using a . 45 acp shell as a repair part is the most American thing I've seen
@poppeepete1471
8 жыл бұрын
This technique is AWESOME. Removed system from my 2002 Classic this morning. Take your time, have some patience, and overcome your reluctance to bang away on your bike with a hammer and file, and voila, it's all done in less than 1/2 hour. My AIS was cracked, so the weird sound is now gone. Much better than removing all the parts and pulling frozen pieces with pliers. If Byrds music is half as good as his ingenuity on bike modifications, I should be hearing him on the radio!
@Byrds1967
8 жыл бұрын
+Poppee Pete Hahaha....thank you kind sir! :-)
@davethemagnificent2576
4 жыл бұрын
I cut the 2 tabs on the bracket that hold the tubing, then put the bracket back on so it would continue to hold the cable.
@stephentetreault5398
8 жыл бұрын
thanks for the tips , sure makes it easier with help from guys like you !!
@usingtheirhypocracyagainst8636
5 жыл бұрын
working on mine right now and found these connectors also swivel out if you are patient enough. the system so called pump is not really even a pump just a vapor valve. just removed it all. I also re installed the clutch cable bracket but cut off any references to the pipes and applied silver paint to the edges. looks great when its all off.....
@waynevmax
8 жыл бұрын
Never pound on or pry with a file unless you don't like it! Nice video.
@jaykatcher1769
Жыл бұрын
By removing the system it resolved the backfire bug I had, my star has cobra pipes and a maximum k&n air kit so this was a must… you can also remove that pump if desired.. cool video, 👍
@Byrds1967
Жыл бұрын
Glad it worked out for you. Yeah, I didn't bother removing the pump.
@ahmodahmed1453
5 жыл бұрын
THANKS FOR THE TIPPED ON HOW TO REMOVE THE AIS PIPES , HOW ABOUT THE WIRES CONNECTING TO THE BIKE AND THE PUMP , SHOULD I REMOVE THE PUMP AND ITS ATTACHMENTS AS WELL?
@glennhuntiv2704
4 жыл бұрын
I just did it on my bike. I had no problems except for one of my tubes rusted out and was blowing exhaust at the lowest side of the tube. So i did it just to get rid of it. I did my a bit different but basically the same concept.
@Fatreddog
7 жыл бұрын
At 5:50 you can see how you are damaging the fin in the cylinder. I would be a little more cognizant of that if working on a customers bike, but nice job over all.
@D.Mulder
11 ай бұрын
Did this today on my BT1100 (same engine) Because we are not allowed to have guns, a bullet casing was a bit hard to find. So what i did was grind the plugs down, and welded them shut. Then i hammered them back in. 10 minute job max. Don't forget to plug of the airfilterbox.
@Byrds1967
11 ай бұрын
Did you notice any improvement?
@D.Mulder
11 ай бұрын
@@Byrds1967 It is still on the lift, Gonna rejet is also. Here in the netherlands they came with a little restrictor in the carbs, so im gonna get those out and rejet it. Also gonna get a k&n filter. It has some carbon exhausts and i think the previous owner did not do a rejet.
@Byrds1967
11 ай бұрын
@@D.Mulder Well have fun with it.
@usingtheirhypocracyagainst8636
5 жыл бұрын
also a fired 45 round is a perrrrfect fit.....awesome. amazon wants 20.00 for those machined tapered plugs on this application, I think I saved some money....
@CindyDC
Жыл бұрын
Could it be it’s the AIS that’s causing my exhaust to pop out the back when I let off the gas ?
@trey1sauce165
5 жыл бұрын
I have a 2007 which I pulled the stock baffles off, I am making the exhaust come out in a “true dual” way. So one pipe a side by just flipping the rear cylinder elbow! Anyways any word on reviews with my year ? I’m wanting to give this a shot because I have an issue with the popping myself which I’ve had 2 shops saying that the popping will happen no matter what I do?
