Love your video, thanks to your tutorial i was able to do it by myself and saved a lot of money
@asiba2
6 жыл бұрын
very good time consuming and informative
@BlackTalon53
4 жыл бұрын
It took me FOREVER to get the safety clip at 6:32 out. It wasnt a clip but some twisted bit of stainless steel wire. I had to get to get my Dremel with the miniature cutting wheel insert out into my driveway and cut it off, and then cut a slit into the end of the safety bolt so I could twist it in its hole with a screwdriver and pull out the remaining bit of the stainless steel wire from the backside of the bolt. It was a gigantic pain in the behind.
@LOREGUINNESS
3 жыл бұрын
Thanks for sharing. What did you use After ?
@BlackTalon53
3 жыл бұрын
@@LOREGUINNESS I used one of the clips that hold the body shells of my RC cars on their chassis. They have to be slightly shortened first so you can push them in as far as ncessary, and they rust fast in the hole too though. I may try a couple of twisted together strands from a stainless Bowden cable next.
@BlackTalon53
3 жыл бұрын
@@LOREGUINNESS I used one of the clips that hold the body shells of my RC cars in place on their chassis. That works really well. They have to be shortened with a Dremel first too so they can be pushed sufficiently far in though, and they rust fast in the hole too. I may try some twisted together strands from a stainless steel Bowden cable next.
@LOREGUINNESS
3 жыл бұрын
@@BlackTalon53 thanks. What do you think using a simple iron wire from the bobbin? A well knotted One.
@BlackTalon53
3 жыл бұрын
@@LOREGUINNESS I think it would rust in the hole too, and it might be too brittle and break. I have been thinking about cutting a groove in the extreme end of the pin and securing it with an E-clip. That way I wouldnt have to put anything in the hole at all.
@arnoteerink
6 жыл бұрын
Why remove the caliper ??? To change the brake disk...you only have to remove the 12 size bolts at the back (sadel). If you change only the brake pads...remove pin at the underside...than you flip the calliper up...and change pads... Pushing back pignon first...also verry easy this way... Easy as hell.
@pauljones1350
2 жыл бұрын
Spasibo za remoht
@pauljones1350
2 жыл бұрын
This is great thankyou dosvedania,jacking point is further down ledge little arrow points to it,are there any brake retaining spring clips holding pads on 2013 panda pop 1.2 do you know anyone or just retaining pin like this
@blitziderdonnergott
5 жыл бұрын
Danke hat super geklappt.👌👍
@anselmfritsch5728
5 жыл бұрын
Constantin, did you forget to push the brake hose back into the holder? If yes, please do this, otherwise the hose will tear. Constantin, hast Du vergessen, den Bremsschlauch wieder einzuhängen? Falls ja, mache das doch noch, sonst besteht die Gefahr dass der Bremsschlauch kaputt geht.
@hamishanderson8619
7 жыл бұрын
Great video Bud!! What did you do about the fault code though, or did it not come up?
@ConstantinLehadus
7 жыл бұрын
I do not have error code
@MotoRoUsa
7 жыл бұрын
Cam mult a durat domnul Cristian haha
@Fd20y
Жыл бұрын
No jack stands? Ridiculous to do this held on a standard jack
@petruttiberiu6981
7 жыл бұрын
Trebuia sa le strângi mult mai bine.. si în loc sa dai cu acea vaselină mai bine dădeai cu o pasta autoblocanta ... -cu direcția si cu frânele nu te joci!-
@petruttiberiu6981
7 жыл бұрын
Si trebuia sa schimbi si garniturile la pistonas
@jonj4222
5 жыл бұрын
Salut am si eu o Panda 1.1 2004,am schimbat si eu discurile si dupa o luna s-au ovalizat.Discurile au fost TRW placutele la fel.Ale tale au mers bine?Cu rugina ai probleme?
@ConstantinLehadus
5 жыл бұрын
Salut referitor la discuri si placute nu am avut probleme cu ele, masina am vanduto la niste rude si sunt foarte multumiti
@tygerbright117
3 жыл бұрын
I don't think that is the jacking point!
@remusrms7252
3 жыл бұрын
Salut..ce dimensiune au discurile tale ?
@ConstantinLehadus
3 жыл бұрын
Nu mai stiu am vandut masina dar era super tare fiatul
@anselmfritsch5728
5 жыл бұрын
By the way: It is not the only error you make, but the worst one. Nebenbei: Das ist nicht der einzige Fehler den Du machst, aber der schlimmste.
@SoloTravel.D
7 жыл бұрын
Salut Ai idee cum pot face sa aprind faza scurta si proiectoarele cand inchid masina din cheie ?! Am o panda exact ca a ta :) Ms !!
@ConstantinLehadus
7 жыл бұрын
Salut. nu ma pricep la partea electrica.
@SoloTravel.D
7 жыл бұрын
Ahhh :(( Ms oricum de reply :) Ma batea gandul sa schimb si eu placutele dar mi.e frica de pistonul ala ca n.am cum sa.l fortez inapoi Oricum f okay tutorialul :)
@ConstantinLehadus
7 жыл бұрын
eu am avut probleme pe spate cu cilindru frana cand l-am inlocuit sa rupt conducta pentru ca era corodata rau si nu sa mai desfacut
Пікірлер: 34