Paul, thanks from 🇨🇱 Chile. I starting with the restoration of my chevy C10, 1981. Your videos are the best for start to working....👏
@marvinalancornell8275
4 жыл бұрын
Paul, I've done this soooo many times it's not funny at least 5or6 times. I've had from 1964c10 thru 1972c10's. Your doing a great job keep-um coming.
@tcollier4017
4 жыл бұрын
Progress! Looking good.
@punkinsgarageandpaint8299
4 жыл бұрын
I use to have a 72 step side. I miss that truck!
@lyleveach2936
3 жыл бұрын
Love your videos. Just started a 68 c10 from ground up.
@erikrapoport7318
4 жыл бұрын
Keep em coming!
@duncanduzit6201
3 жыл бұрын
You are doing a great job boss. Especially like the 4k. I'm inspired to make a change in resolution for my vids.
@janicespickelmire9355
3 жыл бұрын
Great videos! What are you setting your Hobart welder at for the butt welds?
@JustWatchingJoshua
4 жыл бұрын
Just a quick question. Are you putting the cab mount floor braces back in it? I saw the front one rusted off but didn’t see it go in before the front floor patch panel.
@paulkc10
4 жыл бұрын
Yep. Gonna flip the cab on its back and do them all at once.
@CarlosCarlos-2018
4 жыл бұрын
Love the contents brother,good work and stay safe,Paul i have the same welder, hobart 190,what set up do you use for 16g sheet metal and specially the gas set up ? Thank you again and please keep those videos coming 🙏🏽
@paulkc10
4 жыл бұрын
I use what it recommends on the chart inside it. All of these patch panels are 18-20ga
@CarlosCarlos-2018
4 жыл бұрын
paulk_c10 thank you again
@mechanicmike1236
4 жыл бұрын
Cab is progressing very well, are you smoothing the firewall also? Take care and stay healthy!
@paulkc10
4 жыл бұрын
Just the heater core delete. Otherwise leaving it alone.
@donaldbaker6961
3 жыл бұрын
Who do you get your parts from LMC ? Or brothers?
@jayinmi3706
4 жыл бұрын
I saw the door locating tip in a thread on Pro-Touring.com, it was keepat's Charger. Maybe there?
@paulkc10
4 жыл бұрын
Nah that’s not it. Been racking my brain. Idk, at least I remembered it haha
@andyschoo4177
3 жыл бұрын
@@paulkc10 Stout Custom's channel? I've seen him do that.
@briantorrez7927
4 жыл бұрын
Where did you get your stand idea? Also do you have the dimensions for your stand?
@paulkc10
4 жыл бұрын
kzitem.info/news/bejne/wGNq13qdgGt-qGU
@bobcat138
4 жыл бұрын
can you give the info on that pinch weld repair panel please?
@paulkc10
4 жыл бұрын
Kaminskichassisfab.com
@bobcat138
4 жыл бұрын
@@paulkc10 thank you paul. I was hoping the repair panel would be taller but it will help my project 1969 k20
@paulkc10
4 жыл бұрын
To go into the rolled portion? How high up does it need to go? The cab corner patch panels have a portion of that you could maybe use?
@bobcat138
4 жыл бұрын
@@paulkc10 about 6 inches up about where the cab floor level is inside the cab. I cut the back off another cab but it also has some damage where the indents are.
@paulkc10
4 жыл бұрын
Message the guys I sent you. They can make what you need.
Пікірлер: 28