Push the axles in from both sides and the C clips will fall inside the housing. The axles will easily pull out after that. Replace the c clips upon reinstall
@stewoe7157
10 ай бұрын
This is either a B or O type axle. Retained by the flange with four bolts, not with c-clips.
@lucyh9559
6 ай бұрын
Nice and simple. I wonder if a big ass prybar will do the same on a stuck axle
@whoiswaynereynolds5457
3 жыл бұрын
What's that puller called again? The big Joey? 😂
@budsodalsky
Жыл бұрын
No C clips? I thought the trademark of GM was those C clips!
@jajonjohnson3865
11 ай бұрын
I'm wondering how he got them off without removing the clips myself 🤔
@stewoe7157
4 ай бұрын
Olds and Buick rear ends didn't have those.
@KensStuff
3 жыл бұрын
I"m not trying to be a know it all. but that diff didn't have C clips inside holding the axles like a 12 does. you didn't need to pull the cover or the cross pin to get the axles out. still a good video. l like that slid hammer it's a beast.
@OutlawEdge
3 жыл бұрын
Yeah the backing plate holds in the axle so i pulled out the bolts holding on the backing plate to remove the axles. I pulled everything apart to inspect and sandblast the housing 👍
@KensStuff
3 жыл бұрын
@@OutlawEdge I totally understand now. i didn't know you was cleaning and sand blasting it.
@ranbymonkeys2384
Жыл бұрын
@@OutlawEdge No he's saying the "c" clips on the other end of the axels where the gears are there should be c clips that need removed before you use the puller.
@rickhammar1636
3 жыл бұрын
I just changed the rear end in my truck because that 5/16 bolt that holds that pin that holds spider gears in broke off. Boy did that suck.
@markt9438
4 ай бұрын
I made something way easy large bolt approximately 1 1/2 inches long , try to make this as long as you can. with three nuts on it two that are locked in place and one with washers in front of it big enough to go against the spider gears then holding the lock nuts in rotating the night against the washers in between the center of the two axles and by pushing up against the spider gear it will push out one of the axles then just reverse it and do the other one against the opposite spider gear this is the easiest and safest way I know!
@moniquesanchez9576
2 ай бұрын
Hi I have a 70 Monte Carlo. I am looking for new axels and I want to confirm they aren’t c clip type?
@OutlawEdge
2 ай бұрын
@@moniquesanchez9576 is that a 10 bolt or 12 bolt rearend?
@whoiswaynereynolds5457
3 жыл бұрын
Good job brother! Not you Joe Schmoe!
@stewoe7157
10 ай бұрын
You left out an important detail. This rear end, as you said, is from an Oldsmobile chassis. Buick and Olds 8.5's are different from Chevy's, as they aren't retained with C-clips. Therefore the removal procedure will be very different on a Chevy.
@markt9438
4 ай бұрын
Not on 10 bolts 8.5 Olds Cutlass they do not have c clips he nailed it
@stewoe7157
4 ай бұрын
@@markt9438 There are different versions of 10 bolt axles. Some have c-clips, some don't. The versions used in Oldsmobile don't have c-clips, the ones in Chevrolet do.
@henrye718
3 жыл бұрын
How does this man not have more subscribers. So versatile and so much knowledge and he's sharing it for free.
@EdgeofEternityBillCameron
Жыл бұрын
I looked for the best 10 bolt rear end video and this one popped up!!! Awesome Arco!!!
@brianferris1233
3 жыл бұрын
🌲🦅🌲 Thank you for posting your video have a safe healthy day 🌲
@johnnylom9915
3 жыл бұрын
I use a magnet to pull the pin out Works everytime
@mikegorieu6997
4 ай бұрын
Limited slip differential G80
@miguelreyes6144
Ай бұрын
What if the pin is stuck and doesn’t want to slide out after taking the 5/16 bolt off ? 1:55
@OutlawEdge
Ай бұрын
@@miguelreyes6144 you can use a brass punch to knock it out 👍
@miguelreyes6144
Ай бұрын
@@OutlawEdge thank you boss
@benjamintaylor6791
Жыл бұрын
Would you have the info on where I can find those longer wheel studs?
@OutlawEdge
Жыл бұрын
Yeah they are race car wheel studs from speedway 👍😁 ARCO
@IronHorseGarage
3 жыл бұрын
Just like that!!!
@davidm2778
3 ай бұрын
Awesome video.....
@mitchaellll
Жыл бұрын
Painful Push axle in, spin, & pull it out don't have to pull 4 backing plate bolts to do an axle....smh
@whoiswaynereynolds5457
3 жыл бұрын
It's a cross shaft 🤪
@ronaldriggins5096
Жыл бұрын
Thankyou.very clear and to the point
@moparnut6286
3 жыл бұрын
How is axle bearing end play adjusted on this rear or is it non adjustable?
@OutlawEdge
3 жыл бұрын
As far as i know its not adjustable bro 👍
@moparnut6286
3 жыл бұрын
@@OutlawEdge Cool thanks ARCO it's a Buick old Pontiac deal bolt in 10 bolt axle rear no adjustments I never had one in hand.... went and read up on it on the H.A.M.B. board learn something new every day! Later Chevy 10 bolts are c clip type axles that I have dealt with before.
@TrendsbySterling
3 жыл бұрын
Awesome puller Arco!
@ajbanz2737
2 ай бұрын
Nasty ass tool box 😂😂
@ajbanz2737
2 ай бұрын
Thanks for the help tho
@petesmodelcarcustoms584
3 жыл бұрын
5 a. m. My time. When this went out. So I must be about 100th again😩. Was there any obvious damage to the spline lands or excessive wear anywhere? 🤔Arco.
@OutlawEdge
3 жыл бұрын
No brother it looked like new inside there 👍👍👍
@myconight
3 жыл бұрын
5 am, and I am still late...😅🤘🏻
@KUGW
3 жыл бұрын
22nd floor please lol
@THROTTLEPOWER
3 жыл бұрын
Great vid!!!!!
@mattthescrapwhisperer
3 жыл бұрын
Big Jerk LOL!
@richardaragon1391
2 жыл бұрын
Great narration also
@whoiswaynereynolds5457
3 жыл бұрын
First
@eliaslourenzo8312
3 жыл бұрын
Exellent idea, very good extractor.
@frekkledipped
2 жыл бұрын
so you only have 1 axle? Not posi? I have posi and looking to how remove both
@OutlawEdge
2 жыл бұрын
Its pretty much the same way. Its kinda simple bro. Just dive in and do it. Don’t let it intimidate you. 👍thanks for watching
Пікірлер: 53