Loved the video. Will refer back to it often. Thanks again.
@robinreed8057
5 жыл бұрын
Just picked up a new string from ya. Great string. Great video
@Putuj_Igumane
2 жыл бұрын
Monster Wake - yes sir indeed! I did struggle to tune that one! Had to buy me a set of top hats. But once tuned, it shoots like a dream :-) difficult to shoot though, due to low brace hight, unforgivable bow
@acewelding
5 ай бұрын
Sweeeet!
@bowhunter0762
5 жыл бұрын
Awesome!!
@richardganz9318
4 жыл бұрын
Great video , I just replaced my strings on my Triax and Mathews Yokes are a little bit of a pain. The yokes are so close to the cams . I going to reinstall my string again following your steps an see if I get a little bit more space between yokes and cams my mathews Triax
@bltefft
4 жыл бұрын
Thanks for the nice video. I looked at it because I have to change out just my bottom cam.
@Jari_Kuusisto
4 жыл бұрын
Do you use cam hats to correct paper tears, or do you adjust rest also? Thanks for the very helpfull video!
@mrradiation1354
5 жыл бұрын
Good video, thanks for all the tips. One thing though, that high pitched sound that kept going on during the video, man thats hard on the ears, and makes the video difficult to listen too.
@richardganz9318
4 жыл бұрын
Great video, I changed my triax strings and the yolks are very difficult to get perfect they come so close to the cam anybody have any secret tips
@philiparmstrong3247
3 жыл бұрын
I have a PSE supra and would love to know how to make a bowstring with how to take measurements etc. considering me a beginner
@luissandoval4093
3 жыл бұрын
good stuff Jer, thanks So for timing purposes, you add a twist to the string(?) at the end that hits first right? I read a comment below where you said that you add a twist but to the cable of that same cam. At this point I am confused. Is it to the string or to the cable? thanks
@h0tkoko
3 жыл бұрын
Hey Jeremy, how do I know where to put my peep on the string? Is there some sort of rule or guide to where the peep should be on the string so that it would not be too low or too high?
@anthonystancliff2826
5 жыл бұрын
When you say add a twist to the top cam you meen take the cable off the bottom and give it a twist or twist the cable that connects to top cam ?
@tripleb2128
4 жыл бұрын
Which ever stop touches first you add a twist to the cable on that cam. So his top cam stop hit first, so he took control cable off top cam and added a twist.
@TheIceman101
4 жыл бұрын
Good stuff man. Thanks
@marksmith2864
Жыл бұрын
Just had cables and string put on my Halon. Timing marks are good but ATA is 1/4 long and I have cables in my sight picture. What can be done too resolve this issue?
@motiv870
Жыл бұрын
I just had my local archery shop put custom strings on my Mathews Halon 6 and the cables are about 1/4" or basically no where near running through the timing holes on the cams.. and the bows axle to axle is sitting at a little less than 29 ³/⁴" which factory spec is 30".. is this acceptable? Or did this archery shop mess up?
@wcwcgarner2717
Жыл бұрын
Your timing should be correct. After a new set of strings are put on. And your axle to axle should be 30inches. You need to twist the control cable.
@mattdemarce8753
4 жыл бұрын
Is there a reason you're not taking an axle to axle measurement?
@jimmywallhanger8402
3 жыл бұрын
He can't find his measuring tape in that mess of a shop.
@jimmywallhanger8402
3 жыл бұрын
There a new technology out.... it's called a broom.
@wayneo1082
2 жыл бұрын
You did everything so fast without taking your time and showing everyone exactly what you did. Wish you would of been slower. Most people don't know how to do the stuff and with your video I still don't. Next!
Пікірлер: 23