@vadimfuks463
4 жыл бұрын
What about installing new filter on ais system?
@djjones8490
3 жыл бұрын
6:00 I think the dog was upset about being woke up from his nap with all the pounding (lol).
@10cents97
7 жыл бұрын
What I did on my 94 Virago 1100 was just remove the tubing and then hammer 9mm shells into the knuckle instead of hammering the knuckles out and hammering 45 shells into the head. Works just fine. If you ever want to remove them I think you could probably get them out with a drill. I used a 16 penny nail head to tap them in deep.
@Byrds1967
7 жыл бұрын
That sounds like a good option too.
@clivewinters7479
2 жыл бұрын
Brilliant Video made with good humour 🇬🇧
@Byrds1967
2 жыл бұрын
Thanks, glad to help.
@carlosgajardo3560
6 жыл бұрын
Hello my friend, I'm from Chile and I have the same motorbike for the elimination of the AIS
@arifsonfilm9662
3 жыл бұрын
After I disabled the system but left the pipes. In cold condition, the first kilometer, my bike isn't runing smoothly. What could be the reason?
@shitmonkey
Жыл бұрын
other than cosmetics why do you remove the fitting from the heads? you could JB weld the hole that the hose goes on and be done..
@ironhead320
4 жыл бұрын
What exhaust you Have on that
@jaybilawchuk2225
11 ай бұрын
Can anyone tell me if this richens or leans the plug burn once deleted?
@migflowers
7 жыл бұрын
Good video. Wouldn't feeding the tubes back into each other basically do the trick?
@Byrds1967
7 жыл бұрын
Yeah, but most want to remove the chrome tubing strapped all over their bike to give it a cleaner look.
@believerbyknowledge
6 жыл бұрын
It does, but some of us like the cleaner less cluttered view of a v twin
@Yzorixul
6 жыл бұрын
yeah but it looks cleaner this way. you should also be able to remove the ais pump itself too after this
@jg1912
7 жыл бұрын
major thnx man
@feasternate
5 жыл бұрын
My next project. Added some cobra pipes, and she's now too rich. The cackles are nice, but the backfires when decelerating can be fairly loud. Also I did not have to re-jet my 1100 for the cobra pipes. I should have, but they have an outer cover that would hide any blueing. But is that normal? To throw a aftermarket exhaust system on a completely stock bike, and burn rich?
@nathanmindermann7697
5 жыл бұрын
Backfiring on deceleration means it's actually lean. Rejetting the carbs is pretty much a must.
@Sotonsmr
6 жыл бұрын
@Byrds1967
6 жыл бұрын
No soldering necessary. Just tap the shells in as shown in the video.
@Sotonsmr
6 жыл бұрын
mine have holes in the bottom i meant the solder will cover them--- guess they've been fired?
@Byrds1967
6 жыл бұрын
I have fired shells but NO HOLE. Get some casings without a hole. Solder will probably melt under the intense heat and pressure of the cylinders.
@Sotonsmr
6 жыл бұрын
lmfao mate its not that easy- in UK to get fire arms or ammo...
@Sotonsmr
6 жыл бұрын
my bro in our club said solder would probably work... it is exhaust valve right? so not the same forces as say the piston
@ScalerWave
9 жыл бұрын
Whaaat? Only 1 beer? lol Nice job !
@denoc817
5 жыл бұрын
awww Come on! Sharing is Caring. Team work is Dream Work 🤣
@GaryFoltyn
4 жыл бұрын
What do you do with the line that runs down and into the pump? I’ve seen guys plug it with a golf tee but wouldn’t that fill up with gas? What’s the best to do here? Can it be removed? If so, do you need to pull the tank? TIA! 👍🏼
@YamMaxim700
2 жыл бұрын
Golf tee - since 2005
@gregoryblair9810
2 жыл бұрын
It is a vacumn line, so anything to plug. Usually a rubber fitting like on a car intake.
@steelhanded11
5 жыл бұрын
What's the reason for doing this???
