Junk yard may be cheaper but never know the problems you could run into with them too. Can't wait to see the progress of the rebuild
@BuildTuneRace
3 жыл бұрын
This is true!
@FreeRangeNomad
2 жыл бұрын
Great video. This is the info I was looking for. And idk how long the total process took. But was good to know that it's not quick results. Thank you.
@timsmallsreed1349
3 жыл бұрын
Another junkyard block is going to be cheaper than a re-sleeve and machining. But you never know what you are going to end up with. It might have issues too. Just make sure you hone and crosshatch the cylinders.
@BuildTuneRace
3 жыл бұрын
Yeah I definitely go back and forth on all this hard to start over and have another used block completely machine. Lots to thing about lol
@marteck319
2 жыл бұрын
Murat is acid! Safety glasses are a must.
@rustyass9736
3 жыл бұрын
I don’t know what you’re doing but I’ll hit the like 👍👍👍🇨🇦🇺🇸🇨🇦🇺🇸
@BuildTuneRace
3 жыл бұрын
Thanks for the support!
@CamaroRick
3 жыл бұрын
Decent 6.0's are getting harder to find
@BuildTuneRace
3 жыл бұрын
They are!
@raylund2036
3 жыл бұрын
Man that sucks I have been wondering what was going on with it and you havent seen you lately
@BuildTuneRace
3 жыл бұрын
Took a small break back at it now!
@ShutErDownBud
3 жыл бұрын
Would this work for a header bolt thats broken off in a head?
@BuildTuneRace
3 жыл бұрын
This only helps clean aluminum. Best way to remove a broke header bolt is to try and weld a nut onto the broken bolt.
@BeardedPharmacist
3 жыл бұрын
See if Texas Speed will help you out with a sleeved block.
@BuildTuneRace
3 жыл бұрын
Might not be a bad idea. Looking at all the options right now!
@NoMatureContent
3 жыл бұрын
Just grab another block. If you crack that under boost it's going to take a lot more with it than another block is going to cost.
@BuildTuneRace
3 жыл бұрын
Your not wrong looking at some options the last time we sleeved it and it’s been good but gets expensive
@NoMatureContent
3 жыл бұрын
@@BuildTuneRace is a short motor combo from texas speed or the likes out of the question?
@mikecrice3646
3 жыл бұрын
Where are your safety glasses? Your hands will heal up. Your eyes may not.
@BuildTuneRace
3 жыл бұрын
Should have put some on for sure! I made sure I wasn’t going to spray any in the direction of my face but still should have!
@Autofaze
3 жыл бұрын
Ah crap! That was cool to watch though
@BuildTuneRace
3 жыл бұрын
Thanks man! I definitely learned something new lol
@ronmonahan1696
3 жыл бұрын
tough break
@BuildTuneRace
3 жыл бұрын
Very!
@johnnelson4455
Жыл бұрын
One word when using acid and toothbrushes….EYEWEAR!
@edwinfeldman8231
3 жыл бұрын
Making my hands and face burn just watching the process. Sorry about the block...
@BuildTuneRace
3 жыл бұрын
😂 it was rough! Thanks for watching.
@StLMikie
3 жыл бұрын
Is it a GM block or aftermarket?
@BuildTuneRace
3 жыл бұрын
It’s a stock 6.0 block
@timweb1510
3 жыл бұрын
Where you been at man 😀
@BuildTuneRace
3 жыл бұрын
Life’s been crazy, just needed to take a small break but I’m back!
@timweb1510
3 жыл бұрын
@@BuildTuneRace hope you are doing well man 👍🏻
@BuildTuneRace
3 жыл бұрын
All is good thank you!
@BeardedPharmacist
3 жыл бұрын
Isn't muriatic acid what they use to the toilet bowl stains?
@BuildTuneRace
3 жыл бұрын
Idk maybe all it says in it is that it will etch concrete lol
@Dr.MikeTuneoligist
3 жыл бұрын
$100 junkyard block sounds cheaper......
@BuildTuneRace
3 жыл бұрын
Yeah if I have to have that one machined 30 over it might be close. That’s what I need to find out!
Пікірлер: 44