningmoments
11 жыл бұрын
No worries, it is nice to hear from you. Yes this is a vernier (because of the scale) caliper. Good luck with yopur Olympics and thanks for posting!
@machiningmoments
11 жыл бұрын
:) glad it was useful for you. Go easy on your friend, Q/C guys are important. Thanks for the note and good luck with future job hunts!
@thisissoeasy
12 жыл бұрын
As usual - beautifully explained! Thank you very much.
@nicholasdavis8159
8 жыл бұрын
Great video 100% correct and to the point
@machiningmoments
8 жыл бұрын
Glad you liked it, I appreciate your comment.
@mandarjoshi6814
11 жыл бұрын
Thanks man only one videos for Micrometer Screw Gauge
@machiningmoments
11 жыл бұрын
I'm glad it helped, good luck tomorrow! Thanks you for your note.
@machiningmoments
11 жыл бұрын
Glad it helped, thanks for your comment about zoom and your post.
@machiningmoments
11 жыл бұрын
I'm glad it helped, thanks for letting me know!
@machiningmoments
12 жыл бұрын
@sahilkapur312 Glad it helped...thanks for the compliment!
@thecometgamer4266
11 жыл бұрын
Also, Fun (ish) Fact: I like this type of caliper better than the other type ( I think its called virneier ) because the other type sometimes gives me "paper" cuts.
@yeris.6177
10 жыл бұрын
Congrats man, u literally saved my life in my physics practicum, the teacher was talking so fast, I owe you 1
@machiningmoments
10 жыл бұрын
I'm glad it helped, I hope you do well on your practicum.
@yeris.6177
10 жыл бұрын
machiningmoments i got 85%/100% thanks man
@machiningmoments
10 жыл бұрын
Good for you! My pleasure.
@machiningmoments
11 жыл бұрын
My pleasure glad it helped.
@machiningmoments
13 жыл бұрын
@RyersonRobert Hello again, I went back and checked my vid (forgetful, old age)...the "annotations" are there indicating the measurement. Is it possible you have your annotations turned off? If so go into Settings. I have the same issue you have growing up in the inch system but metric really is easier (and a smaller unit which is ideal for a machinist). The base 10 system makes much more sence than inches eg. 25.4mm is 2.54cm move the decimal. Are you at Ryerson? Thanks for the note.
@machiningmoments
11 жыл бұрын
Glad it helped, and thanks for your post. Good Luck!
@machiningmoments
11 жыл бұрын
I'm glad it was helpful, thanks for posting!
@machiningmoments
13 жыл бұрын
@MartinezMKD Good for you! If you answered that many sounds to me like you know your stuff! I'm sure you did well. Knowledge is power!
@machiningmoments
11 жыл бұрын
My pleasure, thanks for your post!
@machiningmoments
11 жыл бұрын
Glad it was helpful, thank you for your post.
@TOMA21207
11 жыл бұрын
Great vid. Thanks, helped me a lot.
@machiningmoments
11 жыл бұрын
My pleasure, thanks for your post.
@machiningmoments
12 жыл бұрын
Glad it helped, thanks for your post!
@Ashfirephoenix
11 жыл бұрын
very clear explanation...really helpful!
@machiningmoments
12 жыл бұрын
Wow, that is a nice comment! Do you mind if I ask what part of the world you are in? Thanks for thaking the time to write.
@machiningmoments
11 жыл бұрын
Glad it helped thanks for letting me know!
@machiningmoments
13 жыл бұрын
@MartinezMKD Glad it helped, hope you do well on your exam. :o)
@thecometgamer4266
11 жыл бұрын
P.s. I would've failed on my competition next week without you. :)
@ARYANJANAkrishnan
11 жыл бұрын
WOW....IT REALLY HELPED ME
@machiningmoments
13 жыл бұрын
@RyersonRobert Glad it worked for you, I'm at SAIT.
@sarahhazell5777
9 жыл бұрын
I LIKE THIS VIDEO .IT HELPED ME UNDERSTAND SO MUCH MORE THE READING IT.
@machiningmoments
9 жыл бұрын
Sarah Hazell Hi Sarah, I'm glad it helped. Thanks for taking the time to leave a message.
@tushtitiwari3213
6 жыл бұрын
Thank you for explaining nicely
@machiningmoments
6 жыл бұрын
Glad to help.
@machiningmoments
12 жыл бұрын
@XLilmisssunshinE53X I'm glad it helped, thanks for the note.
@shiinax1
12 жыл бұрын
Thanks so much! THis video helped!
@machiningmoments
11 жыл бұрын
Are you having trouble reading the mic?
@pattyfur
12 жыл бұрын
Thanks a lot. This will help me in my Physics lab test~
@MrCcysio
11 жыл бұрын
Thanks! It helped me a lot.