@MG-ks1qg
4 жыл бұрын
Eliminate popping on deceleration
@shanewoolsey940
4 жыл бұрын
yeah, please tell me, I'm in Canada so getting a 45 casing is out of the question. HAHAHA, will my 762 sks work?
@scottjones5013
3 жыл бұрын
How does this stop backfiring what actually happens
@dantae666
3 жыл бұрын
@@scottjones5013 less air richer mixture
@vstar7196
3 жыл бұрын
@@MG-ks1qg Urban myth. The AIS doesn’t contribute to popping in the exhaust. Tune the air fuel mixture.
@robertsalyers1351
3 жыл бұрын
The Yamaha 1100 V -Star never was Fuel Injection 💉 always used a Carburetor I just purchased a gently used 2005 V-Star 1100 it was fitted with a custom seat , Cobra exhaust, cup holder, and an oils relocation kit She purrs like a Kitten 😸
@jigglepuff1218
10 ай бұрын
Yeah no shit
@ahmodahmed1453
5 жыл бұрын
THANKS FOR THE TIPPED,how the AIS pump and wires connecting to the bike?
@denoc817
5 жыл бұрын
Is it still back firing?
@Hasher411
8 жыл бұрын
Freeking awesome man, thanks for the video .... I will have to do that to my 2008 V-star 1100. I really love the sound of your bike. I just pulled out the baffles in my OEM pipes, but I like the sound of yours better. I will be jetting the carbs myself this winter and if I may ask, what are you using for pipes? How did you get that sound?
@electropentatonic
7 жыл бұрын
Should I hammer in an unfired 45 round?
@Byrds1967
7 жыл бұрын
That might be interesting....I wouldn't want to be around long to see the results.
@NormanGnome11
7 жыл бұрын
Go for it .... But please remember to video as we could all do with a laugh.
@seniorjuanvaldez
6 жыл бұрын
electropentatonic hammer both unspent. 45 shells in
@TheMarmaduke1975
6 жыл бұрын
I'll hold the beer!
@denoc817
5 жыл бұрын
You did Say 45 Round not 45 Shell. Yes Try it Please...I'll hold your beer and got your back. 🤣
@whsanford
6 жыл бұрын
Did this to my 2002 V-Star Classic and it backfires BADLY!!! But it is a used bike and someone knocked out the baffles from the exhaust pipes, do you think that is the reason for the backfiring?
@letmehearthatguitarsqueal
6 жыл бұрын
William Sanford it needs to be rejetted because the pipes opened up
@jottow680
6 жыл бұрын
it's running lean. mine did it too until I ritchened the idle air mixture and it helped. but it needs bigger jets.
@TheIrishAmish
2 жыл бұрын
.45 case, not “shell”. A “Shell” is a complete cartridge. GREAT VIDEO, THANK YOU!
@Byrds1967
2 жыл бұрын
Thanks.
@sPi711
9 ай бұрын
Put a whole shell in there if you want to hear some real popping noises.
@butterthebean
6 жыл бұрын
So what about the AIS pump? Do you just leave that on the bike permanently? I realize it's not doing anything now, but can you just remove it as well?
@Byrds1967
6 жыл бұрын
It looked a bit wedged to easily remove for me. Plus you'll probably have electrical and hoses to terminate. I just opted to keep the pump on there.
@vientulaisvilks4094
6 жыл бұрын
Hi mate. I been watching couple of similar videos but i did'n seen someone removing air pump??????? Why??? Do I need it for something else????
@Byrds1967
6 жыл бұрын
You can remove the air pump if you want. You then might have to terminate some electrical lines to it. It's just more easy to do it the way shown for most riders who want to simply bypass it.
@sPi711
9 ай бұрын
I don't see why one just wouldn't take the AIS hoses from the cylinder heads and just use a rubber cap with a hose clamp similar to what you have on the right side of the carburetor where you connect your manometer. If you hammer on that rear (or front) cylinder AIS connector the way it's shown here, you risk binding it on the way out and possibly deform the hole. I always like to be able to reverse anything I do, and that might make it impossible.
