Thank you thank you thank you sir. I have one of these things that I inherited from my father who passed away in 2017. I needed to thread the broken end of my 1 1/4 galvanized intake water line but I had no idea how to use it. I watched your video a couple of times and my pipe is now nicely threaded. Many thanks.
@jakemilkovich1722
8 ай бұрын
Makes me glad I own a Ridgid 300.
@sergeantsewer856
2 ай бұрын
These are great, I love manual dies sure its more muscle but you don't have to mess with adjustable dies trying to get 1 or 2 threads dialed in
@peterfarmer9058
3 ай бұрын
Very good information! I did not know how to expand to the 2 inch setting
@heavyfeather6682
5 жыл бұрын
Thank you for posting this got one of these from my grandpa but had no idea how to set it
@user-zf4qs2jy3n
3 жыл бұрын
I've never seen one of these. Sure makes me love the 12r set.
@shannonelliott6116
Жыл бұрын
If the teeth are worn, and that is likely, start with the ring set above the STD mark, makes deeper threads. If your threads need to be more shallow, start with the ring set below the STD mark. After doing 15 threads on 2" pipe, I found out the hard way when I had to re-thread those earlier pipes.
@rctoliveira6595
6 жыл бұрын
Exelénte, es todo lo que queria ver, me venden una igual de segunda mano a muy buen precio y solo queria ver aqui como es que funciona. [Thank You My Frend]
@mrfarmall-vk4gw
2 жыл бұрын
I just picked up one of these at a flea market thanks for the tutorial!👍
@georei
7 ай бұрын
I use this hand threader from time to time. 1" and 1.25" its not too bad, but to do 2", Ill just set up my ridgid 300.
@stevemarkovic9326
Жыл бұрын
Fantastic! Thank you for making this video!!!
@youtubier2839
6 жыл бұрын
great video!!. i was wondering how they worked!!
@minouchat
Жыл бұрын
Same thing for me as morelleca1 explains. thank you very much sir for this very good video
@lujitsu1251
2 жыл бұрын
Excellent
@Bleriotman
Жыл бұрын
Can this be set to cut threads on a 1.1875" diameter pipe? In other words, are the diameters pre-set, or can you do odd sizes as well? Thanks!
@shieldcracker
Жыл бұрын
They are preset to 1, 1.25, 1.5 and 2 in.
@winterkoi1366
6 жыл бұрын
Nice video! I have the same one
@richardgranville8820
3 жыл бұрын
Have you ever changed the dies. Picked one up cheap rusted pretty bad . Can't get the dies to loosen, any ideas?
@aleksandarslozenjicin2511
Жыл бұрын
Hi, Looking to buy a manual Ridgid Pipe Threader. As I understand it, both the 65R-C or 65R-TC have interchangeable parts. But I cannot find specific differences between the two. Any experiences/advice would be greatly appreciated.
@craigtate5930
Жыл бұрын
Sorry I can't help with that
@foxstan
Жыл бұрын
65R-C uses a clamp screw to engage the work jaw to hold it onto the pipe while the 65R-TC uses a locking cam instead. Cam makes it faster to install and remove on the pipe.
@albertventura4736
3 жыл бұрын
Good
@toddmcneil5653
Жыл бұрын
Can't figure out how to loosen and turn out the 3 jaw part to make travel room to thread .
@craigtate5930
Жыл бұрын
Unfortunately it's been so long ago I don't recall much about it
Пікірлер: 25