I really appreciate you showing us even the little things. Some of us - like me - know squat about this stuff...and I want to learn as much as I realistically can. And you are helping me with that. Peace.
@kman-mi7su
3 жыл бұрын
You just reminded me of something on my "to do" list I have to change out the gear oil in my 88 Ford F250 and both axles on my 04 Toyota RAV4. I guess I know what I'll be doing on Friday morning. Nice day to do it today where I'm at, but I'm on a ladder today painting my house. Took a break from it and your notification popped up so I immediately had to see it. Thanks for the great video. 👍
@WatchWesWork
3 жыл бұрын
The torque spec you found is just the start of the preload adjustment procedure. You start at 89 ft-lbs and then adjust in 10 ft-lb increments until the rolling drag is in spec. I looked and Toyota doesn't give a procedure for reusing the crush sleeve. But, on every other manufacturer I've seen you are supposed to measure the rolling drag of the whole differential before you take it apart, then when you reassemble it you adjust until it's about 5 in-lbs greater. It's really tricky to do. I always take the wheels off and back off the calipers if it has disk brakes. Even then it's a PITA to get a consistent measurement of the rolling drag. But, I doubt it makes any difference!
@nickbro9040
3 жыл бұрын
Glad to see more videos. I always learn something from you.Thanks!
@Ezrider359
3 жыл бұрын
Glad to hear it!
@RileyNA
3 жыл бұрын
I love my 09 Tacoma. Its just a little 4 cyl 2.7, nothing too fun, but shes got 200,000 miles and purrs like a kitten. Love the videos, especially the big diesel repairs
@lonelyplanet1080
3 жыл бұрын
What up EZ, good to see your finding time to get work done on the 'Yota... that's a nice little truck
@ericcorse
3 жыл бұрын
Ezra when you grabbed a finger of that gear oil I thought you were going to taste it. It looks real clean under there.
@my1969mgb
3 жыл бұрын
Enjoyable to watch you do something on here. Why ?? Because you finish what you start. I have a bit of a problem with stopping and walking away before something is done. Keep it up. We enjoy your efforts immensely.
@behroozkhaleghirad
3 жыл бұрын
The fact that you balanced that drive shaft so damn well amazes me. Because it's a specific job which requires it's own shop and specialist to do it. Very good 👍👍👍
@Ezrider359
3 жыл бұрын
Yeah it wasn't weight balanced made sure the phasing was dead on and the run-out was acceptable. But it turns smooth as can be with no vibration. The front driveshaft that is factory however the phasing is out a couple degrees and has a vibration over about 45-50 if you have the hubs locked in...lol that might be a video for another day
@user-dx3fx7hd4i
3 жыл бұрын
I follow you from Iraq .. Your posts are great, you are very good
@j.c.smithprojects
3 жыл бұрын
sockets make some of the best seal drivers! smooth as glass! the toyota is ready for another 100k miles.
@Ezrider359
3 жыл бұрын
i probably use sockets more often than the seal driver kit i have.
@TheDmcintosh18
3 жыл бұрын
I really enjoy the content of all of your videos. Must admit I'm like most I expect as I prefer old red. But you're good at what you do so keep it going. All the best from the U K.
@dearanel936
3 жыл бұрын
I sure love that pretty new tailgate
@lewiemcneely9143
3 жыл бұрын
My S-10 is an 89 so I guess we're 89-in laws! Good job, Ezra! GBWYall!
@peterdingley5321
3 жыл бұрын
Just found your threads online. Found your youtube. Inspirational!! Exactly what I want to do with my 90 2wd 22r! And my rear pinion seal is leaking LOL. Looks awesome. Can't wait to lift mine a bit.
@Anthony_T.
3 жыл бұрын
Always good to see content from you. Im always learning something new each time
@doughboy1966
3 жыл бұрын
I like the steel wheels on that truck. Nothing wrong with saving a truck by combining two together.
@Ezrider359
3 жыл бұрын
i don't mind the white wagon wheels i wouldn't mind getting a set of the chrome steel rims with the round holes for it (my mind is blank what most people call them for some reason)
@alexsmelly2263
3 жыл бұрын
Yo that truck looks mean like that though with the white steelies and matte grey. Glad to see you posting again
@sudd2685
3 жыл бұрын
Pretty work young man thank you for your videos
@stuartpardner7668
3 жыл бұрын
Brilliant work great videos 👍👍👍👍
@rmbuser
3 жыл бұрын
Awesome Video and thank you for sharing!!! Great Detail!!!