@ahmodahmed1453
5 жыл бұрын
should you also dismount the pump and terminate wires to it, the system does not needed anymore.
@glennhuntiv2704
5 жыл бұрын
ahmod ahmed good question I’d like to know the same thing
@nathanriggins230
4 жыл бұрын
Yes you can, the pump is only powered by vacuum. There are no wires to worry about. Just remember to reinstall the bolts after removing the pump.
@turbopower1098
2 жыл бұрын
Hello, do you know if the 02 Eu version has the AIS system ? I can't find it on mine. thanks
@Byrds1967
2 жыл бұрын
I'm not sure. It might just be a U.S. California requirement.
@carlosgajardo3560
6 жыл бұрын
hola amigo soy de chile y tengo la misma moto para que sirve la eliminacion del AIS
@believerbyknowledge
6 жыл бұрын
Si has cambiado el mofle por tubos directos (cobras o vance hines) te ayuda a eliminar las explosiones esto por supuesto si tambien has cambiado el sistema de filtro de aire , el motor de las vstar puede entregar como 20 HP adicionales con cambiar el mofle el sistema de filtro de aire a uno mas directo y con esto evitas las explosiones
@johncarder5472
6 жыл бұрын
My hoses crinkle like shut do they have to be open oh great video
@Byrds1967
6 жыл бұрын
My hose has a sharp bend in it too. It doesn't make a difference. The pump is basically just feeding itself now, and has no effect on the engine.
@alanremple4621
Жыл бұрын
Hi made the mod and couldn’t have been easier. No more backfire or pops from the removal of stock baffles. Could you do an update with suggestions for the actual pump decommission or removal? I see you left all 3 hoses (two large and one vacuum style) disconnected.
@Byrds1967
Жыл бұрын
The pump isn't running anything anymore. In my case I'm just leaving it in there. It looks like a person would have to remove a lot of parts to get to it.
@davidparker8662
8 ай бұрын
@@Byrds1967 So when you left the air pump did you leave hoses in the by-pass mode like in your video or hook them like they are susposed to be . just a question i havnt completed the removal of the hoses yet but damn sure will
@Byrds1967
8 ай бұрын
@@davidparker8662 Honestly I probably left the air pump looped into itself. I left the air pump on the bike too. Those things are tucked away and hidden as it is. The main mission was to seal the cylinders (with 45 shells) and remove the extra tubing.
@blazintrails3023
3 жыл бұрын
What does this do for the bike? Someone bypassed mine previously and the hose blew out
@Byrds1967
3 жыл бұрын
It recycles unburnt fuel back into the cylinder to reburn it. It's more for EPA concerns. Folks get rid of the system to: 1) Give their bike a cleaner look. and 2) Get rid of the vacuum draw on the cylinders.
@justanotheropossumchannel5304
3 жыл бұрын
Im new to the V star club and im curious.... why would you want to remove the AIS?
@andrewkaiser6230
3 жыл бұрын
It’s supposed to help with the loud backfiring if you have aftermarket pipes.
@brentinchley4798
8 жыл бұрын
Nice I am gonna do that to my 2009 custom get rid of those damn tubes, but the guy who said that you can't get hand guns in canada is wrong you can get them no problem with the right paper work.
@XV250
8 жыл бұрын
Yeah, but it is a fair bit of paperwork...
@brentinchley4798
8 жыл бұрын
+LS650 yup you are correct on that one
@xvs4162
6 жыл бұрын
2 day course little test and good to go. I own several here. and then of course the waiting time when you purchase a restricted firearm lol
@halmorse5879
4 жыл бұрын
Thats what Sucky Gun Control does to you.....Permits for this Permits for that...more restrictions on you and more money for the Politicians.