@Tigerlui531
12 жыл бұрын
what does the end of the caliper do? The twist clicking thing
@machiningmoments
12 жыл бұрын
Download button?
@kiotik96
12 жыл бұрын
1 person though dislike was for download ;) amazing video
@mrsech0825
11 жыл бұрын
Thank u. Learned now time to apply
@FazalFariz
7 жыл бұрын
Wow, that's the easiest way I've learned anything. Thank you.
@machiningmoments
7 жыл бұрын
Thank you for your kind words.
@angeldencarmaeliacagasan6888
9 жыл бұрын
Nicely done🙌
@machiningmoments
12 жыл бұрын
@shiinax1 Glad it helped, thanks for the note.
@MyAlexpunk
12 жыл бұрын
WAW!!! DUDE IT WAS AWESOME......
@machiningmoments
11 жыл бұрын
Your welcome, I think? Thanks for your post!
@nevadascott3751
9 жыл бұрын
Never use this type of tool before it looks very interesting would like to learn more about it
@machiningmoments
9 жыл бұрын
Nevada Scott Probably one of the first tools a machinist will add to their toolbox. The standard version is capable of measuring one third of a human hair.
@Gero141
10 жыл бұрын
Thanks. Helped me alot
@gonitya
11 жыл бұрын
thanks a lot .. ! i am sure i will do well in my tests now !
@machiningmoments
12 жыл бұрын
My pleasure
@mohammedibrahim5597
11 жыл бұрын
wow you people are good rabbis.....thanks for your information anyway
@user-tb7nx4em5b
11 ай бұрын
why is no one talking about how he didnt round down to .19 on the sleeve instead of going to .2?
@machiningmoments
12 жыл бұрын
Good!
@hinamori64
12 жыл бұрын
thank you sooo much 2morrow i have test and it will help me but i didnt understand the last part very well it is 12.5 and .20 so you add them, you added like this 12+5+20 this 5 is from 12 right or wrong.............thx and forgive me if my english is bad i am not english.
@pinokosthewife
11 жыл бұрын
Thank you very much for this. ^^
@sahilkapur312
12 жыл бұрын
DUDE your fucking awesome! thanks a million!
@mightydeathlash2867
8 жыл бұрын
Is it indicated on the micrometer that the readings are in millimeters? At first glance it looks like any micrometer measuring in inches D: I feel like there should be some indicater for the unit the micrometer will be measuring by.
@machiningmoments
8 жыл бұрын
At the bottom of the frame it should tell you if it is inch or metric.
@kje0566
8 жыл бұрын
Mighty DeathLash it's units of mm.
@rameshanjelo5320
12 жыл бұрын
cool guidance
@machiningmoments
12 жыл бұрын
Thank you
@divakarmishra6759
7 жыл бұрын
This is very helpfully for me thank you
@machiningmoments
7 жыл бұрын
Glad it was helpful, thanks for the note.
@arafathshiyam
10 жыл бұрын
Thanks helped me alot ! :)
@machiningmoments
10 жыл бұрын
I'm glad it was useful, thank you for watching!
@gonitya
11 жыл бұрын
how to calculate the zero error ?
@tamannachhetri3836
10 жыл бұрын
Well explained! Thanks
@machiningmoments
10 жыл бұрын
Glad it helped, thanks for your comment!
@jsarangi
12 жыл бұрын
very nice...
@ScoutSniperTman
11 жыл бұрын
So smart!!!!
@machiningmoments
12 жыл бұрын
Thanks
@abhaynandodkar8997
11 жыл бұрын
thanks a lot!
@FUNGAI407
10 жыл бұрын
yeah buddy thanx perfect vdo and explain brilliant
@machiningmoments
10 жыл бұрын
Fungai Chawasarira Glad it was helpful!
@VishwaProtimBanerjee
13 жыл бұрын
Thankx!
@machiningmoments
11 жыл бұрын
Thanks, I think...
@jansenjayjay4069
11 жыл бұрын
2 i think 19?
@umairraza6648
11 жыл бұрын
thank u very much
@thugbiz
10 жыл бұрын
Very helpful
@machiningmoments
10 жыл бұрын
Glad it helped!
@Anicool0123
11 жыл бұрын
yeah.. it will work.. thanks :D
@O-Ben
11 жыл бұрын
perfect!. and thanks.
@jhonvals6046
10 жыл бұрын
Thanks you God bless..
@machiningmoments
10 жыл бұрын
Glad it helped, thank you for your comment.
@thomashvnmusic
8 жыл бұрын
Thank you.
@machiningmoments
8 жыл бұрын
+Thomas Heaven Glad to help Thomas, thanks for saying so.
Пікірлер: 145