@MCMLXXXIV1984
3 жыл бұрын
Here he goes! Another great video
@kilroyb1128
3 жыл бұрын
EZ u make everything look Eazzy. Thankyou great vid
@davidsnowball2981
3 жыл бұрын
Great work as usual. Regards from Australia
@skinny-peters-JR.
3 жыл бұрын
I had a 1988 Toyota 2wheel. Drive truck...replace pinion seal on it back in.2005 .or 2006....truck had...180k. On it... And replace brake light switch trigger. Right above break pedal....
@Asdasd-kb9ib
3 жыл бұрын
Good luck 👍
@Ezrider359
3 жыл бұрын
Thanks! You too!
@travisbosco8469
3 жыл бұрын
Great video.
@davidanddiana7173
3 жыл бұрын
Cool stuff man 👍
@johnbrady6756
3 жыл бұрын
another great video love the fact you got drain bucket after the spill on floor ha ha.Proves you'r human like lots of us we all forget 🤢👍Homer moment Doooh !!!!!!
@Ezrider359
3 жыл бұрын
Glad you enjoyed it
@masterofdisaster7427
3 жыл бұрын
I own a Landrover and just gave up on the pinion leak. Changed the seal a few times but after a while it starts to leak again. Just fill it up every now and then, and let it mark its spot. sometimes you win sometimes you lose.😢
@tmack2090
3 жыл бұрын
thanks for the video ez !! very helpful as always !!! be safe !!!
@Ezrider359
3 жыл бұрын
Thank you t Mack
@johnzwicker204
3 жыл бұрын
Well done
@goodselections
2 жыл бұрын
Thank you. I need to do something like that soon on toyota '88. close to 400K. don't spill oil on your cool shop.
@akrocco
8 ай бұрын
Thank you, helpfull!!
@speedandmarine9066
3 жыл бұрын
Front pinion seal was leaking on my parts chasing/work pickup which uses a crush sleeve. I figured after 300k on that diff the bearings have a little wear and rattling it on with the impact just reset it to factory! Sounds good, and it was cold and late so.....all good! That is a cool old Toyota and now leak free(less?).
@Daves_adventures4315
3 жыл бұрын
Wahoo! Nother Ezra video!
@erichouser6337
3 жыл бұрын
How did u shorten drive? I would love to see video if u ever do again. I love ur videos so easy to follow. Especially for us shade tree mechanics, thanks brother your friend from Larned kansas Eric Houser.
@Ezrider359
3 жыл бұрын
its in the video where i put this truck together out of two trucks, i think it was called 89 toyota pickup revival or something close to that.
@erichouser6337
3 жыл бұрын
Hey brother good to see you bro. Love the content.
@Ezrider359
3 жыл бұрын
Thanks for the visit
@erichouser6337
3 жыл бұрын
@@Ezrider359 Hey are selling in merch so I can help support your channel more? I would live to have a tshirt of old red or even that sweet looking jaguar! Anything to help you brother.
@Ezrider359
3 жыл бұрын
not currently I probably will in the future though.
@tarzan1392
3 жыл бұрын
HEY EASY YOU REMIND ME OF ME.....I HAD THE SAME CAREER.....GOOD MEMORIES...THANKS FOR ALL YOU DO !!!
@chuckychuck
3 жыл бұрын
👍👍
@adamchilton
3 жыл бұрын
Any idea on the size of the nut that holds the yoke on? And a ball park of the socket you used to press the seal in?
@Daves_adventures4315
3 жыл бұрын
If it makes you feel better I gagged when you pulled the seal out. I cannot stand the smell of 80/90.
@Ezrider359
3 жыл бұрын
esp when its old, new gear oil isn't too bad old gear oil is pretty gross.
@Dave-1277
3 жыл бұрын
On the tailgate vid, you left with one garbage bag in the truck, this time you pull in with three! lmao sorry just found it funny. Keep the good videos coming Ezra!