@jeffstevenson3044
4 жыл бұрын
Do not do this unless you have replaced the stock exhaust and had the bike tuned, also if you go this far you might as well remove the pump too.
@BendeRosa12
2 жыл бұрын
Why do you have to replace the stock exhaust. Can you modify the stock exhaust? What is the issue with replacing the stock exhaust before doing this?
@jaykatcher1769
Жыл бұрын
With cobra pipes and maximum air kit this was a must do.. my bike backfired in the lower gears and this stopped it…
@donbraham411
5 жыл бұрын
Why do this will bike run better and richer what’s the reason for doing this ? Thanks Don
@justanotheropossumchannel5304
3 жыл бұрын
You have probably figured it out by now, but essentially it was a requirement for the stock exhaust. If you do any kind of aftermarket exhaust or drill out your baffles you will "probably" needed to disable the AIS because you will more then likely be running too rich and your exhaust will be back firing or popping.
@donbraham411
3 жыл бұрын
Wow my 1100 is long gone
@CindyDC
Жыл бұрын
I have a question, can this be done but somehow leave the Chrome tubing,. ? I like the looks of the chrome tubing,..
@Byrds1967
Жыл бұрын
Yeah, you can leave the chrome tubing if you want. Once you bend the AIS system tube into itself, the system no longer works. And my V-Star started popping after I put straight pipes on it. I don't think that has anything to do with the AIS system.
@CindyDC
Жыл бұрын
@@Byrds1967 I just bought the bike, it has Vance & Hines and was put on professionally,. I’m wondering if the redone the jets ?
@Byrds1967
Жыл бұрын
@@CindyDC So if your Vance & Hines installer put on straight pipes and a bigger air intake system then they should have redone the jets as well. My bike pops all the time on deceleration. The increased power is worth the pops.
@CindyDC
Жыл бұрын
@@Byrds1967 the person I bought it from said he had them done by a professional ,.. thank you for replying 😊
@austinweiers1461
4 жыл бұрын
will thisnwork for a 2001 classic?
@Byrds1967
4 жыл бұрын
Yeah, it should be exactly the same.
@Flizzor
Жыл бұрын
Does it make your bike sound different? And what’s the benefit of this ?
@Byrds1967
Жыл бұрын
It's supposed to get rid of that vacuum leak that would go through the pump and recycle unused gas. I just like how it cleans up the look of the bike.
@jnanney95
7 жыл бұрын
what do you mean by permanent damage
@Byrds1967
7 жыл бұрын
Just saying feed the hoses back into the system to see how the bike runs before you remove (tear out) all of your tubing.
@brianvandergriff4440
8 жыл бұрын
I just got my Yamaha V Star and I'm wondering what is the purpose for removing the AIS system
@justanotheropossumchannel5304
3 жыл бұрын
@PauseDenied Oh damn so thats where the small back fires are coming from? I have 4.5 inch cobra exhausts and the the popping has been really bugging me. I even did a valve adjustment and was all "I guess its just how the bike is".
@sabwoodturning3254
2 жыл бұрын
@@justanotheropossumchannel5304 hey man - just wondering if you did this and whether it helped? Just bought a 2004 with aftermarket pipes and have some loud decel pop. Also getting high vibration at 70mph for some reason (engine related as it goes when I pull in the clutch). Gonna try this and also sync the carbs 👍🏼
@davidbolduc-henri7790
2 жыл бұрын
Can you just take de rubber hose off and plug the metal hose
@Byrds1967
2 жыл бұрын
I suppose you could. The bike looks better without it.
@davidbolduc-henri7790
2 жыл бұрын
@@Byrds1967 ok thks and it seem to be working fine 👌
@403patriot3
9 жыл бұрын
.45 colt ACP i wish i could have got these instead of the black plugs i have. damn...if only we could have handguns in canada it would be perfect here nice bike...
@xvs4162
6 жыл бұрын
not sure where you got that info from. i live in canada and own several handguns and chambered in .45ACP .. simple course for an RPAL and you are good to go.
