Can't get any easier than that, simple and direct without a word said . nice job thank you
@jerryturensky
3 жыл бұрын
You're welcome!
@joepawlu9523
2 жыл бұрын
@@jerryturensky what is the part number for the bearing and seals. Thx I can't find em anywhere I got a gm 10 bolt 3.23 gears and a 26 spline thx
@jerryturensky
2 жыл бұрын
@@joepawlu9523 I found the part numbers in Rock Auto, sorry I don't have the part numbers, it was a long time ago.
@AeroSS87
Жыл бұрын
@@joepawlu9523 I'm a bit late here, but I ordered FAG FC67147. German company. Really good quality. Unlike the Chinese BCA stuff these days.
@nonyadamnbusiness9887
7 жыл бұрын
You left out the part where you have to buy a kit to extract the broken retaining screw in the differential cross shaft before you can pull the C-clip and pull the axle. Nice video of the last steps. Doing it right with proper driving tools.
@willmills1370
4 жыл бұрын
Yup, mine broke too. Got the extractor kit from Summit Racing. Yukon Gear and Axle makes it but doesn't sell it to the public. I watched CVSahara his video on KZitem on replacing that dam Pinion Retaining bolt, I bought two more from Autoplicity for my '79 Trans Am, it came in yesterday. Ain't got nothing else to do with this COVID 19 lock down.
@fultonguyy
Жыл бұрын
Like your quick to the point video, having to do the same on 2000 blazer, glad to see you put wheel bearing grease to lube the bearing another video use lucas, but wheel bearing grease is the way.
@dang_industries
2 жыл бұрын
Great video! Easy job but I came here to confirm how deep the seal should end up (looks about 1/8” past flush)
@jerryturensky
2 жыл бұрын
I pressed it in til it stopped
@MrDeepwatermarine
4 ай бұрын
I came here to find the attachment for my slide hammer you’re using
@dtuck0509
4 жыл бұрын
Straight to the point, great video.
@jerryturensky
3 жыл бұрын
Thanks
@dustyhinton7639
4 жыл бұрын
Do not do that with your axle shaft the bearing puller will slide through the seal if you can pop them both out at once
@Boz_-st4jt
Жыл бұрын
Not sure I'd let this guy touch my 01 2500 HD? Much less change the oil! Was astonished he would use the axle splines to remove the seal!
@jerryturensky
10 ай бұрын
Cause racecar
@jasonlewallen7146
5 ай бұрын
@@jerryturenskyfreaking out about popping a “seal” as you did. They’d stroke if shown the other things folks do on race cars. 😂
@oldbiker9739
Ай бұрын
@@Boz_-st4jt its just a seal they been doing that since they started with rawhide seals
@Bacon676
6 жыл бұрын
Fantastic fucking video. Short, simple, right to it. Just what I was looking for.
@mikeb6902
24 күн бұрын
would I be correct in assuming when you are driving the bearings in, when you hear a change in sound, that means the bearing is fully seated? Thank you.
@bellingsen
2 жыл бұрын
How can I tell it`s a 7.5" or 7.625 inch? I have this 1999 pontiac firebird trans am v8 convertible. I had some differential issues and ordered bearings for 7.6". Problems! I think it`s 7.5" . What is the difference and where can I find the right number 7.5" or 7.6"...?
@oldbiker9739
Ай бұрын
the 7.5.or 7.6 10 bolt has sharp horns on the bottom rear diff casting . the 8,5 has a square casting at rear housing .
@oldbiker9739
Ай бұрын
hers how you tell , kzitem.info/news/bejne/25mP26GKqGuTlKw
@gza06955
7 жыл бұрын
Thank you Jerry
@sugargoldy
5 жыл бұрын
Good video thank you I needed my memory refreshed
@FromThe3PointLine
7 жыл бұрын
thanks man this was helpful to me in houston tx
@FromThe3PointLine
3 жыл бұрын
@Marc Owens OK kid
@ralfhinojosa
4 жыл бұрын
Thank you for the video
@wilsonwichman4847
Ай бұрын
Does the axle just pop out ir do i need tk remove anything
@IsleOfFeldspar
Жыл бұрын
Does the gear oil lubricate that bearing too? I’m not a mechanic.
@jerryturensky
Жыл бұрын
yes it does, that's why its important to have the right amount of gear oil in the differential.
@jays4forces
7 жыл бұрын
what bearings did you use BC for whatever reason...I can't seem to find any for my 87 cutlass..7.5
@cheflewisanthony4685
4 жыл бұрын
If that's bad will it make a loud thump noise
@HectorMartinez-fq6cy
7 жыл бұрын
Real helpful, much appreciated.
@WilliamYaughn
4 ай бұрын
Who ,akes that tool that he is using to drive the bearing in?
@jerryturensky
4 ай бұрын
Harbor Freight
@isaacwashington9925
8 жыл бұрын
great video. thanks!!!!
@dakotawelsh5709
2 жыл бұрын
Does anyone know where you can get that tool to put the new bearing in?
@mr.nobody68
2 жыл бұрын
Use a large socket
@jerryturensky
2 жыл бұрын
Harbor Freight
@daviddejesus7037
10 ай бұрын
Where did u get the puller bud ?
@jerryturensky
10 ай бұрын
Fee tool rental O'reilly auto parts, Phoenix AZ
@but199018
8 жыл бұрын
What's the exact name of the tools you were using? (Drive tool and puller)
@jerryturensky
5 жыл бұрын
Harbor Frieght tools
@nobullshit9721
4 жыл бұрын
jerryturensky lol 😂 seemed to work pretty well overall tho
@efarley164
8 жыл бұрын
What tool are you using to pull the bearing...it was so quick. We've tried several brands of bearing pullers for our 1970 Chevelle and none work.
@wll1500
5 жыл бұрын
He literally just used the axle lol
@austinmouw3383
4 жыл бұрын
@@wll1500 He asked about the bearing, not the seal.
@wll1500
4 жыл бұрын
@@austinmouw3383 erm.... The bearing just comes right out with the seal.
@austinmouw3383
4 жыл бұрын
wll1500 I think you need to watch the video again. He uses a slide hammer to pop the bearing out
@wll1500
4 жыл бұрын
@@austinmouw3383 welp fuck, I just made myself look like an idiot. I thought this thread was from another video about a trailer hub...
@veggiepowered
4 жыл бұрын
Is That A G20 Van ?
@jerryturensky
3 жыл бұрын
1986 Monte Carlo
@jayme8614
6 жыл бұрын
I'm wrong it's not spring should be twards the oil my car was installed wrong from the factory
@79monte
2 жыл бұрын
Dude say something tell me which way the bearing supposed to go in that's what I'm looking for because it does matter and you're just sitting here quiet as mouse
@jerryturensky
2 жыл бұрын
I made this video to show friends I work on my own race car, hope this video helps, cause I did not show removing the axles.
Пікірлер: 61