@Ezrider359
3 жыл бұрын
Lol. Don't have trash pickup at the shop both videos were recorded just before I left for the day on different days. This one was recorded same day as the old red update video
@Dave-1277
3 жыл бұрын
@@Ezrider359 It just struck me funny lol
@iandermott6558
3 жыл бұрын
Turtle here great work i don't have your nice pump and that gear oil stinky stuff
@bruceleonard81
3 жыл бұрын
Always thinking my list just got longer lol diffs and transfer case
@roadtrain5910
3 жыл бұрын
what's the cable hanging down on the drivers side with crimped loop? an old stabilizer???
@Ezrider359
3 жыл бұрын
the exhaust was hanging off that at one time, it does nothing now needs to be removed.
@roadtrain5910
3 жыл бұрын
@@Ezrider359 all good there cheers Ezra
@james37603
3 жыл бұрын
Maybe in future do a video of replacing the seal if it has a crush sleeve? Thank you
@Ezrider359
3 жыл бұрын
it did have a crush sleeve, the crush sleeve is further in the diff its used to set pinion depth by tightening the pinion nut witch is why i said it was important not to over torque it.
@james37603
3 жыл бұрын
I am sorry my mistake Thank you.
@mauriciocruz5531
3 жыл бұрын
Good job can i get the part number.
@edgar76222
3 жыл бұрын
Wasup man
@bryanschmidt9539
3 жыл бұрын
Where u live at in South Dakota
@robertmurillo9662
3 жыл бұрын
Is the front bumper original?
@Ezrider359
3 жыл бұрын
Not factory but a very popular aftermarket bumper from the 80's
@robertmurillo9662
3 жыл бұрын
@@Ezrider359 is it a SB bumper I always wondered if the SM bumpers work fine. For my fathers 86 Toyota.
@Ezrider359
3 жыл бұрын
Yeah it's a Smitty built. I bought it second hand probably sometime in the late 90's it wasn't originally for that truck as I had to cut the mounts off and make different mounts but they are good bumpers. That one is probably older than the truck 😂
@kilroyb1128
3 жыл бұрын
U have a 100 mile commute. Wow.Wat the hoosie is up with tha??
@Ezrider359
3 жыл бұрын
No I don't have a 100 mile commute just needed to go somewhere that was 100 miles away and used that truck
@kilroyb1128
3 жыл бұрын
@@Ezrider359 oh ok u are still the man Thankyou
@MCMLXXXIV1984
3 жыл бұрын
I bet those bolts feel strangely fragile compared to the heavy duty 18 wheeler ones
@Ezrider359
3 жыл бұрын
Lol yeah every time I work on automotive stuff everything seems so tiny
@MCMLXXXIV1984
3 жыл бұрын
I can imagine 😄
@dearanel936
3 жыл бұрын
Bad news Anytime a private company gets every bit as big as the United States government
@dearanel936
3 жыл бұрын
Before Google is gone please keep googling I do it too
@Ezrider359
3 жыл бұрын
Now days there is so much information available at your fingertips
@vernonslone8627
3 жыл бұрын
Didn't think you could reuse a crush sleeve...
@Ezrider359
3 жыл бұрын
If the crush sleeve is crushed beyond proper pinion depth it has to be replaced. Initial setup would involve tighten the nut until proper pinion depth is set. For what I'm doing here what you are doing is torquing it to a amount that is tight enough but not so tight that your going to further crush the sleeve.
@dougsweldingfabrication953
3 жыл бұрын
4:08 is she fresh as a daisy?
@terryp920
3 жыл бұрын
A piece of baling wire!
@Ezrider359
3 жыл бұрын
Potato patata
@MadMax-yq9ix
3 жыл бұрын
I'm early!
@Ezrider359
3 жыл бұрын
Better early than late is what she said 😜
@MadMax-yq9ix
3 жыл бұрын
@@Ezrider359 haha xD
@user-ix6tt9sd4j
3 жыл бұрын
Привет, как погода в Америке?
@Ezrider359
3 жыл бұрын
сегодня идет снег здесь, в северной дакоте
@user-ix6tt9sd4j
3 жыл бұрын
@@Ezrider359 у нас тоже сегодня выпал на Урале, вовремя переобулся.
Пікірлер: 104