@86bigred
5 жыл бұрын
Go to a range and pick up some spent 45 shells. Dont need no pal for that. I use empty shells for making gasket bolt holes to cheap to buy punches.
@SammyEddie
4 жыл бұрын
If it’s not illegal to send an empty 45 casing in the mail I’ll send you one. Or go to a shooting range and grab one.
@ulysessandiego6655
6 жыл бұрын
im new on having my v star 1100.. what would be the good outcome of removing AIS?..
@Byrds1967
6 жыл бұрын
Well a stock bike has average power and good gas mileage. Most folks get: 1) Straight pipes, 2) Max Air Filter Relocation Kit, and 3) Remove AIS System. Doing those 3 things will increase your power 20%......but you will lose gas mileage.
@ulysessandiego6655
6 жыл бұрын
thank you very much for the info sir.. i really appreciate it. Godspeed!
@Byrds1967
6 жыл бұрын
No problem....enjoy, it's a great bike.
@jonathanvillalba3214
3 жыл бұрын
So you go from 40Hp to almost 50Hp or do you just accelerste faster due to unrestricted combustion?
@danjohnson7306
3 жыл бұрын
@@Byrds1967 hi, what does the system actually do ?? Cheers Dan
@johncarder5472
6 жыл бұрын
Ok
@devio1990
9 жыл бұрын
Is the system any different on a classic?
@Byrds1967
9 жыл бұрын
Devin Canard I think the only difference on the classic is some exterior hardware like bigger head light, and longer fenders. The engine and AIS system should be exactly the same.
@stephentetreault5398
8 жыл бұрын
+Devin Canard same motor in either classic or custom 1100 from 1998 -2011
@Byrds1967
8 жыл бұрын
+Devin Canard No, it shouldn't be any different.
@efrencillo00
6 жыл бұрын
Could this be done on the 99 model?
@Byrds1967
6 жыл бұрын
I looked at some pics of the 99 model, it seems to be laid out the same.
@efrencillo00
6 жыл бұрын
Thanks a lot
@TonyStewartKY
7 жыл бұрын
Please forgive my ignorance, I just bought a 2000 xvs1100. After searching google I found your video. Maybe unrelated, but I am having an issue with the oil light staying on and the oil level is just fine! It came on yesterday after hitting a pot-hole, and although there is no visible damage and the bike and runs fine, the freaking light comes on after a couple of minutes and stays on. Anyone experienced this issue? Also, Why remove the AIS?
@Byrds1967
7 жыл бұрын
The only time my oil light ever came on was when I had really old oil in it and had exceeded 4500 miles before a change, otherwise mine has never come on. As for the AIS....if you plan on putting on straight pipes and a better air filter system then disabling the AIS is the icing on the cake. You'll squeeze every ounce of power that bike has to offer.
@cyrusstothard
6 жыл бұрын
The possible reason for your oil light staying on is likely your oil pressure sensor being gummed up
@trreb1
6 жыл бұрын
If the oil pressure sensor is not gummed up like Cyrus said then it may be going out OR you can check the connection of the wire at the sensor. I've had an issue like this with my neutral safety switch and it was a loose connection.
@terrancehumphries2369
11 ай бұрын
you dont have to do that just block the tubes of but leve the pump to do its thing thats ok
@jeffyoung478
3 жыл бұрын
The real fix for popping or backfiring on deceleration is to have your carbs cleaned and tuned properly. It will also prevent you from beating the hell out of your ride.
@arifsonfilm9662
3 жыл бұрын
That is just not True, I cleaned up, tunad, everything and it back fired again. As soon as I took off the AIS, it never happened again
@sugamai
3 жыл бұрын
@@arifsonfilm9662 agree
@carlosgajardo3560
6 жыл бұрын
Gracias amigo y por ultimo el sonido en cada cambio es normal
@Byrds1967
6 жыл бұрын
Thanks.
@chaser631
7 жыл бұрын
Interesting, but... i have v-star 1100 2005 (from Mount Rainer national park) imported to Russia. Installed V&H pipes (in USA), no more modifications.... and - no "shots" in exhaust! AIS is still on the bike. Some more of chome pipes on bike :P
@believerbyknowledge
6 жыл бұрын
rejet your carbs if they havent and remove the AIS and you will gain about 20 HP it means no more looking for 6th gear
@user-xz8st8cy3i
5 жыл бұрын
А у меня есть выстрелы с аналогичной системой
@davidpayson9360
3 жыл бұрын
What dose it do
@Byrds1967
3 жыл бұрын
The AIS system recycles unspent fuel back into the cylinders to be burnt. It's all part of EPA stuff.
@isitreal1521
3 жыл бұрын
Used solid aluminium plugs now my bike makes a chirp noise
@randallhuston1466
7 жыл бұрын
Thanks much for this video. I have a 1986 Virago XV700 and thought this system was some sort of PCV system. So you can just plug them eh?
@Byrds1967
7 жыл бұрын
I had a 1983 Virago 750 at one time but didn't mess with the AIS system on that particular bike, it had enough power . If it's put together like the Vstar then the directions should work. Just make sure you "run the pump into itself and the cylinders into themselves" with the rubber hoses for a test ride first. If you like the change then plug them.
@jottow680
6 жыл бұрын
all it does is add extra air to the exhaust after the valve to pass emisions. it really has no effect on power.
@carandme1
Жыл бұрын
Why did you remove this system?
@Byrds1967
Жыл бұрын
I was seeking more power at the time, and to get rid of any vacuum leaks that might exist. I also wanted a cleaner look for the bike.
@carandme1
Жыл бұрын
@@Byrds1967 I have a backfiring problem in the top pipe. Could this AIS system be the problem?
@Byrds1967
Жыл бұрын
@@carandme1 Mine still backfires a lot on deceleration. Based on that, I doubt the AIS system would improve it much.
@bobbysweeney5377
6 жыл бұрын
I did the hose swap as a test run and it did absolutely nothing positive for my 05 v star 1100. Ran like it wasn't too happy to the point of me thinking this was a prank video
@Byrds1967
6 жыл бұрын
Is your bike stock or have you put on straight pipes and modified the air intake?
@bobbysweeney5377
6 жыл бұрын
Byrds1967 I just purchased it recently but it appears that the previous owner has chopped and gutted the stock pipes. I'm assuming he jetted it as well because it's not running poorly.
@Byrds1967
6 жыл бұрын
Generally these bikes are made to 'reburn" unused gas through the AIS system as not to allow harmful emissions into the atmosphere. When you put on straight pipes or mess with air intake then the AIS system will backfire a lot as the unused gas explodes in the pipes. Just poking holes in the muffler may not change much (if that's what he did). You can increase horsepower at least 15% if you do stuff correctly. Disabling he AIS system is just the icing on the cake....after all that. And yes, jetting the carbs (both of them) is the key after all mods are made.
@bobbysweeney5377
6 жыл бұрын
Byrds1967 Thank you for the tips. It still seemed to backfire a fair amount and after a little while, it seemed to start falling on it's face a bit. I'm thinking I might need to adjust these carbs a bit.
@lilianacabreriza6823
6 жыл бұрын
Bobby Sweeney LM2250E-XX-B 2" Grease Pumps and Packages
@cedler426
5 жыл бұрын
Will this work with 2 into 1 exhaust?
@Byrds1967
5 жыл бұрын
If you're running straight pipes into 1 I don't think it will matter. To get the best performance you don't want a baffle in the pipe(s).
@mario930131
4 жыл бұрын
45 shell!!!!!!!!! What the !!!!!!🤔
@cedler426
5 жыл бұрын
I did mine and now it makes a chirping sound on deceleration
@Byrds1967
5 жыл бұрын
Are you running straight pipes and modified air filter? The AIS was the last thing I did to pull the last bit of power from the bike. Mine backfires on deceleration, but it's worth the trade off.
@cedler426
5 жыл бұрын
@@Byrds1967 They are cobra straight pipes carbs been rejetted stock air intake. runs great but hate the chirping through exhaust. I think they gave me the wrong size plugs from pacific coast. I think they are supposed to fill the whole hole. seems like plugs are too short.
@cedler426
5 жыл бұрын
Now I got to think of a way to get the plug kit out and put in the new ones I bought from baron customs. They look like they are longer to fill the whole tube insert. That way there is no open space inside the cylinder to make the chirping sound go away.
@denoc817
5 жыл бұрын
sounds like a air leak.
@cedler426
5 жыл бұрын
@@denoc817 I went ahead and put the 45shells in the holes made chirping sounds still but are starting to fade the more I ride. There is no air leak anywhere I made sure
@bryanmiller5074
2 жыл бұрын
The pms screw will also solve this issue... 🤫🤫🤫
@tat2dpom
7 ай бұрын
Why do ya remove it whats the benefit 😉
@Byrds1967
7 ай бұрын
I removed it mainly to clean up the look of the bike. The AIS system recycles unspent fumes back into the cylinders for EPA reasons. It really has no bearing on how the bike runs.
@benefieldharcourt9931
7 жыл бұрын
so exactly why are you doing this
@Byrds1967
7 жыл бұрын
The bike runs better without it. The AIS recycles unburnt gas back into the system which use to make it backfire a lot.
@jimjacobsen9963
5 жыл бұрын
Byrds1967 what pipes are you running?
@bufordtannen7004
7 жыл бұрын
la mejor herramienta??... el martillo XDD
@MikeKitterman
4 жыл бұрын
Please know that I have never used foul language in a KZitem.com comment. To do so is entirely out of character for me, but.... 1.) What the fuck is an AIS system? 2.) Why the fuck would I want to beat on my bike and take the damned thing out?
@danmeredith6354
8 жыл бұрын
Tell me, whats the advantage of doing all this????? Does the bike run better? I don't get it!
@Byrds1967
8 жыл бұрын
For mine it stopped back firing. With the AIS system it would cycle through un-burnt fuel back into the cylinders and would backfire a lot on deceleration.
@danmeredith6354
8 жыл бұрын
Byrds 1967>>>I get it, I have a 2006 1700 Roadstar probably with the AIS, it backfires a lot.....Wondering if that system can be removed also!
@Byrds1967
8 жыл бұрын
As long as it's carbureted it probably has one that can be removed. Fuel injected you can't. Just follow the silver tubes to the cylinders and see where it all goes.
@danmeredith6354
8 жыл бұрын
Thanks!
@michaelulrichsr1536
7 жыл бұрын
Hay Bro. I have a 03 1100. I closed all the tubes off awhile back. cause it was the (reed valve) that went out. All this bad crap was running out. I toke it off. So now what do you do with the vacuum line. The guy at the shop plugged it. I did have it in my tool box with a fuel filter on it to keep dirt out. but sense he plugged it now I get oil coming out the carb. what's your option.
@earlgallup5223
6 ай бұрын
Goofy goofball 😂😂😂
@vstar7196
4 жыл бұрын
The AIS as designed serves a useful. It allows these bikes to operate in states that have stricter emission standards. But it also helps to reduce carbon pollution. Removing/altering the AIS is selfishly irresponsible.
@easyrider920
4 жыл бұрын
You sound like the typical LibTard! Trump 2020!!!!!
@curtisssmith5204
3 жыл бұрын
GE Clay It’s muppets like you that are the reason we have emission laws. The clean air and water act was passed by republicans under the Nixon administration. So much for your libtard comment. Modern cars and motorcycles have pretty good power as well as being fuel efficient and cleaner. My hat’s off to the engineers that make it work.
Пікірлер: 216